/*
 * (C) Copyright 2007-2008
 * Stelian Pop <stelian@popies.net>
 * Lead Tech Design <www.leadtechdesign.com>
 *
 * Configuation settings for the AT91SAM9263EK board.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * SoC must be defined first, before hardware.h is included.
 * In this case SoC is defined in boards.cfg.
 */
#include <asm/hardware.h>

#ifndef CONFIG_SYS_USE_BOOT_NORFLASH
#define CONFIG_SYS_TEXT_BASE		0x21F00000
#else
#define CONFIG_SYS_TEXT_BASE		0x0000000
#endif

/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_MAIN_CLOCK	16367660 /* 16.367 MHz crystal */
#define CONFIG_SYS_AT91_SLOW_CLOCK	32768

#define CONFIG_AT91SAM9263EK	1	/* It's an AT91SAM9263EK Board */

#define CONFIG_ARCH_CPU_INIT

#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs	*/
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG	1

#ifndef CONFIG_SYS_USE_BOOT_NORFLASH
#define CONFIG_SKIP_LOWLEVEL_INIT
#else
#define CONFIG_SYS_USE_NORFLASH
#endif

#define CONFIG_BOARD_EARLY_INIT_F

#define CONFIG_DISPLAY_CPUINFO

#define CONFIG_CMD_BOOTZ
#define CONFIG_OF_LIBFDT

/*
 * Hardware drivers
 */
#define CONFIG_ATMEL_LEGACY
#define CONFIG_AT91_GPIO		1
#define CONFIG_AT91_GPIO_PULLUP		1

/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
#define CONFIG_USART_ID			ATMEL_ID_SYS
#define CONFIG_BAUDRATE			115200

/* LCD */
#define CONFIG_LCD			1
#define LCD_BPP				LCD_COLOR8
#define CONFIG_LCD_LOGO			1
#undef LCD_TEST_PATTERN
#define CONFIG_LCD_INFO			1
#define CONFIG_LCD_INFO_BELOW_LOGO	1
#define CONFIG_SYS_WHITE_ON_BLACK	1
#define CONFIG_ATMEL_LCD		1
#define CONFIG_ATMEL_LCD_BGR555		1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1

/* LED */
#define CONFIG_AT91_LED
#define	CONFIG_RED_LED		AT91_PIN_PB7	/* the power led */
#define	CONFIG_GREEN_LED	AT91_PIN_PB8	/* the user1 led */
#define	CONFIG_YELLOW_LED	AT91_PIN_PC29	/* the user2 led */

#define CONFIG_BOOTDELAY	3

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE	1
#define CONFIG_BOOTP_BOOTPATH		1
#define CONFIG_BOOTP_GATEWAY		1
#define CONFIG_BOOTP_HOSTNAME		1

/*
 * Command line configuration.
 */
#include <config_cmd_default.h>
#undef CONFIG_CMD_BDI
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_SOURCE

#define CONFIG_CMD_PING		1
#define CONFIG_CMD_DHCP		1
#define CONFIG_CMD_NAND		1
#define CONFIG_CMD_USB		1

/* SDRAM */
#define CONFIG_NR_DRAM_BANKS		1
#define CONFIG_SYS_SDRAM_BASE		ATMEL_BASE_CS1
#define CONFIG_SYS_SDRAM_SIZE		0x04000000

#define CONFIG_SYS_INIT_SP_ADDR \
	(ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)

/* DataFlash */
#define CONFIG_ATMEL_DATAFLASH_SPI
#define CONFIG_HAS_DATAFLASH		1
#define CONFIG_SYS_SPI_WRITE_TOUT		(5*CONFIG_SYS_HZ)
#define CONFIG_SYS_MAX_DATAFLASH_BANKS		1
#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0	0xC0000000	/* CS0 */
#define AT91_SPI_CLK			15000000
#define DATAFLASH_TCSS			(0x1a << 16)
#define DATAFLASH_TCHS			(0x1 << 24)

/* NOR flash, if populated */
#ifdef CONFIG_SYS_USE_NORFLASH
#define CONFIG_SYS_FLASH_CFI			1
#define CONFIG_FLASH_CFI_DRIVER			1
#define PHYS_FLASH_1				0x10000000
#define CONFIG_SYS_FLASH_BASE			PHYS_FLASH_1
#define CONFIG_SYS_MAX_FLASH_SECT		256
#define CONFIG_SYS_MAX_FLASH_BANKS		1

#define CONFIG_SYS_MONITOR_SEC	1:0-3
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN	(256 << 10)
#define CONFIG_ENV_IS_IN_FLASH	1
#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x007E0000)
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR - CONFIG_ENV_SIZE)

/* Address and size of Primary Environment Sector */
#define CONFIG_ENV_SIZE		0x10000

