/** @file
  Debug Port Library implementation based on usb3 debug port.

  Copyright (c) 2014 - 2015, Intel Corporation. All rights reserved.<BR>
  This program and the accompanying materials
  are licensed and made available under the terms and conditions of the BSD License
  which accompanies this distribution.  The full text of the license may be found at
  http://opensource.org/licenses/bsd-license.php.

  THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
  WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.

**/

#ifndef __USB3_DEBUG_PORT_LIB_INTERNAL__
#define __USB3_DEBUG_PORT_LIB_INTERNAL__

#include <Uefi.h>
#include <Base.h>
#include <IndustryStandard/Usb.h>
#include <Library/IoLib.h>
#include <IndustryStandard/Pci.h>
#include <Library/PcdLib.h>
#include <Library/UefiLib.h>
#include <Library/UefiBootServicesTableLib.h>
#include <Library/MemoryAllocationLib.h>
#include <Library/DebugLib.h>
#include <Library/BaseMemoryLib.h>
#include <Library/BaseLib.h>
#include <Library/TimerLib.h>
#include <Library/DebugCommunicationLib.h>
#include <Library/PciLib.h>

//
// USB Debug GUID value
//
#define USB3_DBG_GUID \
    { \
      0xb2a56f4d, 0x9177, 0x4fc8, { 0xa6, 0x77, 0xdd, 0x96, 0x3e, 0xb4, 0xcb, 0x1b } \
    }

//
// The state machine of usb debug port
//
#define USB3DBG_NO_DBG_CAB    0   // The XHCI host controller does not support debug capability
#define USB3DBG_DBG_CAB       1   // The XHCI host controller supports debug capability
#define USB3DBG_ENABLED       2   // The XHCI debug device is enabled
#define USB3DBG_NOT_ENABLED   4   // The XHCI debug device is not enabled

#define USB3_DEBUG_PORT_WRITE_MAX_PACKET_SIZE 0x08

//
// MaxPacketSize for DbC Endpoint Descriptor IN and OUT
//
#define XHCI_DEBUG_DEVICE_MAX_PACKET_SIZE    0x400

#define XHCI_DEBUG_DEVICE_VENDOR_ID   0x0525
#define XHCI_DEBUG_DEVICE_PRODUCT_ID  0x127A
#define XHCI_DEBUG_DEVICE_PROTOCOL    0xFF
#define XHCI_DEBUG_DEVICE_REVISION    0x00

#define XHCI_BASE_ADDRESS_64_BIT_MASK 0xFFFFFFFFFFFF0000ULL
#define XHCI_BASE_ADDRESS_32_BIT_MASK 0xFFFF0000

#define PCI_CAPABILITY_ID_DEBUG_PORT  0x0A
#define XHC_HCCPARAMS_OFFSET          0x10
#define XHC_CAPABILITY_ID_MASK        0xFF
#define XHC_NEXT_CAPABILITY_MASK      0xFF00

#define XHC_HCSPARAMS1_OFFSET         0x4    // Structural Parameters 1
#define XHC_USBCMD_OFFSET             0x0    // USB Command Register Offset
#define XHC_USBSTS_OFFSET             0x4    // USB Status Register Offset
#define XHC_PORTSC_OFFSET             0x400  // Port Status and Control Register Offset

#define XHC_USBCMD_RUN                BIT0  // Run/Stop
#define XHC_USBCMD_RESET              BIT1  // Host Controller Reset

#define XHC_USBSTS_HALT               BIT0

//
// Indicate the timeout when data is transferred in microsecond. 0 means infinite timeout.
//
#define DATA_TRANSFER_WRITE_TIMEOUT      0
#define DATA_TRANSFER_READ_TIMEOUT       50000
#define DATA_TRANSFER_POLL_TIMEOUT       1000

//
// XHCI port power off/on delay
//
#define XHC_DEBUG_PORT_ON_OFF_DELAY    100000

//
// USB debug device string descritpor (header size + unicode string length)
//
#define STRING0_DESC_LEN      4
#define MANU_DESC_LEN         12
#define PRODUCT_DESC_LEN      40
#define SERIAL_DESC_LEN       4

