/*
 * (C) Copyright 2001
 * Frank Gottschling, ELTEC Elektronik AG, fgottschling@eltec.de
 *
 * (C) Copyright 2001
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * Configuation settings for the miniHiPerCam.
 *
 * -----------------------------------------------------------------
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */
#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
#define CONFIG_MHPC 		1	/* on a miniHiPerCam	        */
#define CONFIG_BOARD_PRE_INIT   1       /* do special hardware init.    */
#define CONFIG_MISC_INIT_R      1

#define CONFIG_8xx_GCLK_FREQ	MPC8XX_SPEED
#undef	CONFIG_8xx_CONS_SMC1
#define	CONFIG_8xx_CONS_SMC2	1	/* Console is on SMC2		*/
#undef	CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE		9600
#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/

#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */

#define CONFIG_ENV_OVERWRITE    1
#define CONFIG_ETHADDR          00:00:5b:ee:de:ad

#undef  CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND	\
	"bootp;"								\
	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
	"bootm"

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/

#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/

#undef  CONFIG_UCODE_PATCH

/* enable I2C and select the hardware/software driver */
#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
/*
 * Software (bit-bang) I2C driver configuration
 */
#define PB_SCL		0x00000020	/* PB 26 */
#define PB_SDA		0x00000010	/* PB 27 */

#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */

#define CFG_I2C_SPEED                   50000
#define CFG_I2C_SLAVE                   0xFE
#define CFG_I2C_EEPROM_ADDR             0x50    /* EEPROM X24C04		*/
#define CFG_I2C_EEPROM_ADDR_LEN         1       /* bytes of address		*/
/* mask of address bits that overflow into the "EEPROM chip address"    */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW    0x07
#define CFG_EEPROM_PAGE_WRITE_BITS      3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS  10

#define LCD_VIDEO_ADDR          (SDRAM_MAX_SIZE-SDRAM_RES_SIZE)
#define LCD_VIDEO_SIZE          SDRAM_RES_SIZE  /* 2MB */
#define LCD_VIDEO_COLS          640
#define LCD_VIDEO_ROWS          480
#define LCD_VIDEO_FG            255
#define LCD_VIDEO_BG            0

#undef  CONFIG_VIDEO                            /* test only ! s.a devices.c and 8xx */
#define CONFIG_CFB_CONSOLE                      /* framebuffer console with std input */
#define CONFIG_VIDEO_LOGO

#define VIDEO_KBD_INIT_FCT      0               /* no KBD dev on MHPC - use serial */
#define VIDEO_TSTC_FCT          serial_tstc
#define VIDEO_GETC_FCT          serial_getc

#define CONFIG_BR0_WORKAROUND   1

#define CONFIG_COMMANDS	     ( CONFIG_CMD_DFL  | \
			       CFG_CMD_DATE    | \
			       CFG_CMD_EEPROM  | \
			       CFG_CMD_ELF     | \
			       CFG_CMD_I2C     | \
			       CFG_CMD_JFFS2   | \
			       CFG_CMD_REGINFO )

#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)

/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>

/*
 * Miscellaneous configurable options
 */
#define	CFG_LONGHELP			/* undef to save memory		*/
#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define	CFG_MAXARGS	16		/* max number of command args	*/
#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/

#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

#define	CFG_LOAD_ADDR		0x300000	/* default load address	*/

#define	CFG_HZ                  1000		/* decrementer freq: 1 ms ticks	*/

#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */

/*-----------------------------------------------------------------------
 * Physical memory map
 */
#define CFG_IMMR		0xFFF00000 /* Internal Memory Mapped Register*/

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in DPRAM)
 */
#define CFG_INIT_RAM_ADDR	CFG_IMMR
#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
#define	CFG_GBL_DATA_SIZE       64  /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET     (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CFG_SDRAM_BASE _must_ start at 0
 */
#define	CFG_SDRAM_BASE		0x00000000
#define CFG_FLASH_BASE		0xfe000000

#define	CFG_MONITOR_LEN		0x40000 	/* Reserve 256 kB for Monitor	*/
#undef  CFG_MONITOR_BASE	            /* to run U-Boot from RAM */
#define CFG_MONITOR_BASE	CFG_FLASH_BASE
#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/

#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
#define CFG_JFFS2_NUM_BANKS     1           /* one flash only */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map- for Linux	*/

/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#define CFG_MAX_FLASH_SECT	64	/* max number of sectors on one chip	*/

#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
#define	CFG_ENV_IS_IN_FLASH	1
#define CFG_ENV_OFFSET		CFG_MONITOR_LEN	/* Offset of Environment */
#define	CFG_ENV_SIZE		0x20000	/* Total Size of Environment 	*/

/*-----------------------------------------------------------------------
 * Cache Configuration
 */
#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
#endif

