/*
 * Copyright (C) 2007 Freescale Semiconductor, Inc.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License version 2 as published
 * by the Free Software Foundation.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 */
#define CONFIG_E300		1	/* E300 family */
#define CONFIG_QE		1	/* Has QE */
#define CONFIG_MPC83xx		1	/* MPC83xx family */
#define CONFIG_MPC832x		1	/* MPC832x CPU specific */

#define	CONFIG_SYS_TEXT_BASE	0xFE000000

#define CONFIG_PCI		1

/*
 * System Clock Setup
 */
#define CONFIG_83XX_CLKIN	66666667	/* in Hz */

#ifndef CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
#endif

/*
 * Hardware Reset Configuration Word
 */
#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
	HRCWL_DDR_TO_SCB_CLK_2X1 |\
	HRCWL_VCO_1X2 |\
	HRCWL_CSB_TO_CLKIN_2X1 |\
	HRCWL_CORE_TO_CSB_2_5X1 |\
	HRCWL_CE_PLL_VCO_DIV_2 |\
	HRCWL_CE_PLL_DIV_1X1 |\
	HRCWL_CE_TO_PLL_1X3)

#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_PCI_HOST |\
	HRCWH_PCI1_ARBITER_ENABLE |\
	HRCWH_CORE_ENABLE |\
	HRCWH_FROM_0X00000100 |\
	HRCWH_BOOTSEQ_DISABLE |\
	HRCWH_SW_WATCHDOG_DISABLE |\
	HRCWH_ROM_LOC_LOCAL_16BIT |\
	HRCWH_BIG_ENDIAN |\
	HRCWH_LALE_NORMAL)

/*
 * System IO Config
 */
#define CONFIG_SYS_SICRL		0x00000000

/*
 * IMMR new address
 */
#define CONFIG_SYS_IMMR		0xE0000000

/*
 * System performance
 */
#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
#define CONFIG_SYS_SPCR_OPT		1	/* (0-1) Optimize transactions between  CSB and the SEC and QUICC Engine block */

/*
 * DDR Setup
 */
#define CONFIG_SYS_DDR_BASE		0x00000000	/* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDRCDR		0x73000002	/* DDR II voltage is 1.8V */

#undef CONFIG_SPD_EEPROM
#if defined(CONFIG_SPD_EEPROM)
/* Determine DDR configuration from I2C interface
 */
#define SPD_EEPROM_ADDRESS	0x51	/* DDR SODIMM */
#else
/* Manually set up DDR parameters
 */
#define CONFIG_SYS_DDR_SIZE		64	/* MB */
#define CONFIG_SYS_DDR_CS0_CONFIG	( CSCONFIG_EN \
				| CSCONFIG_ODT_WR_ACS \
				| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9 )
				/* 0x80010101 */
#define CONFIG_SYS_DDR_TIMING_0	( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
				| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
				| ( 0 << TIMING_CFG0_RRT_SHIFT ) \
				| ( 0 << TIMING_CFG0_WWT_SHIFT ) \
				| ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
				| ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
				| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
				| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
				/* 0x00220802 */
#define CONFIG_SYS_DDR_TIMING_1	( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
				| ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
				| ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \
				| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
				| ( 3 << TIMING_CFG1_REFREC_SHIFT ) \
				| ( 2 << TIMING_CFG1_WRREC_SHIFT ) \
				| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
				| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
				/* 0x26253222 */
#define CONFIG_SYS_DDR_TIMING_2	( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
				| (31 << TIMING_CFG2_CPO_SHIFT ) \
				| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
				| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
				| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
				| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
				| ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
				/* 0x1f9048c7 */
#define CONFIG_SYS_DDR_TIMING_3	0x00000000
#define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
				/* 0x02000000 */
#define CONFIG_SYS_DDR_MODE		( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
				| ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
				/* 0x44480232 */
#define CONFIG_SYS_DDR_MODE2		0x8000c000
#define CONFIG_SYS_DDR_INTERVAL	( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
				| ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
				/* 0x03200064 */
#define CONFIG_SYS_DDR_CS0_BNDS	0x00000003
#define CONFIG_SYS_DDR_SDRAM_CFG	( SDRAM_CFG_SREN \
				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
				| SDRAM_CFG_32_BE )
				/* 0x43080000 */
#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
#endif

/*
 * Memory test
 */
#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START	0x00030000	/* memtest region */
#define CONFIG_SYS_MEMTEST_END		0x03f00000

/*
 * The reserved memory
 */
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef  CONFIG_SYS_RAMBOOT
#endif

/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */

/*
 * Initial RAM Base Address Setup
 */
#define CONFIG_SYS_INIT_RAM_LOCK	1
#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000	/* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE	0x1000		/* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

