// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2022, Linaro Limited
 */

#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/clock/qcom,sm8450-videocc.h>
#include <dt-bindings/clock/qcom,sm8550-camcc.h>
#include <dt-bindings/clock/qcom,sm8550-gcc.h>
#include <dt-bindings/clock/qcom,sm8550-gpucc.h>
#include <dt-bindings/clock/qcom,sm8550-tcsr.h>
#include <dt-bindings/clock/qcom,sm8550-dispcc.h>
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/firmware/qcom,scm.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interconnect/qcom,sm8550-rpmh.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/power/qcom,rpmhpd.h>
#include <dt-bindings/soc/qcom,gpr.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
#include <dt-bindings/phy/phy-qcom-qmp.h>
#include <dt-bindings/thermal/thermal.h>

/ {
	interrupt-parent = <&intc>;

	#address-cells = <2>;
	#size-cells = <2>;

	chosen { };

	clocks {
		xo_board: xo-board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
		};

		sleep_clk: sleep-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
		};

		bi_tcxo_div2: bi-tcxo-div2-clk {
			#clock-cells = <0>;
			compatible = "fixed-factor-clock";
			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-mult = <1>;
			clock-div = <2>;
		};

		bi_tcxo_ao_div2: bi-tcxo-ao-div2-clk {
			#clock-cells = <0>;
			compatible = "fixed-factor-clock";
			clocks = <&rpmhcc RPMH_CXO_CLK_A>;
			clock-mult = <1>;
			clock-div = <2>;
		};

		pcie_1_phy_aux_clk: pcie-1-phy-aux-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
		};
	};

	cpus {
		#address-cells = <2>;
		#size-cells = <0>;

		CPU0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-a510";
			reg = <0 0>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			next-level-cache = <&L2_0>;
			power-domains = <&CPU_PD0>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <100>;
			#cooling-cells = <2>;
			L2_0: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
				L3_0: l3-cache {
					compatible = "cache";
					cache-level = <3>;
					cache-unified;
				};
			};
		};

		CPU1: cpu@100 {
			device_type = "cpu";
			compatible = "arm,cortex-a510";
			reg = <0 0x100>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			next-level-cache = <&L2_100>;
			power-domains = <&CPU_PD1>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <100>;
			#cooling-cells = <2>;
			L2_100: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU2: cpu@200 {
			device_type = "cpu";
			compatible = "arm,cortex-a510";
			reg = <0 0x200>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			next-level-cache = <&L2_200>;
			power-domains = <&CPU_PD2>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <100>;
			#cooling-cells = <2>;
			L2_200: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU3: cpu@300 {
			device_type = "cpu";
			compatible = "arm,cortex-a715";
			reg = <0 0x300>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			next-level-cache = <&L2_300>;
			power-domains = <&CPU_PD3>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			capacity-dmips-mhz = <1792>;
			dynamic-power-coefficient = <270>;
			#cooling-cells = <2>;
			L2_300: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU4: cpu@400 {
			device_type = "cpu";
			compatible = "arm,cortex-a715";
			reg = <0 0x400>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			next-level-cache = <&L2_400>;
			power-domains = <&CPU_PD4>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			capacity-dmips-mhz = <1792>;
			dynamic-power-coefficient = <270>;
			#cooling-cells = <2>;
			L2_400: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU5: cpu@500 {
			device_type = "cpu";
			compatible = "arm,cortex-a710";
			reg = <0 0x500>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			next-level-cache = <&L2_500>;
			power-domains = <&CPU_PD5>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			capacity-dmips-mhz = <1792>;
			dynamic-power-coefficient = <270>;
			#cooling-cells = <2>;
			L2_500: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU6: cpu@600 {
			device_type = "cpu";
			compatible = "arm,cortex-a710";
			reg = <0 0x600>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			next-level-cache = <&L2_600>;
			power-domains = <&CPU_PD6>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			capacity-dmips-mhz = <1792>;
			dynamic-power-coefficient = <270>;
			#cooling-cells = <2>;
			L2_600: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU7: cpu@700 {
			device_type = "cpu";
			compatible = "arm,cortex-x3";
			reg = <0 0x700>;
			clocks = <&cpufreq_hw 2>;
			enable-method = "psci";
			next-level-cache = <&L2_700>;
			power-domains = <&CPU_PD7>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 2>;
			capacity-dmips-mhz = <1894>;
			dynamic-power-coefficient = <588>;
			#cooling-cells = <2>;
			L2_700: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		cpu-map {
			cluster0 {
				core0 {
					cpu = <&CPU0>;
				};