//
// Debug Capability Register Offset
//
#define XHC_DC_DCID                  0x0
#define XHC_DC_DCDB                  0x4
#define XHC_DC_DCERSTSZ              0x8
#define XHC_DC_DCERSTBA              0x10
#define XHC_DC_DCERDP                0x18
#define XHC_DC_DCCTRL                0x20
#define XHC_DC_DCST                  0x24
#define XHC_DC_DCPORTSC              0x28
#define XHC_DC_DCCP                  0x30
#define XHC_DC_DCDDI1                0x38
#define XHC_DC_DCDDI2                0x3C

#define TRB_TYPE_LINK                6

#define ERST_NUMBER                  0x01
#define TR_RING_TRB_NUMBER           0x100
#define EVENT_RING_TRB_NUMBER        0x200

#define ED_BULK_OUT                  2
#define ED_BULK_IN                   6

#define XHC_LOW_32BIT(Addr64)          ((UINT32)(((UINTN)(Addr64)) & 0xFFFFFFFF))
#define XHC_HIGH_32BIT(Addr64)         ((UINT32)(RShiftU64((UINT64)(UINTN)(Addr64), 32) & 0xFFFFFFFF))
#define XHC_BIT_IS_SET(Data, Bit)      ((BOOLEAN)(((Data) & (Bit)) == (Bit)))

//
// Endpoint Type (EP Type).
//
#define ED_NOT_VALID                          0
#define ED_ISOCH_OUT                          1
#define ED_BULK_OUT                           2
#define ED_INTERRUPT_OUT                      3
#define ED_CONTROL_BIDIR                      4
#define ED_ISOCH_IN                           5
#define ED_BULK_IN                            6
#define ED_INTERRUPT_IN                       7

//
// 6.4.5 TRB Completion Codes
//
#define TRB_COMPLETION_INVALID                0
#define TRB_COMPLETION_SUCCESS                1
#define TRB_COMPLETION_DATA_BUFFER_ERROR      2
#define TRB_COMPLETION_BABBLE_ERROR           3
#define TRB_COMPLETION_USB_TRANSACTION_ERROR  4
#define TRB_COMPLETION_TRB_ERROR              5
#define TRB_COMPLETION_STALL_ERROR            6
#define TRB_COMPLETION_SHORT_PACKET           13

//
// 6.4.6 TRB Types
//
#define TRB_TYPE_NORMAL                       1
#define TRB_TYPE_SETUP_STAGE                  2
#define TRB_TYPE_DATA_STAGE                   3
#define TRB_TYPE_STATUS_STAGE                 4
#define TRB_TYPE_ISOCH                        5
#define TRB_TYPE_LINK                         6
#define TRB_TYPE_EVENT_DATA                   7
#define TRB_TYPE_NO_OP                        8
#define TRB_TYPE_EN_SLOT                      9
#define TRB_TYPE_DIS_SLOT                     10
#define TRB_TYPE_ADDRESS_DEV                  11
#define TRB_TYPE_CON_ENDPOINT                 12
#define TRB_TYPE_EVALU_CONTXT                 13
#define TRB_TYPE_RESET_ENDPOINT               14
#define TRB_TYPE_STOP_ENDPOINT                15
#define TRB_TYPE_SET_TR_DEQUE                 16
#define TRB_TYPE_RESET_DEV                    17
#define TRB_TYPE_GET_PORT_BANW                21
#define TRB_TYPE_FORCE_HEADER                 22
#define TRB_TYPE_NO_OP_COMMAND                23
#define TRB_TYPE_TRANS_EVENT                  32
#define TRB_TYPE_COMMAND_COMPLT_EVENT         33
#define TRB_TYPE_PORT_STATUS_CHANGE_EVENT     34
#define TRB_TYPE_HOST_CONTROLLER_EVENT        37
#define TRB_TYPE_DEVICE_NOTIFI_EVENT          38
#define TRB_TYPE_MFINDEX_WRAP_EVENT           39

//
// Convert millisecond to microsecond.
//
#define XHC_1_MILLISECOND                     (1000)
#define XHC_POLL_DELAY                        (1000)
#define XHC_GENERIC_TIMEOUT                   (10 * 1000)

#define EFI_USB_SPEED_FULL                    0x0000  ///< 12 Mb/s, USB 1.1 OHCI and UHCI HC.
#define EFI_USB_SPEED_LOW                     0x0001  ///< 1 Mb/s, USB 1.1 OHCI and UHCI HC.
#define EFI_USB_SPEED_HIGH                    0x0002  ///< 480 Mb/s, USB 2.0 EHCI HC.
#define EFI_USB_SPEED_SUPER                   0x0003  ///< 4.8 Gb/s, USB 3.0 XHCI HC.

