/*
 * Copyright 2016 Toradex AG
 *
 * Configuration settings for the Colibri iMX7 module.
 *
 * based on mx7dsabresd.h:
 * Copyright (C) 2015 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __COLIBRI_IMX7_CONFIG_H
#define __COLIBRI_IMX7_CONFIG_H

#include "mx7_common.h"

#define CONFIG_SYS_THUMB_BUILD

/*#define CONFIG_DBG_MONITOR*/
#define PHYS_SDRAM_SIZE			SZ_512M

#define CONFIG_DISPLAY_BOARDINFO_LATE	/* Calls show_board_info() */

#define CONFIG_ENV_VARS_UBOOT_CONFIG
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(32 * SZ_1M)

#define CONFIG_CMD_BMODE

/* Network */
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define CONFIG_FEC_XCV_TYPE             RMII
#define CONFIG_ETHPRIME                 "FEC"
#define CONFIG_FEC_MXC_PHYADDR          0

#define CONFIG_PHYLIB
#define CONFIG_PHY_MICREL
#define CONFIG_IP_DEFRAG
#define CONFIG_TFTP_BLOCKSIZE		16352
#define CONFIG_TFTP_TSIZE

/* ENET1 */
#define IMX_FEC_BASE			ENET_IPS_BASE_ADDR

/* MMC Config*/
#define CONFIG_SYS_FSL_ESDHC_ADDR	0
#define CONFIG_SYS_FSL_USDHC_NUM	1

#undef CONFIG_BOOTM_PLAN9
#undef CONFIG_BOOTM_RTEMS

/* I2C configs */
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_SPEED		100000

#define CONFIG_IPADDR			192.168.10.2
#define CONFIG_NETMASK			255.255.255.0
#define CONFIG_SERVERIP			192.168.10.1

#define MEM_LAYOUT_ENV_SETTINGS \
	"fdt_addr_r=0x82000000\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"kernel_addr_r=0x81000000\0" \
	"ramdisk_addr_r=0x82100000\0"

#define SD_BOOTCMD \
	"sdargs=root=/dev/mmcblk0p2 rw rootwait\0"	\
	"sdboot=run setup; setenv bootargs ${defargs} ${sdargs} " \
	"${setupargs} ${vidargs}; echo Booting from MMC/SD card...; " \
	"run m4boot && " \
	"load mmc 0:1 ${kernel_addr_r} ${kernel_file} && " \
	"load mmc 0:1 ${fdt_addr_r} ${soc}-colibri-${fdt_board}.dtb && " \
	"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \

#define NFS_BOOTCMD \
	"nfsargs=ip=:::::eth0: root=/dev/nfs\0"	\
	"nfsboot=run setup; " \
		"setenv bootargs ${defargs} ${nfsargs} " \
		"${setupargs} ${vidargs}; echo Booting from NFS...;" \
		"dhcp ${kernel_addr_r} && "	\
		"tftp ${fdt_addr_r} ${soc}-colibri-${fdt_board}.dtb && " \
		"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \

#define UBI_BOOTCMD	\
	"ubiargs=ubi.mtd=ubi root=ubi0:rootfs rootfstype=ubifs " \
		"ubi.fm_autoconvert=1\0" \
	"ubiboot=run setup; " \
		"setenv bootargs ${defargs} ${ubiargs} " \
		"${setupargs} ${vidargs}; echo Booting from NAND...; " \
		"ubi part ubi && run m4boot && " \
		"ubi read ${kernel_addr_r} kernel && " \
		"ubi read ${fdt_addr_r} dtb && " \
		"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \

#define CONFIG_BOOTCOMMAND "run ubiboot; run sdboot; run nfsboot"

