/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2018 NXP
 */

#ifndef __IMX8M_EVK_H
#define __IMX8M_EVK_H

#include <linux/sizes.h>
#include <linux/stringify.h>
#include <asm/arch/imx-regs.h>

#define CONFIG_SYS_BOOTM_LEN		(32 * SZ_1M)

#define CONFIG_SPL_MAX_SIZE		(124 * 1024)
#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300

#ifdef CONFIG_SPL_BUILD
/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
#define CONFIG_SPL_WATCHDOG
#define CONFIG_SPL_DRIVERS_MISC
#define CONFIG_SPL_POWER
#define CONFIG_SPL_I2C
#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_STACK		0x187FF0
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_GPIO
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_BSS_START_ADDR      0x00180000
#define CONFIG_SPL_BSS_MAX_SIZE        0x2000	/* 8 KB */
#define CONFIG_SYS_SPL_MALLOC_START    0x42200000
#define CONFIG_SYS_SPL_MALLOC_SIZE    0x80000	/* 512 KB */
#define CONFIG_SYS_SPL_PTE_RAM_BASE    0x41580000

/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
#define CONFIG_MALLOC_F_ADDR		0x182000
/* For RAW image gives a error info not panic */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE

#undef CONFIG_DM_MMC
#undef CONFIG_DM_PMIC
#undef CONFIG_DM_PMIC_PFUZE100

#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
#endif

#define CONFIG_REMAKE_ELF

/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
#define CONFIG_MII
#define CONFIG_ETHPRIME                 "FEC"

#define CONFIG_FEC_MXC
#define CONFIG_FEC_XCV_TYPE             RGMII
#define CONFIG_FEC_MXC_PHYADDR          0
#define FEC_QUIRK_ENET_MAC

#define CONFIG_PHY_GIGE
#define IMX_FEC_BASE			0x30BE0000
#endif

#ifndef CONFIG_SPL_BUILD
#define BOOT_TARGET_DEVICES(func) \
       func(MMC, mmc, 0) \
       func(MMC, mmc, 1) \
       func(DHCP, dhcp, na)

#include <config_distro_bootcmd.h>
#endif

/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS		\
	BOOTENV \
	"scriptaddr=0x43500000\0" \
	"kernel_addr_r=0x40880000\0" \
	"image=Image\0" \
	"console=ttymxc0,115200\0" \
	"fdt_addr=0x43000000\0"			\
	"boot_fdt=try\0" \
	"fdt_file=imx8mq-evk.dtb\0" \
	"initrd_addr=0x43800000\0"		\
	"bootm_size=0x10000000\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \

/* Link Definitions */

#define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE        0x80000
#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)

#define CONFIG_SYS_SDRAM_BASE           0x40000000
#define PHYS_SDRAM                      0x40000000
#define PHYS_SDRAM_SIZE			0xC0000000 /* 3GB DDR */

#define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR

/* Monitor Command Prompt */
#undef CONFIG_SYS_PROMPT
#define CONFIG_SYS_PROMPT		"u-boot=> "
#define CONFIG_SYS_CBSIZE		1024
#define CONFIG_SYS_MAXARGS		64
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)

#define CONFIG_IMX_BOOTAUX

#define CONFIG_SYS_FSL_USDHC_NUM	2
#define CONFIG_SYS_FSL_ESDHC_ADDR       0

#define CONFIG_SYS_MMC_IMG_LOAD_PART	1

#define CONFIG_MXC_GPIO

#define CONFIG_OF_SYSTEM_SETUP

#ifndef CONFIG_SPL_BUILD
#define CONFIG_DM_PMIC
#endif

#endif