//
// Transfer types, used in URB to identify the transfer type
//
#define XHC_CTRL_TRANSFER                     0x01
#define XHC_BULK_TRANSFER                     0x02
#define XHC_INT_TRANSFER_SYNC                 0x04
#define XHC_INT_TRANSFER_ASYNC                0x08
#define XHC_INT_ONLY_TRANSFER_ASYNC           0x10

//
// USB Transfer Results
//
#define EFI_USB_NOERROR             0x00
#define EFI_USB_ERR_NOTEXECUTE      0x01
#define EFI_USB_ERR_STALL           0x02
#define EFI_USB_ERR_BUFFER          0x04
#define EFI_USB_ERR_BABBLE          0x08
#define EFI_USB_ERR_NAK             0x10
#define EFI_USB_ERR_CRC             0x20
#define EFI_USB_ERR_TIMEOUT         0x40
#define EFI_USB_ERR_BITSTUFF        0x80
#define EFI_USB_ERR_SYSTEM          0x100

#pragma pack(1)

//
// 7.6.9 OUT/IN EP Context: 64 bytes
// 7.6.9.2 When used by the DbC it is always a 64 byte data structure
//
typedef struct _ENDPOINT_CONTEXT_64 {
  UINT32                  EPState:3;
  UINT32                  RsvdZ1:5;
  UINT32                  Mult:2;         // set to 0
  UINT32                  MaxPStreams:5;  // set to 0
  UINT32                  LSA:1;          // set to 0
  UINT32                  Interval:8;     // set to 0
  UINT32                  RsvdZ2:8;

  UINT32                  RsvdZ3:1;
  UINT32                  CErr:2;
  UINT32                  EPType:3;
  UINT32                  RsvdZ4:1;
  UINT32                  HID:1;          // set to 0
  UINT32                  MaxBurstSize:8;
  UINT32                  MaxPacketSize:16;

  UINT32                  PtrLo;

  UINT32                  PtrHi;

  UINT32                  AverageTRBLength:16;
  UINT32                  MaxESITPayload:16;  // set to 0

  UINT32                  RsvdZ5;             // Reserved
  UINT32                  RsvdZ6;
  UINT32                  RsvdZ7;
  
  UINT32                  RsvdZ8;
  UINT32                  RsvdZ9;
  UINT32                  RsvdZ10;
  UINT32                  RsvdZ11;
  
  UINT32                  RsvdZ12;
  UINT32                  RsvdZ13;
  UINT32                  RsvdZ14;
  UINT32                  RsvdZ15;
} ENDPOINT_CONTEXT_64;

//
// 6.4.1.1 Normal TRB: 16 bytes
// A Normal TRB is used in several ways; exclusively on Bulk and Interrupt Transfer Rings for normal and
// Scatter/Gather operations, to define additional data buffers for Scatter/Gather operations on Isoch Transfer
// Rings, and to define the Data stage information for Control Transfer Rings.
//
typedef struct _TRANSFER_TRB_NORMAL {
  UINT32                  TRBPtrLo;

  UINT32                  TRBPtrHi;

  UINT32                  Length:17;
  UINT32                  TDSize:5;
  UINT32                  IntTarget:10;

  UINT32                  CycleBit:1;
  UINT32                  ENT:1;
  UINT32                  ISP:1;
  UINT32                  NS:1;
  UINT32                  CH:1;
  UINT32                  IOC:1;
  UINT32                  IDT:1;
  UINT32                  RsvdZ1:2;
  UINT32                  BEI:1;
  UINT32                  Type:6;
  UINT32                  RsvdZ2:16;
} TRANSFER_TRB_NORMAL;

//
// 6.4.2.1 Transfer Event TRB: 16 bytes
// A Transfer Event provides the completion status associated with a Transfer TRB. Refer to section 4.11.3.1
// for more information on the use and operation of Transfer Events.
//
typedef struct _EVT_TRB_TRANSFER {
  UINT32                  TRBPtrLo;