/*-----------------------------------------------------------------------
 * SYPCR - System Protection Control				11-9
 * SYPCR can only be written once after reset!
 *-----------------------------------------------------------------------
 * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 */
#if defined(CONFIG_WATCHDOG)
#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
#else
#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
			 SYPCR_SWP)
#endif

/*-----------------------------------------------------------------------
 * SIUMCR - SIU Module Configuration				11-6
 *-----------------------------------------------------------------------
 * PCMCIA config., multi-function pin tri-state
 */
#define CFG_SIUMCR	(SIUMCR_SEME)

/*-----------------------------------------------------------------------
 * TBSCR - Time Base Status and Control				11-26
 *-----------------------------------------------------------------------
 * Clear Reference Interrupt Status, Timebase freezing enabled
 */
#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)

/*-----------------------------------------------------------------------
 * PISCR - Periodic Interrupt Status and Control		11-31
 *-----------------------------------------------------------------------
 * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 */
#define CFG_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)

/*-----------------------------------------------------------------------
 * RTCSC - Real-Time Clock Status and Control Register		12-18
 *-----------------------------------------------------------------------
 */
#define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)

/*-----------------------------------------------------------------------
 * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
 *-----------------------------------------------------------------------
 * Reset PLL lock status sticky bit, timer expired status bit and timer
 * interrupt status bit - leave PLL multiplication factor unchanged !
 */
#define MPC8XX_SPEED	50000000L
#define MPC8XX_XIN   	5000000L      /* ref clk */
#define MPC8XX_FACT	(MPC8XX_SPEED/MPC8XX_XIN)
#define CFG_PLPRCR	(((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
			PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)

/*-----------------------------------------------------------------------
 * SCCR - System Clock and reset Control Register		15-27
 *-----------------------------------------------------------------------
 * Set clock output, timebase and RTC source and divider,
 * power management and some other internal clocks
 */

#define SCCR_MASK	(SCCR_RTDIV | SCCR_RTSEL)     /* SCCR_EBDF11 */
#define CFG_SCCR	(SCCR_TBS | SCCR_DFLCD001)


/*-----------------------------------------------------------------------
 * MAMR settings for SDRAM	- 16-14
 * => 0xC080200F
 *-----------------------------------------------------------------------
 * periodic timer for refresh
 */
#define CFG_MAMR_PTA	0xC0
#define CFG_MAMR	((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | MAMR_G0CLA_A11 | MAMR_TLFA_MSK)

/*
 * BR0 and OR0 (FLASH) used to re-map FLASH
 */

/* allow for max 8 MB of Flash */
#define FLASH_BASE		0xFE000000	/* FLASH bank #0*/
#define FLASH_BASE0_PRELIM	0xFE000000	/* FLASH bank #0*/
#define CFG_REMAP_OR_AM		0xFF800000	/* OR addr mask */
#define CFG_PRELIM_OR_AM	0xFF800000	/* OR addr mask */

#define CFG_OR_TIMING_FLASH	(OR_CSNT_SAM | OR_BI | OR_SCY_8_CLK) /* (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK)*/

#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_BR0_PRELIM	((FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_MS_GPCM | BR_V )

/*
 * BR1 and OR1 (SDRAM)
 */
#define SDRAM_BASE1_PRELIM	0x00000000	/* SDRAM bank #0	*/
#define SDRAM_MAX_SIZE		0x01000000	/* max 16 MB    	*/
#define SDRAM_RES_SIZE          0x00200000      /* 2 MB for framebuffer */

/* SDRAM timing: drive GPL5 high on first cycle */
#define CFG_OR_TIMING_SDRAM	(OR_G5LS)

#define CFG_OR1_PRELIM	((~(SDRAM_MAX_SIZE)+1)| CFG_OR_TIMING_SDRAM )
#define CFG_BR1_PRELIM	((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )

/*
 * BR2/OR2 - DIMM
 */
#define CFG_OR2		(OR_ACS_DIV4)
#define CFG_BR2		(BR_MS_UPMA)

/*
 * BR3/OR3 - DIMM
 */
#define CFG_OR3		(OR_ACS_DIV4)
#define CFG_BR3		(BR_MS_UPMA)

/*
 * BR4/OR4
 */
#define CFG_OR4		0
#define CFG_BR4		0

/*
 * BR5/OR5
 */
#define CFG_OR5		0
#define CFG_BR5		0

/*
 * BR6/OR6
 */
#define CFG_OR6		0
#define CFG_BR6		0

/*
 * BR7/OR7
 */
#define CFG_OR7		0
#define CFG_BR7		0


/*-----------------------------------------------------------------------
 * Debug Entry Mode
 *-----------------------------------------------------------------------
 *
 */
#define CFG_DER	0

/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
#define BOOTFLAG_WARM	0x02		/* Software reboot			*/

#endif	/* __CONFIG_H */