#define CONFIG_EXTRA_ENV_SETTINGS \
	MEM_LAYOUT_ENV_SETTINGS \
	NFS_BOOTCMD \
	SD_BOOTCMD \
	UBI_BOOTCMD \
	"console=ttymxc0\0" \
	"defargs=\0" \
	"fdt_board=eval-v3\0" \
	"fdt_fixup=;\0" \
	"m4boot=;\0" \
	"ip_dyn=yes\0" \
	"kernel_file=zImage\0" \
	"mtdparts=" MTDPARTS_DEFAULT "\0" \
	"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
		"00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \
		"${board}/flash_eth.img && source ${loadaddr}\0" \
	"setsdupdate=mmc rescan && setenv interface mmc && " \
		"fatload ${interface} 0:1 ${loadaddr} " \
		"${board}/flash_blk.img && source ${loadaddr}\0" \
	"setup=setenv setupargs " \
		"console=tty1 console=${console}" \
		",${baudrate}n8 ${memargs} consoleblank=0 ${mtdparts}\0" \
	"setupdate=run setsdupdate || run setusbupdate || run setethupdate\0" \
	"setusbupdate=usb start && setenv interface usb && " \
		"fatload ${interface} 0:1 ${loadaddr} " \
		"${board}/flash_blk.img && source ${loadaddr}\0" \
	"splashpos=m,m\0" \
	"videomode=video=ctfb:x:640,y:480,depth:18,pclk:39722,le:48,ri:16,up:33,lo:10,hs:96,vs:2,sync:0,vmode:0\0" \

/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP

#define CONFIG_SYS_MEMTEST_START	0x80000000
#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x0c000000)

#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
#define CONFIG_SYS_HZ			1000

#define CONFIG_STACKSIZE		SZ_128K

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS		1
#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/* FLASH and environment organization */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_IS_IN_NAND

#if defined(CONFIG_ENV_IS_IN_MMC)
#define CONFIG_SYS_MMC_ENV_DEV		0   /* USDHC1 */
#define CONFIG_SYS_MMC_ENV_PART		0	/* user area */
#define CONFIG_MMCROOT			"/dev/mmcblk0p2"  /* USDHC1 */
#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
#elif defined(CONFIG_ENV_IS_IN_NAND)
#define CONFIG_ENV_OFFSET		(4 * 1024 * 1024)
#define CONFIG_ENV_SECT_SIZE		(128 * 1024)
#define CONFIG_ENV_SIZE			CONFIG_ENV_SECT_SIZE
#endif

#define CONFIG_NAND_MXS
#define CONFIG_CMD_NAND_TRIMFFS

/* NAND stuff */
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		0x40000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_MX7_GPMI_62_ECC_BYTES
#define CONFIG_CMD_NAND_TORTURE

/* UBI stuff */
#define CONFIG_RBTREE
#define CONFIG_LZO
#define CONFIG_CMD_UBIFS	/* increases size by almost 60 KB */

/* Dynamic MTD partition support */
#define CONFIG_CMD_MTDPARTS	/* Enable 'mtdparts' command line support */
#define CONFIG_MTD_PARTITIONS
#define CONFIG_MTD_DEVICE	/* needed for mtdparts commands */
#define MTDIDS_DEFAULT		"nand0=gpmi-nand"
#define MTDPARTS_DEFAULT	"mtdparts=gpmi-nand:"		\
				"512k(mx7-bcb),"		\
				"3584k(u-boot)ro,"		\
				"512k(u-boot-env),"		\
				"-(ubi)"

/* DMA stuff, needed for GPMI/MXS NAND support */
#define CONFIG_APBH_DMA
#define CONFIG_APBH_DMA_BURST
#define CONFIG_APBH_DMA_BURST8

/* USB Configs */
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET

#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS		0
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2

#define CONFIG_IMX_THERMAL

#define CONFIG_USBD_HS

#define CONFIG_USB_FUNCTION_MASS_STORAGE

/* USB Device Firmware Update support */
#define CONFIG_SYS_DFU_DATA_BUF_SIZE	SZ_16M
#define DFU_DEFAULT_POLL_TIMEOUT	300

#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_MXS
#define CONFIG_VIDEO_LOGO
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_BMP_LOGO
#endif

#endif