  UINT32                  TRBPtrHi;

  UINT32                  Length:24;
  UINT32                  Completecode:8;

  UINT32                  CycleBit:1;
  UINT32                  RsvdZ1:1;
  UINT32                  ED:1;
  UINT32                  RsvdZ2:7;
  UINT32                  Type:6;
  UINT32                  EndpointId:5;
  UINT32                  RsvdZ3:3;
  UINT32                  SlotId:8;
} EVT_TRB_TRANSFER;

//
// 6.4.4.1 Link TRB: 16 bytes
// A Link TRB provides support for non-contiguous TRB Rings.
//
typedef struct _LINK_TRB {
  UINT32                  PtrLo;

  UINT32                  PtrHi;

  UINT32                  RsvdZ1:22;
  UINT32                  InterTarget:10;

  UINT32                  CycleBit:1;
  UINT32                  TC:1;
  UINT32                  RsvdZ2:2;
  UINT32                  CH:1;
  UINT32                  IOC:1;
  UINT32                  RsvdZ3:4;
  UINT32                  Type:6;
  UINT32                  RsvdZ4:16;
} LINK_TRB;

//
// TRB Template: 16 bytes
//
typedef struct _TRB_TEMPLATE {
  UINT32                    Parameter1;

  UINT32                    Parameter2;

  UINT32                    Status;

  UINT32                    CycleBit:1;
  UINT32                    RsvdZ1:9;
  UINT32                    Type:6;
  UINT32                    Control:16;
} TRB_TEMPLATE;

//
// Refer to XHCI 6.5 Event Ring Segment Table: 16 bytes
//
typedef struct _EVENT_RING_SEG_TABLE_ENTRY {
  UINT32                  PtrLo;
  UINT32                  PtrHi;
  UINT32                  RingTrbSize:16;
  UINT32                  RsvdZ1:16;
  UINT32                  RsvdZ2;
} EVENT_RING_SEG_TABLE_ENTRY;

//
// Size: 40 bytes
//
typedef struct _EVENT_RING {
  EFI_PHYSICAL_ADDRESS      ERSTBase;
  EFI_PHYSICAL_ADDRESS      EventRingSeg0;
  UINT32                    TrbNumber;
  EFI_PHYSICAL_ADDRESS      EventRingEnqueue;
  EFI_PHYSICAL_ADDRESS      EventRingDequeue;
  UINT32                    EventRingCCS;
} EVENT_RING;

// Size: 32 bytes
typedef struct _TRANSFER_RING {
  EFI_PHYSICAL_ADDRESS      RingSeg0;
  UINT32                    TrbNumber;
  EFI_PHYSICAL_ADDRESS      RingEnqueue;
  EFI_PHYSICAL_ADDRESS      RingDequeue;
  UINT32                    RingPCS;
} TRANSFER_RING;

//
// Size: 64 bytes
//
typedef struct _DBC_INFO_CONTEXT {
  UINT64        String0DescAddress;
  UINT64        ManufacturerStrDescAddress;
  UINT64        ProductStrDescAddress;
  UINT64        SerialNumberStrDescAddress;
  UINT64        String0Length:8;
  UINT64        ManufacturerStrLength:8;
  UINT64        ProductStrLength:8;
  UINT64        SerialNumberStrLength:8;
  UINT64        RsvdZ1:32;
  UINT64        RsvdZ2;
  UINT64        RsvdZ3;
  UINT64        RsvdZ4;  
} DBC_INFO_CONTEXT;

//
// Debug Capability Context Data Structure: 192 bytes
//
typedef struct _XHC_DC_CONTEXT {
  DBC_INFO_CONTEXT      DbcInfoContext;
  ENDPOINT_CONTEXT_64   EpOutContext;
  ENDPOINT_CONTEXT_64   EpInContext;
} XHC_DC_CONTEXT;

//
// Size: 16 bytes
//
typedef union _TRB {
  TRB_TEMPLATE                TrbTemplate;
  TRANSFER_TRB_NORMAL         TrbNormal;
} TRB;

