.. SPDX-License-Identifier: GPL-2.0+

U-Boot for Amlogic P200 (S905)
==============================

P200 is a reference board manufactured by Amlogic with the following specification:

 - Amlogic S905 ARM Cortex-A53 quad-core SoC @ 1.5GHz
 - ARM Mali 450 GPU
 - 2GB DDR3 SDRAM
 - Gigabit Ethernet
 - HDMI 2.0 4K/60Hz display
 - 2x USB 2.0 Host
 - eMMC, microSD
 - Infrared receiver
 - SDIO WiFi Module
 - CVBS + Stereo Audio Jack

Schematics are available from Amlogic on demand.

U-Boot Compilation
------------------

.. code-block:: bash

    $ export CROSS_COMPILE=aarch64-none-elf-
    $ make p200_defconfig
    $ make

U-Boot Signing with Pre-Built FIP repo
--------------------------------------

.. code-block:: bash

    $ git clone https://github.com/LibreELEC/amlogic-boot-fip --depth=1
    $ cd amlogic-boot-fip
    $ mkdir my-output-dir
    $ ./build-fip.sh p200 /path/to/u-boot/u-boot.bin my-output-dir

U-Boot Manual Signing
---------------------

Amlogic does not provide sources for the firmware and tools needed to create a bootloader
image but sources have been shared by Linux development contractor, Baylibre:

.. code-block:: bash

    $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
    $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
    $ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
    $ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
    $ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
    $ git clone https://github.com/BayLibre/u-boot.git -b n-amlogic-openlinux-20170606 amlogic-u-boot
    $ cd amlogic-u-boot
    $ make gxb_p200_v1_defconfig
    $ make
    $ export FIPDIR=$PWD/fip

Go back to the mainline U-Boot source tree then:

.. code-block:: bash

    $ mkdir fip

    $ cp $FIPDIR/gxb/bl2.bin fip/
    $ cp $FIPDIR/gxb/acs.bin fip/
    $ cp $FIPDIR/gxb/bl21.bin fip/
    $ cp $FIPDIR/gxb/bl30.bin fip/
    $ cp $FIPDIR/gxb/bl301.bin fip/
    $ cp $FIPDIR/gxb/bl31.img fip/
    $ cp u-boot.bin fip/bl33.bin
    $ wget https://github.com/LibreELEC/amlogic-boot-fip/raw/master/nanopi-k2/bl1.bin.hardkernel fip/bl1.bin.hardkernel
    $ chmod +x fip/bl1.bin.hardkernel
    $ wget https://github.com/LibreELEC/amlogic-boot-fip/raw/master/nanopi-k2/aml_chksum fip/aml_chksum
    $ chmod +x fip/aml_chksum

    $ $FIPDIR/blx_fix.sh \
              fip/bl30.bin \
              fip/zero_tmp \
              fip/bl30_zero.bin \
              fip/bl301.bin \
              fip/bl301_zero.bin \
              fip/bl30_new.bin \
              bl30

    $ python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0

    $ $FIPDIR/blx_fix.sh \
              fip/bl2_acs.bin \
              fip/zero_tmp \
              fip/bl2_zero.bin \
              fip/bl21.bin \
              fip/bl21_zero.bin \
              fip/bl2_new.bin \
              bl2

    $ $FIPDIR/fip_create --bl30 fip/bl30_new.bin \
                         --bl31 fip/bl31.img \
                         --bl33 fip/bl33.bin \
                         fip/fip.bin

    $ cat fip/bl2_new.bin fip/fip.bin >fip/boot_new.bin

    $ $FIPDIR/gxb/aml_encrypt_gxb --bootsig \
                                  --input fip/boot_new.bin \
                                  --output fip/u-boot.bin

and then write the image to SD with:

.. code-block:: bash

    $ DEV=/dev/boot_device
    $ dd if=fip/u-boot.bin of=fip/u-boot.bin.gxbb bs=512 conv=fsync
    $ dd if=fip/u-boot.bin of=fip/u-boot.bin.gxbb bs=512 seek=9 skip=8 count=87 conv=fsync,notrunc
    $ dd if=/dev/zero of=fip/u-boot.bin.gxbb bs=512 seek=8 count=1 conv=fsync,notrunc
    $ dd if=bl1.bin.hardkernel of=fip/u-boot.bin.gxbb bs=512 seek=2 skip=2 count=1 conv=fsync,notrunc
    $ ./aml_chksum fip/u-boot.bin.gxbb
    $ dd if=fip/u-boot.gxbb of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
    $ dd if=fip/u-boot.gxbb of=$DEV conv=fsync,notrunc bs=1 count=440