/*
 * Local Bus Configuration & Clock Setup
 */
#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR		0x00000000

/*
 * FLASH on the Local Bus
 */
#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER	/* use the CFI driver */
#define CONFIG_SYS_FLASH_BASE		0xFE000000	/* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE		16	/* FLASH size is 16M */
#define CONFIG_SYS_FLASH_PROTECTION	1		/* Use h/w Flash protection. */

#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE	/* Window base at flash base */
#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000018	/* 32MB window size */

#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE |	/* Flash Base address */ \
			(2 << BR_PS_SHIFT) |	/* 16 bit port size */ \
			BR_V)			/* valid */
#define CONFIG_SYS_OR0_PRELIM		0xfe006ff7	/* 16MB Flash size */

#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	128		/* sectors per device */

#undef CONFIG_SYS_FLASH_CHECKSUM

/*
 * SDRAM on the Local Bus
 */
#undef CONFIG_SYS_LB_SDRAM		/* The board has not SRDAM on local bus */

#ifdef CONFIG_SYS_LB_SDRAM
#define CONFIG_SYS_LBC_SDRAM_BASE	0xF0000000	/* SDRAM base address */
#define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */

#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_LBC_SDRAM_BASE
#define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000019	/* 64MB */

/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */
/*
 * Base Register 2 and Option Register 2 configure SDRAM.
 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
 *
 * For BR2, need:
 *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
 *    port size = 32-bits = BR2[19:20] = 11
 *    no parity checking = BR2[21:22] = 00
 *    SDRAM for MSEL = BR2[24:26] = 011
 *    Valid = BR[31] = 1
 *
 * 0    4    8    12   16   20   24   28
 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
 *
 * CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
 * the top 17 bits of BR2.
 */

#define CONFIG_SYS_BR2_PRELIM	0xf0001861	/*Port size=32bit, MSEL=SDRAM */

/*
 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
 *
 * For OR2, need:
 *    64MB mask for AM, OR2[0:7] = 1111 1100
 *                 XAM, OR2[17:18] = 11
 *    9 columns OR2[19-21] = 010
 *    13 rows   OR2[23-25] = 100
 *    EAD set for extra time OR[31] = 1
 *
 * 0    4    8    12   16   20   24   28
 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
 */

#define CONFIG_SYS_OR2_PRELIM	0xfc006901

#define CONFIG_SYS_LBC_LSRT	0x32000000	/* LB sdram refresh timer, about 6us */
#define CONFIG_SYS_LBC_MRTPR	0x20000000	/* LB refresh timer prescal, 266MHz/32 */

#define CONFIG_SYS_LBC_LSDMR_COMMON	0x0063b723

#endif

/*
 * Windows to access PIB via local bus
 */
#define CONFIG_SYS_LBLAWBAR3_PRELIM	0xf8008000	/* windows base 0xf8008000 */
#define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000000f	/* windows size 64KB */

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX	1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE  \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)

#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
#define CONFIG_AUTO_COMPLETE		/* add autocompletion support   */
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
#ifdef CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif

/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT	1
#define CONFIG_OF_BOARD_SETUP	1
#define CONFIG_OF_STDOUT_VIA_ALIAS	1

/* I2C */
#define CONFIG_HARD_I2C		/* I2C with hardware support */
#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
#define CONFIG_FSL_I2C
#define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE	0x7F
#define CONFIG_SYS_I2C_NOPROBES	{0x51}	/* Don't probe these addrs */
#define CONFIG_SYS_I2C_OFFSET	0x3000

/*
 * Config on-board EEPROM
 */
#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI1_IO_BASE		0xd0000000
#define CONFIG_SYS_PCI1_IO_PHYS		CONFIG_SYS_PCI1_IO_BASE
#define CONFIG_SYS_PCI1_IO_SIZE		0x04000000	/* 64M */

#ifdef CONFIG_PCI
#define CONFIG_PCI_SKIP_HOST_BRIDGE
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP		/* do pci plug-and-play */

#undef CONFIG_EEPRO100
#undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */

#endif	/* CONFIG_PCI */


#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI	1
#endif

/*
 * QE UEC ethernet configuration
 */
#define CONFIG_UEC_ETH
#define CONFIG_ETHPRIME		"UEC0"

#define CONFIG_UEC_ETH1		/* ETH3 */

#ifdef CONFIG_UEC_ETH1
#define CONFIG_SYS_UEC1_UCC_NUM	2	/* UCC3 */
#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK9
#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK10
#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR	4
#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_MII
#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
#endif