				core1 {
					cpu = <&CPU1>;
				};

				core2 {
					cpu = <&CPU2>;
				};

				core3 {
					cpu = <&CPU3>;
				};

				core4 {
					cpu = <&CPU4>;
				};

				core5 {
					cpu = <&CPU5>;
				};

				core6 {
					cpu = <&CPU6>;
				};

				core7 {
					cpu = <&CPU7>;
				};
			};
		};

		idle-states {
			entry-method = "psci";

			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
				compatible = "arm,idle-state";
				idle-state-name = "silver-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <550>;
				exit-latency-us = <750>;
				min-residency-us = <6700>;
				local-timer-stop;
			};

			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
				compatible = "arm,idle-state";
				idle-state-name = "gold-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <600>;
				exit-latency-us = <1300>;
				min-residency-us = <8136>;
				local-timer-stop;
			};

			PRIME_CPU_SLEEP_0: cpu-sleep-2-0 {
				compatible = "arm,idle-state";
				idle-state-name = "goldplus-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <500>;
				exit-latency-us = <1350>;
				min-residency-us = <7480>;
				local-timer-stop;
			};
		};

		domain-idle-states {
			CLUSTER_SLEEP_0: cluster-sleep-0 {
				compatible = "domain-idle-state";
				arm,psci-suspend-param = <0x41000044>;
				entry-latency-us = <750>;
				exit-latency-us = <2350>;
				min-residency-us = <9144>;
			};

			CLUSTER_SLEEP_1: cluster-sleep-1 {
				compatible = "domain-idle-state";
				arm,psci-suspend-param = <0x4100c344>;
				entry-latency-us = <2800>;
				exit-latency-us = <4400>;
				min-residency-us = <10150>;
			};
		};
	};

	firmware {
		scm: scm {
			compatible = "qcom,scm-sm8550", "qcom,scm";
			qcom,dload-mode = <&tcsr 0x19000>;
			interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
		};
	};

	clk_virt: interconnect-0 {
		compatible = "qcom,sm8550-clk-virt";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	mc_virt: interconnect-1 {
		compatible = "qcom,sm8550-mc-virt";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	memory@a0000000 {
		device_type = "memory";
		/* We expect the bootloader to fill in the size */
		reg = <0 0xa0000000 0 0>;
	};

	pmu {
		compatible = "arm,armv8-pmuv3";
		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
	};

	psci {
		compatible = "arm,psci-1.0";
		method = "smc";

		CPU_PD0: power-domain-cpu0 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD1: power-domain-cpu1 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD2: power-domain-cpu2 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD3: power-domain-cpu3 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD4: power-domain-cpu4 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD5: power-domain-cpu5 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD6: power-domain-cpu6 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD7: power-domain-cpu7 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&PRIME_CPU_SLEEP_0>;
		};

		CLUSTER_PD: power-domain-cluster {
			#power-domain-cells = <0>;
			domain-idle-states = <&CLUSTER_SLEEP_0>, <&CLUSTER_SLEEP_1>;
		};
	};

	reserved_memory: reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		hyp_mem: hyp-region@80000000 {
			reg = <0 0x80000000 0 0xa00000>;
			no-map;
		};

		cpusys_vm_mem: cpusys-vm-region@80a00000 {
			reg = <0 0x80a00000 0 0x400000>;
			no-map;
		};

		hyp_tags_mem: hyp-tags-region@80e00000 {
			reg = <0 0x80e00000 0 0x3d0000>;
			no-map;
		};

		xbl_sc_mem: xbl-sc-region@d8100000 {
			reg = <0 0xd8100000 0 0x40000>;
			no-map;
		};

		hyp_tags_reserved_mem: hyp-tags-reserved-region@811d0000 {
			reg = <0 0x811d0000 0 0x30000>;
			no-map;
		};

