/*
 * Copyright (C) 2013 Freescale Semiconductor, Inc.
 *
 * Configuration settings for the Wandboard.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include <config_distro_defaults.h>
#include "mx6_common.h"

#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#include "imx6_spl.h"

#define MACH_TYPE_WANDBOARD		4412
#define CONFIG_MACH_TYPE		MACH_TYPE_WANDBOARD

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT

#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE		UART1_BASE

/* Command definition */
#define CONFIG_CMD_BMODE

#define CONFIG_SYS_MEMTEST_START	0x10000000
#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)

/* I2C Configs */
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED		100000

/* MMC Configuration */
#define CONFIG_SYS_FSL_USDHC_NUM	2
#define CONFIG_SYS_FSL_ESDHC_ADDR	0

/* USB Configs */
#define CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS		0

/* Ethernet Configuration */
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE			ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE		RGMII
#define CONFIG_ETHPRIME			"FEC"
#define CONFIG_FEC_MXC_PHYADDR		1
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS

/* Framebuffer */
#define CONFIG_VIDEO
#define CONFIG_VIDEO_IPUV3
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IPUV3_CLK 260000000
#define CONFIG_CMD_HDMIDETECT
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP

#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
#define CONFIG_EXTRA_ENV_SETTINGS \
	"console=ttymxc0,115200\0" \
	"splashpos=m,m\0" \
	"fdtfile=undefined\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_addr_r=0x18000000\0" \
	"fdt_addr=0x18000000\0" \
	"ip_dyn=yes\0" \
	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
	"update_sd_firmware_filename=u-boot.imx\0" \
	"update_sd_firmware=" \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"if mmc dev ${mmcdev}; then "	\
			"if ${get_cmd} ${update_sd_firmware_filename}; then " \
				"setexpr fw_sz ${filesize} / 0x200; " \
				"setexpr fw_sz ${fw_sz} + 1; "	\
				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
			"fi; "	\
		"fi\0" \
	"videoargs=" \
		"setenv nextcon 0; " \
		"if hdmidet; then " \
			"setenv bootargs ${bootargs} " \
				"video=mxcfb${nextcon}:dev=hdmi,1280x720M@60," \
					"if=RGB24; " \
			"setenv fbmen fbmem=28M; " \
			"setexpr nextcon ${nextcon} + 1; " \
		"else " \
			"echo - no HDMI monitor;" \
		"fi; " \
		"i2c dev 1; " \
		"if i2c probe 0x10; then " \
			"setenv bootargs ${bootargs} " \
				"video=mxcfb${nextcon}:dev=lcd,800x480@60," \
					"if=RGB666,bpp=32; " \
			"if test 0 -eq ${nextcon}; then " \
				"setenv fbmem fbmem=10M; " \
			"else " \
				"setenv fbmem ${fbmem},10M; " \
			"fi; " \
			"setexpr nextcon ${nextcon} + 1; " \
		"else " \
			"echo '- no FWBADAPT-7WVGA-LCD-F07A-0102 display';" \
		"fi; " \
		"setenv bootargs ${bootargs} ${fbmem}\0" \
	"findfdt="\
		"if test $board_name = C1 && test $board_rev = MX6Q ; then " \
			"setenv fdtfile imx6q-wandboard.dtb; fi; " \
		"if test $board_name = C1 && test $board_rev = MX6DL ; then " \
			"setenv fdtfile imx6dl-wandboard.dtb; fi; " \
		"if test $board_name = B1 && test $board_rev = MX6Q ; then " \
			"setenv fdtfile imx6q-wandboard-revb1.dtb; fi; " \
		"if test $board_name = B1 && test $board_rev = MX6DL ; then " \
			"setenv fdtfile imx6dl-wandboard-revb1.dtb; fi; " \
		"if test $fdtfile = undefined; then " \
			"echo WARNING: Could not determine dtb to use; fi; \0" \
	"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
	"pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
	"ramdisk_addr_r=0x13000000\0" \
	"ramdiskaddr=0x13000000\0" \
	"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
	BOOTENV

#define BOOT_TARGET_DEVICES(func) \
	func(MMC, mmc, 0) \
	func(MMC, mmc, 1) \
	func(USB, usb, 0) \
	func(PXE, pxe, na) \
	func(DHCP, dhcp, na)

#define CONFIG_BOOTCOMMAND \
	   "run findfdt; " \
	   "run distro_bootcmd"

#include <config_distro_bootcmd.h>

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS		1
#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/* Environment organization */
#define CONFIG_ENV_SIZE			(8 * 1024)

#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_ENV_OFFSET		(6 * 64 * 1024)
#define CONFIG_SYS_MMC_ENV_DEV		0

#endif			       /* __CONFIG_H * */