///
/// USB data transfer direction
///
typedef enum {
  EfiUsbDataIn,
  EfiUsbDataOut,
  EfiUsbNoData
} EFI_USB_DATA_DIRECTION;

//
// URB (Usb Request Block) contains information for all kinds of
// usb requests.
//
typedef struct _URB {
  //
  // Transfer data buffer
  //
  EFI_PHYSICAL_ADDRESS            Data;
  UINT32                          DataLen;

  //
  // Execute result
  //
  UINT32                          Result;
  //
  // Completed data length
  //
  UINT32                          Completed;
  //
  // Tranfer Ring info
  //
  EFI_PHYSICAL_ADDRESS            Ring;
  EFI_PHYSICAL_ADDRESS            Trb;
  BOOLEAN                         Finished;
  EFI_USB_DATA_DIRECTION          Direction;
} URB;

typedef struct _USB3_DEBUG_PORT_INSTANCE {
  UINT8                                   Initialized;

  //
  // The flag indicates debug device is ready
  //
  BOOLEAN                                 DebugSupport;
  
  //
  // The flag indicates debug device is ready
  //
  BOOLEAN                                 Ready;

  //
  // The flag indicates if USB 3.0 ports has been turn off/on power
  //  
  BOOLEAN                                 ChangePortPower;

  //
  // XHCI MMIO Base address
  //
  EFI_PHYSICAL_ADDRESS                    XhciMmioBase;

  //
  // XHCI OP RegisterBase address
  //  
  EFI_PHYSICAL_ADDRESS                    XhciOpRegister;
  
  //
  // XHCI Debug Register Base Address
  //
  EFI_PHYSICAL_ADDRESS                    DebugCapabilityBase;
  
  //
  // XHCI Debug Capability offset
  //
  UINT64                                  DebugCapabilityOffset;  
  
  //
  // XHCI Debug Context Address
  //
  EFI_PHYSICAL_ADDRESS                    DebugCapabilityContext;
  
  //
  // Transfer Ring
  //
  TRANSFER_RING                           TransferRingOut;
  TRANSFER_RING                           TransferRingIn;

  //
  // EventRing
  //
  EVENT_RING                              EventRing;
  
  //
  // URB - Read
  //
  URB                                     UrbOut;

  //
  // URB - Write
  //
  URB                                     UrbIn;

  //
  // The available data length in the following data buffer.
  //
  UINT8                                   DataCount;
  //
  // The data buffer address for data read and poll.
  //
  EFI_PHYSICAL_ADDRESS                    Data;
  //
  // Timter settings
  //
  UINT64                                  TimerFrequency;
  UINT64                                  TimerCycle;
  BOOLEAN                                 TimerCountDown;

} USB3_DEBUG_PORT_HANDLE;

#pragma pack()

/**
  Read XHCI debug register.

 @param  Handle        Debug port handle.
  @param  Offset       The offset of the debug register.

  @return The register content read

**/
UINT32
XhcReadDebugReg (
  IN  USB3_DEBUG_PORT_HANDLE    *Handle,
  IN  UINT32                      Offset
  );

/**
  Set one bit of the debug register while keeping other bits.

  @param  Handle       Debug port handle.
  @param  Offset       The offset of the debug register.
  @param  Bit          The bit mask of the register to set.

**/
VOID
XhcSetDebugRegBit (
  IN USB3_DEBUG_PORT_HANDLE  *Handle,
  IN UINT32                   Offset,
  IN UINT32                   Bit
  );
  
/**
  Write the data to the debug register.

  @param  Handle       Debug port handle.
  @param  Offset       The offset of the debug register.
  @param  Data         The data to write.

**/  
VOID
XhcWriteDebugReg (
  IN USB3_DEBUG_PORT_HANDLE     *Handle,
  IN UINT32                     Offset,
  IN UINT32                     Data
  );

/**
  Discover the USB3 debug device.
  
  @param  Handle                Debug port handle.
  
  @retval RETURN_SUCCESS        The serial device was initialized.
  @retval RETURN_DEVICE_ERROR   The serial device could not be initialized.

**/
RETURN_STATUS
DiscoverUsb3DebugPort(
  USB3_DEBUG_PORT_HANDLE  *Handle
  );
  
/**
  Initialize the Serial Device hardware.
  