		/* merged xbl_dt_log, xbl_ramdump, aop_image */
		xbl_dt_log_merged_mem: xbl-dt-log-merged-region@81a00000 {
			reg = <0 0x81a00000 0 0x260000>;
			no-map;
		};

		aop_cmd_db_mem: aop-cmd-db-region@81c60000 {
			compatible = "qcom,cmd-db";
			reg = <0 0x81c60000 0 0x20000>;
			no-map;
		};

		/* merged aop_config, tme_crash_dump, tme_log, uefi_log */
		aop_config_merged_mem: aop-config-merged-region@81c80000 {
			reg = <0 0x81c80000 0 0x74000>;
			no-map;
		};

		/* secdata region can be reused by apps */
		smem: smem@81d00000 {
			compatible = "qcom,smem";
			reg = <0 0x81d00000 0 0x200000>;
			hwlocks = <&tcsr_mutex 3>;
			no-map;
		};

		adsp_mhi_mem: adsp-mhi-region@81f00000 {
			reg = <0 0x81f00000 0 0x20000>;
			no-map;
		};

		global_sync_mem: global-sync-region@82600000 {
			reg = <0 0x82600000 0 0x100000>;
			no-map;
		};

		tz_stat_mem: tz-stat-region@82700000 {
			reg = <0 0x82700000 0 0x100000>;
			no-map;
		};

		cdsp_secure_heap_mem: cdsp-secure-heap-region@82800000 {
			reg = <0 0x82800000 0 0x4600000>;
			no-map;
		};

		mpss_mem: mpss-region@8a800000 {
			reg = <0 0x8a800000 0 0x10800000>;
			no-map;
		};

		q6_mpss_dtb_mem: q6-mpss-dtb-region@9b000000 {
			reg = <0 0x9b000000 0 0x80000>;
			no-map;
		};

		ipa_fw_mem: ipa-fw-region@9b080000 {
			reg = <0 0x9b080000 0 0x10000>;
			no-map;
		};

		ipa_gsi_mem: ipa-gsi-region@9b090000 {
			reg = <0 0x9b090000 0 0xa000>;
			no-map;
		};

		gpu_micro_code_mem: gpu-micro-code-region@9b09a000 {
			reg = <0 0x9b09a000 0 0x2000>;
			no-map;
		};

		spss_region_mem: spss-region@9b100000 {
			reg = <0 0x9b100000 0 0x180000>;
			no-map;
		};

		/* First part of the "SPU secure shared memory" region */
		spu_tz_shared_mem: spu-tz-shared-region@9b280000 {
			reg = <0 0x9b280000 0 0x60000>;
			no-map;
		};

		/* Second part of the "SPU secure shared memory" region */
		spu_modem_shared_mem: spu-modem-shared-region@9b2e0000 {
			reg = <0 0x9b2e0000 0 0x20000>;
			no-map;
		};

		camera_mem: camera-region@9b300000 {
			reg = <0 0x9b300000 0 0x800000>;
			no-map;
		};

		video_mem: video-region@9bb00000 {
			reg = <0 0x9bb00000 0 0x700000>;
			no-map;
		};

		cvp_mem: cvp-region@9c200000 {
			reg = <0 0x9c200000 0 0x700000>;
			no-map;
		};

		cdsp_mem: cdsp-region@9c900000 {
			reg = <0 0x9c900000 0 0x2000000>;
			no-map;
		};

		q6_cdsp_dtb_mem: q6-cdsp-dtb-region@9e900000 {
			reg = <0 0x9e900000 0 0x80000>;
			no-map;
		};

		q6_adsp_dtb_mem: q6-adsp-dtb-region@9e980000 {
			reg = <0 0x9e980000 0 0x80000>;
			no-map;
		};

		adspslpi_mem: adspslpi-region@9ea00000 {
			reg = <0 0x9ea00000 0 0x4080000>;
			no-map;
		};