#define CONFIG_EXTRA_ENV_SETTINGS	\
	"monitor_base=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0" \
	"update=" \
		"protect off ${monitor_base} +${filesize};" \
		"erase ${monitor_base} +${filesize};" \
		"cp.b ${fileaddr} ${monitor_base} ${filesize};" \
		"protect on ${monitor_base} +${filesize}\0"

#ifndef CONFIG_SKIP_LOWLEVEL_INIT
#define MASTER_PLL_MUL		171
#define MASTER_PLL_DIV		14
#define MASTER_PLL_OUT		3

/* clocks */
#define CONFIG_SYS_MOR_VAL						\
		(AT91_PMC_MOR_MOSCEN | AT91_PMC_MOR_OSCOUNT(255))
#define CONFIG_SYS_PLLAR_VAL					\
	(AT91_PMC_PLLAR_29 |					\
	AT91_PMC_PLLXR_OUT(MASTER_PLL_OUT) |			\
	AT91_PMC_PLLXR_PLLCOUNT(63) |				\
	AT91_PMC_PLLXR_MUL(MASTER_PLL_MUL - 1) | 		\
	AT91_PMC_PLLXR_DIV(MASTER_PLL_DIV))

/* PCK/2 = MCK Master Clock from PLLA */
#define	CONFIG_SYS_MCKR1_VAL		\
	(AT91_PMC_MCKR_CSS_SLOW | AT91_PMC_MCKR_PRES_1 |	\
	 AT91_PMC_MCKR_MDIV_2)

/* PCK/2 = MCK Master Clock from PLLA */
#define	CONFIG_SYS_MCKR2_VAL		\
	(AT91_PMC_MCKR_CSS_PLLA | AT91_PMC_MCKR_PRES_1 | 	\
	AT91_PMC_MCKR_MDIV_2)

/* define PDC[31:16] as DATA[31:16] */
#define CONFIG_SYS_PIOD_PDR_VAL1	0xFFFF0000
/* no pull-up for D[31:16] */
#define CONFIG_SYS_PIOD_PPUDR_VAL	0xFFFF0000
/* EBI0_CSA, CS1 SDRAM, CS3 NAND Flash, 3.3V memories */
#define CONFIG_SYS_MATRIX_EBICSA_VAL					\
	(AT91_MATRIX_CSA_DBPUC | AT91_MATRIX_CSA_VDDIOMSEL_3_3V |	\
	 AT91_MATRIX_CSA_EBI_CS1A)

/* SDRAM */
/* SDRAMC_MR Mode register */
#define CONFIG_SYS_SDRC_MR_VAL1		0
/* SDRAMC_TR - Refresh Timer register */
#define CONFIG_SYS_SDRC_TR_VAL1		0x13C
/* SDRAMC_CR - Configuration register*/
#define CONFIG_SYS_SDRC_CR_VAL							\
		(AT91_SDRAMC_NC_9 |						\
		 AT91_SDRAMC_NR_13 |						\
		 AT91_SDRAMC_NB_4 |						\
		 AT91_SDRAMC_CAS_3 |						\
		 AT91_SDRAMC_DBW_32 |						\
		 (1 <<  8) |		/* Write Recovery Delay */		\
		 (7 << 12) |		/* Row Cycle Delay */			\
		 (2 << 16) |		/* Row Precharge Delay */		\
		 (2 << 20) |		/* Row to Column Delay */		\
		 (5 << 24) |		/* Active to Precharge Delay */		\
		 (1 << 28))		/* Exit Self Refresh to Active Delay */

/* Memory Device Register -> SDRAM */
#define CONFIG_SYS_SDRC_MDR_VAL		AT91_SDRAMC_MD_SDRAM
#define CONFIG_SYS_SDRC_MR_VAL2		AT91_SDRAMC_MODE_PRECHARGE
#define CONFIG_SYS_SDRAM_VAL1		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRC_MR_VAL3		AT91_SDRAMC_MODE_REFRESH
#define CONFIG_SYS_SDRAM_VAL2		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRAM_VAL3		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRAM_VAL4		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRAM_VAL5		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRAM_VAL6		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRAM_VAL7		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRAM_VAL8		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRAM_VAL9		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRC_MR_VAL4		AT91_SDRAMC_MODE_LMR
#define CONFIG_SYS_SDRAM_VAL10		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRC_MR_VAL5		AT91_SDRAMC_MODE_NORMAL
#define CONFIG_SYS_SDRAM_VAL11		0		/* SDRAM_BASE */
#define CONFIG_SYS_SDRC_TR_VAL2		1200		/* SDRAM_TR */
#define CONFIG_SYS_SDRAM_VAL12		0		/* SDRAM_BASE */

