/*
 * (c) 2015 Purna Chandra Mandal <purna.mandal@microchip.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 *
 * Microchip PIC32MZ[DA] Starter Kit.
 */

#ifndef __PIC32MZDASK_CONFIG_H
#define __PIC32MZDASK_CONFIG_H

/* System Configuration */
#define CONFIG_SYS_TEXT_BASE		0x9d004000 /* .text */
#define CONFIG_DISPLAY_BOARDINFO

/*--------------------------------------------
 * CPU configuration
 */
/* CPU Timer rate */
#define CONFIG_SYS_MIPS_TIMER_FREQ	100000000

/* Cache Configuration */
#define CONFIG_SYS_MIPS_CACHE_MODE	CONF_CM_CACHABLE_NONCOHERENT

/*----------------------------------------------------------------------
 * Memory Layout
 */
#define CONFIG_SYS_SRAM_BASE		0x80000000
#define CONFIG_SYS_SRAM_SIZE		0x00080000 /* 512K */

/* Initial RAM for temporary stack, global data */
#define CONFIG_SYS_INIT_RAM_SIZE	0x10000
#define CONFIG_SYS_INIT_RAM_ADDR	\
	(CONFIG_SYS_SRAM_BASE + CONFIG_SYS_SRAM_SIZE - CONFIG_SYS_INIT_RAM_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR		\
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE - 1)

/* SDRAM Configuration (for final code, data, stack, heap) */
#define CONFIG_SYS_SDRAM_BASE		0x88000000
#define CONFIG_SYS_MALLOC_LEN		(256 << 10)
#define CONFIG_SYS_BOOTPARAMS_LEN	(4 << 10)
#define CONFIG_STACKSIZE		(4 << 10) /* regular stack */

#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN		(192 << 10)

#define CONFIG_SYS_LOAD_ADDR		0x88500000 /* default load address */
#define CONFIG_SYS_ENV_ADDR		0x88300000
#define CONFIG_SYS_FDT_ADDR		0x89d00000

/* Memory Test */
#define CONFIG_SYS_MEMTEST_START	0x88000000
#define CONFIG_SYS_MEMTEST_END		0x88080000

/*----------------------------------------------------------------------
 * Commands
 */
#define CONFIG_SYS_LONGHELP		/* undef to save memory */
#define CONFIG_CMD_CLK

/*-------------------------------------------------
 * FLASH configuration
 */
#define CONFIG_SYS_NO_FLASH

/*------------------------------------------------------------
 * Console Configuration
 */
#define CONFIG_BAUDRATE			115200
#define CONFIG_SYS_CBSIZE		1024 /* Console I/O Buffer Size   */
#define CONFIG_SYS_MAXARGS		16   /* max number of command args*/
#define CONFIG_SYS_PBSIZE		\
		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_CMDLINE_EDITING		1

/*-----------------------------------------------------------------------
 * Networking Configuration
 */
#define CONFIG_MII
#define CONFIG_PHY_SMSC
#define CONFIG_SYS_RX_ETH_BUFFER	8
#define CONFIG_NET_RETRY_COUNT		20
#define CONFIG_ARP_TIMEOUT		500 /* millisec */

#define CONFIG_CMD_MII

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Handover flattened device tree (dtb file) to Linux kernel
 */
#define CONFIG_OF_LIBFDT	1

/*-----------------------------------------------------------------------
 * SDHC Configuration
 */
#define CONFIG_SDHCI
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_CMD_MMC

/*-----------------------------------------------------------------------
 * File System Configuration
 */
/* FAT FS */
#define CONFIG_DOS_PARTITION
#define CONFIG_PARTITION_UUIDS
#define CONFIG_SUPPORT_VFAT
#define CONFIG_FS_FAT
#define CONFIG_FAT_WRITE
#define CONFIG_CMD_FS_GENERIC
#define CONFIG_CMD_PART
#define CONFIG_CMD_FAT

/* EXT4 FS */
#define CONFIG_FS_EXT4
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_EXT4
#define CONFIG_CMD_EXT4_WRITE

/* -------------------------------------------------
 * Environment
 */
#define CONFIG_ENV_IS_NOWHERE	1
#define CONFIG_ENV_SIZE		0x4000

/* ---------------------------------------------------------------------
 * Board boot configuration
 */
#define CONFIG_TIMESTAMP	/* Print image info with timestamp */
#define CONFIG_BOOTDELAY	5

#define MEM_LAYOUT_ENV_SETTINGS					\
	"kernel_addr_r="__stringify(CONFIG_SYS_LOAD_ADDR)"\0"	\
	"fdt_addr_r="__stringify(CONFIG_SYS_FDT_ADDR)"\0"	\
	"scriptaddr="__stringify(CONFIG_SYS_ENV_ADDR)"\0"

#define CONFIG_LEGACY_BOOTCMD_ENV					\
	"legacy_bootcmd= "						\
		"if load mmc 0 ${scriptaddr} uEnv.txt; then "		\
			"env import -tr ${scriptaddr} ${filesize}; "	\
			"if test -n \"${bootcmd_uenv}\" ; then "	\
				"echo Running bootcmd_uenv ...; "	\
				"run bootcmd_uenv; "			\
			"fi; "						\
		"fi; \0"

#define BOOT_TARGET_DEVICES(func)	\
	func(MMC, mmc, 0)		\
	func(DHCP, dhcp, na)

#include <config_distro_bootcmd.h>

#define CONFIG_EXTRA_ENV_SETTINGS	\
	MEM_LAYOUT_ENV_SETTINGS		\
	CONFIG_LEGACY_BOOTCMD_ENV	\
	BOOTENV

#undef CONFIG_BOOTCOMMAND
#define CONFIG_BOOTCOMMAND	"run distro_bootcmd || run legacy_bootcmd"

#endif	/* __PIC32MZDASK_CONFIG_H */