		/* uefi region can be reused by apps */

		/* Linux kernel image is loaded at 0xa8000000 */

		rmtfs_mem: rmtfs-region@d4a80000 {
			compatible = "qcom,rmtfs-mem";
			reg = <0x0 0xd4a80000 0x0 0x280000>;
			no-map;

			qcom,client-id = <1>;
			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
		};

		mpss_dsm_mem: mpss-dsm-region@d4d00000 {
			reg = <0 0xd4d00000 0 0x3300000>;
			no-map;
		};

		tz_reserved_mem: tz-reserved-region@d8000000 {
			reg = <0 0xd8000000 0 0x100000>;
			no-map;
		};

		cpucp_fw_mem: cpucp-fw-region@d8140000 {
			reg = <0 0xd8140000 0 0x1c0000>;
			no-map;
		};

		qtee_mem: qtee-region@d8300000 {
			reg = <0 0xd8300000 0 0x500000>;
			no-map;
		};

		ta_mem: ta-region@d8800000 {
			reg = <0 0xd8800000 0 0x8a00000>;
			no-map;
		};

		tz_tags_mem: tz-tags-region@e1200000 {
			reg = <0 0xe1200000 0 0x2740000>;
			no-map;
		};

		hwfence_shbuf: hwfence-shbuf-region@e6440000 {
			reg = <0 0xe6440000 0 0x279000>;
			no-map;
		};

		trust_ui_vm_mem: trust-ui-vm-region@f3600000 {
			reg = <0 0xf3600000 0 0x4aee000>;
			no-map;
		};

		trust_ui_vm_dump: trust-ui-vm-dump-region@f80ee000 {
			reg = <0 0xf80ee000 0 0x1000>;
			no-map;
		};

		trust_ui_vm_qrtr: trust-ui-vm-qrt-region@f80ef000 {
			reg = <0 0xf80ef000 0 0x9000>;
			no-map;
		};

		trust_ui_vm_vblk0_ring: trust-ui-vm-vblk0-ring-region@f80f8000 {
			reg = <0 0xf80f8000 0 0x4000>;
			no-map;
		};

		trust_ui_vm_vblk1_ring: trust-ui-vm-vblk1-ring-region@f80fc000 {
			reg = <0 0xf80fc000 0 0x4000>;
			no-map;
		};

		trust_ui_vm_swiotlb: trust-ui-vm-swiotlb-region@f8100000 {
			reg = <0 0xf8100000 0 0x100000>;
			no-map;
		};

		oem_vm_mem: oem-vm-region@f8400000 {
			reg = <0 0xf8400000 0 0x4800000>;
			no-map;
		};

		oem_vm_vblk0_ring: oem-vm-vblk0-ring-region@fcc00000 {
			reg = <0 0xfcc00000 0 0x4000>;
			no-map;
		};

		oem_vm_swiotlb: oem-vm-swiotlb-region@fcc04000 {
			reg = <0 0xfcc04000 0 0x100000>;
			no-map;
		};

		hyp_ext_tags_mem: hyp-ext-tags-region@fce00000 {
			reg = <0 0xfce00000 0 0x2900000>;
			no-map;
		};

		hyp_ext_reserved_mem: hyp-ext-reserved-region@ff700000 {
			reg = <0 0xff700000 0 0x100000>;
			no-map;
		};
	};

	smp2p-adsp {
		compatible = "qcom,smp2p";
		qcom,smem = <443>, <429>;
		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_LPASS
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <2>;

		smp2p_adsp_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_adsp_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-cdsp {
		compatible = "qcom,smp2p";
		qcom,smem = <94>, <432>;
		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_CDSP
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <5>;

		smp2p_cdsp_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_cdsp_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-modem {
		compatible = "qcom,smp2p";
		qcom,smem = <435>, <428>;
		interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_MPSS
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <1>;

		smp2p_modem_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_modem_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};

		ipa_smp2p_out: ipa-ap-to-modem {
			qcom,entry-name = "ipa";
			#qcom,smem-state-cells = <1>;
		};

		ipa_smp2p_in: ipa-modem-to-ap {
			qcom,entry-name = "ipa";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	soc: soc@0 {
		compatible = "simple-bus";
		ranges = <0 0 0 0 0x10 0>;
		dma-ranges = <0 0 0 0 0x10 0>;