/* setup SMC0, CS0 (NOR Flash) - 16-bit, 15 WS */
#define CONFIG_SYS_SMC0_SETUP0_VAL				\
	(AT91_SMC_SETUP_NWE(10) | AT91_SMC_SETUP_NCS_WR(10) |	\
	 AT91_SMC_SETUP_NRD(10) | AT91_SMC_SETUP_NCS_RD(10))
#define CONFIG_SYS_SMC0_PULSE0_VAL				\
	(AT91_SMC_PULSE_NWE(11) | AT91_SMC_PULSE_NCS_WR(11) |	\
	 AT91_SMC_PULSE_NRD(11) | AT91_SMC_PULSE_NCS_RD(11))
#define CONFIG_SYS_SMC0_CYCLE0_VAL	\
	(AT91_SMC_CYCLE_NWE(22) | AT91_SMC_CYCLE_NRD(22))
#define CONFIG_SYS_SMC0_MODE0_VAL				\
	(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |		\
	 AT91_SMC_MODE_DBW_16 |					\
	 AT91_SMC_MODE_TDF | AT91_SMC_MODE_TDF_CYCLE(6))

/* user reset enable */
#define CONFIG_SYS_RSTC_RMR_VAL			\
		(AT91_RSTC_KEY |		\
		AT91_RSTC_MR_URSTEN |		\
		AT91_RSTC_MR_ERSTL(15))

/* Disable Watchdog */
#define CONFIG_SYS_WDTC_WDMR_VAL				\
		(AT91_WDT_MR_WDIDLEHLT | AT91_WDT_MR_WDDBGHLT |	\
		 AT91_WDT_MR_WDV(0xfff) |			\
		 AT91_WDT_MR_WDDIS |				\
		 AT91_WDT_MR_WDD(0xfff))

#endif

#else
#define CONFIG_SYS_NO_FLASH			1
#endif

/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE		1
#define CONFIG_SYS_NAND_BASE			ATMEL_BASE_CS3
#define CONFIG_SYS_NAND_DBW_8			1
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE		(1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE		(1 << 22)
#define CONFIG_SYS_NAND_ENABLE_PIN		AT91_PIN_PD15
#define CONFIG_SYS_NAND_READY_PIN		AT91_PIN_PA22
#endif

/* Ethernet */
#define CONFIG_MACB			1
#define CONFIG_RMII			1
#define CONFIG_NET_RETRY_COUNT		20
#define CONFIG_RESET_PHY_R		1

/* USB */
#define CONFIG_USB_ATMEL
#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW		1
#define CONFIG_DOS_PARTITION		1
#define CONFIG_SYS_USB_OHCI_CPU_INIT		1
#define CONFIG_SYS_USB_OHCI_REGS_BASE		0x00a00000	/* AT91SAM9263_UHP_BASE */
#define CONFIG_SYS_USB_OHCI_SLOT_NAME		"at91sam9263"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
#define CONFIG_USB_STORAGE		1
#define CONFIG_CMD_FAT			1

#define CONFIG_SYS_LOAD_ADDR			0x22000000	/* load address */

#define CONFIG_SYS_MEMTEST_START		CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END			0x23e00000

#ifdef CONFIG_SYS_USE_DATAFLASH

/* bootstrap + u-boot + env + linux in dataflash on CS0 */
#define CONFIG_ENV_IS_IN_DATAFLASH	1
#define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400)
#define CONFIG_ENV_OFFSET		0x4200
#define CONFIG_ENV_ADDR		(CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET)
#define CONFIG_ENV_SIZE		0x4200
#define CONFIG_BOOTCOMMAND	"cp.b 0xC0084000 0x22000000 0x210000; bootm"
#define CONFIG_BOOTARGS		"console=ttyS0,115200 " \
				"root=/dev/mtdblock0 " \
				"mtdparts=atmel_nand:-(root) "\
				"rw rootfstype=jffs2"

#elif CONFIG_SYS_USE_NANDFLASH

/* bootstrap + u-boot + env + linux in nandflash */
#define CONFIG_ENV_IS_IN_NAND		1
#define CONFIG_ENV_OFFSET		0xc0000
#define CONFIG_ENV_OFFSET_REDUND	0x100000
#define CONFIG_ENV_SIZE		0x20000		/* 1 sector = 128 kB */
#define CONFIG_BOOTCOMMAND	"nand read 0x22000000 0x200000 0x300000; bootm"
#define CONFIG_BOOTARGS							\
	"console=ttyS0,115200 earlyprintk "				\
	"mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,"		\
	"256k(env),256k(env_redundant),256k(spare),"			\
	"512k(dtb),6M(kernel)ro,-(rootfs) "				\
	"root=/dev/mtdblock7 rw rootfstype=jffs2"
#endif

#define CONFIG_SYS_PROMPT		"U-Boot> "
#define CONFIG_SYS_CBSIZE		256
#define CONFIG_SYS_MAXARGS		16
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP		1
#define CONFIG_CMDLINE_EDITING		1
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_HUSH_PARSER

/*
 * Size of malloc() pool
 */
#define CONFIG_SYS_MALLOC_LEN	ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)

#endif