#define CONFIG_UEC_ETH2		/* ETH4 */

#ifdef CONFIG_UEC_ETH2
#define CONFIG_SYS_UEC2_UCC_NUM	1	/* UCC2 */
#define CONFIG_SYS_UEC2_RX_CLK		QE_CLK16
#define CONFIG_SYS_UEC2_TX_CLK		QE_CLK3
#define CONFIG_SYS_UEC2_ETH_TYPE	FAST_ETH
#define CONFIG_SYS_UEC2_PHY_ADDR	0
#define CONFIG_SYS_UEC2_INTERFACE_TYPE	PHY_INTERFACE_MODE_MII
#define CONFIG_SYS_UEC2_INTERFACE_SPEED	100
#endif

/*
 * Environment
 */
#ifndef CONFIG_SYS_RAMBOOT
	#define CONFIG_ENV_IS_IN_FLASH	1
	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
	#define CONFIG_ENV_SECT_SIZE	0x20000
	#define CONFIG_ENV_SIZE		0x2000
#else
	#define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE		0x2000
#endif

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ASKENV

#if defined(CONFIG_PCI)
	#define CONFIG_CMD_PCI
#endif
#if defined(CONFIG_SYS_RAMBOOT)
	#undef CONFIG_CMD_SAVEENV
	#undef CONFIG_CMD_LOADS
#endif

#undef CONFIG_WATCHDOG		/* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP		/* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR		0x2000000	/* default load address */
#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt */

#if (CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size */
#else
	#define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
#endif

#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 256 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ		(256 << 20)	/* Initial Memory map for Linux */

/*
 * Core HID Setup
 */
#define CONFIG_SYS_HID0_INIT	0x000000000
#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
				 HID0_ENABLE_INSTRUCTION_CACHE)
#define CONFIG_SYS_HID2		HID2_HBE

/*
 * MMU Setup
 */
#define CONFIG_HIGH_BATS	1	/* High BATs supported */

/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U

/* IMMRBAR & PCI IO: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_10 | \
			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U

/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U

#define CONFIG_SYS_IBAT3L	(0)
#define CONFIG_SYS_IBAT3U	(0)
#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U

/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U

#ifdef CONFIG_PCI
/* PCI MEM space: cacheable */
#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
/* PCI MMIO space: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_PCI1_MMIO_PHYS | BATL_PP_10 | \
			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
#else
#define CONFIG_SYS_IBAT5L	(0)
#define CONFIG_SYS_IBAT5U	(0)
#define CONFIG_SYS_IBAT6L	(0)
#define CONFIG_SYS_IBAT6U	(0)
#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
#endif

/* Nothing in BAT7 */
#define CONFIG_SYS_IBAT7L	(0)
#define CONFIG_SYS_IBAT7U	(0)
#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U

#if (CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
#endif

/*
 * Environment Configuration
 */
#define CONFIG_ENV_OVERWRITE

#define CONFIG_HAS_ETH0				/* add support for "ethaddr" */
#define CONFIG_HAS_ETH1				/* add support for "eth1addr" */

/* use mac_read_from_eeprom() to read ethaddr from I2C EEPROM (see CONFIG_SYS_I2C_EEPROM) */
#define CONFIG_SYS_I2C_MAC_OFFSET	0x7f00	/* MAC address offset in I2C EEPROM */

#define CONFIG_NETDEV		eth1

#define CONFIG_HOSTNAME		mpc8323erdb
#define CONFIG_ROOTPATH		/nfsroot
#define CONFIG_RAMDISKFILE	rootfs.ext2.gz.uboot
#define CONFIG_BOOTFILE		uImage
#define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */
#define CONFIG_FDTFILE		mpc832x_rdb.dtb

#define CONFIG_LOADADDR		800000	/* default location for tftp and bootm */
#define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
#define CONFIG_BAUDRATE		115200

#define XMK_STR(x)	#x
#define MK_STR(x)	XMK_STR(x)

#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=" MK_STR(CONFIG_NETDEV) "\0"				\
	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
	"tftpflash=tftp $loadaddr $uboot;"				\
		"protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
		"erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "		\
		"cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; "	\
		"protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "		\
		"cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0"	\
	"fdtaddr=780000\0"						\
	"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0"				\
	"ramdiskaddr=1000000\0"						\
	"ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0"			\
	"console=ttyS0\0"						\
	"setbootargs=setenv bootargs "					\
		"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
	"setipargs=setenv bootargs nfsroot=$serverip:$rootpath "	\
		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
		"root=$rootdev rw console=$console,$baudrate $othbootargs\0"

#define CONFIG_NFSBOOTCOMMAND						\
	"setenv rootdev /dev/nfs;"					\
	"run setbootargs;"						\
	"run setipargs;"						\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND						\
	"setenv rootdev /dev/ram;"					\
	"run setbootargs;"						\
	"tftp $ramdiskaddr $ramdiskfile;"				\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

#undef MK_STR
#undef XMK_STR

#endif	/* __CONFIG_H */