  @param  Handle            Debug port handle.

  @retval RETURN_SUCCESS    The serial device was initialized successfully.
  @retval !RETURN_SUCCESS   Error.

**/
RETURN_STATUS
InitializeUsb3DebugPort (
  USB3_DEBUG_PORT_HANDLE  *Handle
  );

/**
  Return XHCI MMIO base address.

**/
EFI_PHYSICAL_ADDRESS
GetXhciBaseAddress (
  VOID
  );

/**
  Verifies if the bit positions specified by a mask are set in a register.

  @param[in, out] Register    UNITN register
  @param[in]      BitMask     32-bit mask

  @return  BOOLEAN  - TRUE  if all bits specified by the mask are enabled.
                    - FALSE even if one of the bits specified by the mask 
                            is not enabled.
**/
BOOLEAN
XhcIsBitSet(
  UINTN   Register, 
  UINT32  BitMask
  );

/**
  Sets bits as per the enabled bit positions in the mask.

  @param[in, out] Register    UINTN register
  @param[in]      BitMask     32-bit mask
**/
VOID
XhcSetR32Bit(
  UINTN   Register, 
  UINT32  BitMask
  );

/**
  Clears bits as per the enabled bit positions in the mask.

  @param[in, out] Register    UINTN register
  @param[in]      BitMask     32-bit mask
**/
VOID
XhcClearR32Bit(
  IN OUT  UINTN  Register, 
  IN      UINT32 BitMask
  );

/**
  Initialize USB3 debug port.
  
  This method invokes various internal functions to facilitate
  detection and initialization of USB3 debug port.

  @retval RETURN_SUCCESS        The serial device was initialized.
**/
RETURN_STATUS
EFIAPI
USB3Initialize (
  VOID
  );

/**
  Return command register value in XHCI controller.

**/
UINT16
GetXhciPciCommand (
  VOID
  );

/**
  Allocate aligned memory for XHC's usage.

  @param  BufferSize      The size, in bytes, of the Buffer.
  
  @return A pointer to the allocated buffer or NULL if allocation fails.

**/
VOID*
AllocateAlignBuffer (
  IN UINTN                    BufferSize
  );

/**
  The real function to initialize USB3 debug port.
  
  This method invokes various internal functions to facilitate
  detection and initialization of USB3 debug port.

  @retval RETURN_SUCCESS        The serial device was initialized.
**/
RETURN_STATUS
EFIAPI
USB3InitializeReal (
  VOID
  );

/**
  Submits bulk transfer to a bulk endpoint of a USB device.

  @param  Handle                The instance of debug device.
  @param  Direction             The direction of data transfer.
  @param  Data                  Array of pointers to the buffers of data to transmit
                                from or receive into.
  @param  DataLength            The lenght of the data buffer.
  @param  Timeout               Indicates the maximum time, in millisecond, which
                                the transfer is allowed to complete.

  @retval EFI_SUCCESS           The transfer was completed successfully.
  @retval EFI_OUT_OF_RESOURCES  The transfer failed due to lack of resource.
  @retval EFI_INVALID_PARAMETER Some parameters are invalid.
  @retval EFI_TIMEOUT           The transfer failed due to timeout.
  @retval EFI_DEVICE_ERROR      The transfer failed due to host controller error.

**/
EFI_STATUS
EFIAPI
XhcDataTransfer (
  IN     USB3_DEBUG_PORT_HANDLE              *Handle,
  IN     EFI_USB_DATA_DIRECTION              Direction,
  IN OUT VOID                                *Data,
  IN OUT UINTN                               *DataLength,
  IN     UINTN                               Timeout
  );

/**
  Check if the timer is timeout.
  
  @param[in] UsbDebugPortHandle  Pointer to USB Debug port handle
  @param[in] Timer               The start timer from the begin.
  @param[in] TimeoutTicker       Ticker number need time out.

  @return TRUE  Timer time out occurs.
  @retval FALSE Timer does not time out.

**/
BOOLEAN
IsTimerTimeout (
  IN USB3_DEBUG_PORT_HANDLE  *UsbDebugPortHandle,
  IN UINT64                  Timer,
  IN UINT64                  TimeoutTicker
  );

#endif //__SERIAL_PORT_LIB_USB__