		#address-cells = <2>;
		#size-cells = <2>;

		gcc: clock-controller@100000 {
			compatible = "qcom,sm8550-gcc";
			reg = <0 0x00100000 0 0x1f4200>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			clocks = <&bi_tcxo_div2>, <&sleep_clk>,
				 <&pcie0_phy>,
				 <&pcie1_phy>,
				 <&pcie_1_phy_aux_clk>,
				 <&ufs_mem_phy 0>,
				 <&ufs_mem_phy 1>,
				 <&ufs_mem_phy 2>,
				 <&usb_dp_qmpphy QMP_USB43DP_USB3_PIPE_CLK>;
		};

		ipcc: mailbox@408000 {
			compatible = "qcom,sm8550-ipcc", "qcom,ipcc";
			reg = <0 0x00408000 0 0x1000>;
			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-controller;
			#interrupt-cells = <3>;
			#mbox-cells = <2>;
		};

		gpi_dma2: dma-controller@800000 {
			compatible = "qcom,sm8550-gpi-dma", "qcom,sm6350-gpi-dma";
			#dma-cells = <3>;
			reg = <0 0x00800000 0 0x60000>;
			interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>;
			dma-channels = <12>;
			dma-channel-mask = <0x3e>;
			iommus = <&apps_smmu 0x436 0>;
			status = "disabled";
		};

		qupv3_id_1: geniqup@8c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x008c0000 0 0x2000>;
			ranges;
			clock-names = "m-ahb", "s-ahb";
			clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
			iommus = <&apps_smmu 0x423 0>;
			#address-cells = <2>;
			#size-cells = <2>;
			status = "disabled";

			i2c8: i2c@880000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00880000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c8_data_clk>;
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 0 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi8: spi@880000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00880000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 0 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c9: i2c@884000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00884000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c9_data_clk>;
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 1 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi9: spi@884000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00884000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 1 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c10: i2c@888000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00888000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c10_data_clk>;
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 2 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi10: spi@888000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00888000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 2 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c11: i2c@88c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0088c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c11_data_clk>;
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi11: spi@88c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0088c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c12: i2c@890000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00890000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c12_data_clk>;
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 4 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi12: spi@890000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00890000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 4 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c13: i2c@894000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c13_data_clk>;
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 5 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi13: spi@894000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 5 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart14: serial@898000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x898000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart14_default>, <&qup_uart14_cts_rts>;
				interrupts = <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c15: i2c@89c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0089c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c15_data_clk>;
				interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 7 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 7 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi15: spi@89c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0089c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>;
				interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma2 0 7 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 7 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};
		};

		i2c_master_hub_0: geniqup@9c0000 {
			compatible = "qcom,geni-se-i2c-master-hub";
			reg = <0x0 0x009c0000 0x0 0x2000>;
			clock-names = "s-ahb";
			clocks = <&gcc GCC_QUPV3_I2C_S_AHB_CLK>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			status = "disabled";

			i2c_hub_0: i2c@980000 {
				compatible = "qcom,geni-i2c-master-hub";
				reg = <0x0 0x00980000 0x0 0x4000>;
				clock-names = "se", "core";
				clocks = <&gcc GCC_QUPV3_I2C_S0_CLK>,
					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&hub_i2c0_data_clk>;
				interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c_hub_1: i2c@984000 {
				compatible = "qcom,geni-i2c-master-hub";
				reg = <0x0 0x00984000 0x0 0x4000>;
				clock-names = "se", "core";
				clocks = <&gcc GCC_QUPV3_I2C_S1_CLK>,
					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&hub_i2c1_data_clk>;
				interrupts = <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c_hub_2: i2c@988000 {
				compatible = "qcom,geni-i2c-master-hub";
				reg = <0x0 0x00988000 0x0 0x4000>;
				clock-names = "se", "core";
				clocks = <&gcc GCC_QUPV3_I2C_S2_CLK>,
					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&hub_i2c2_data_clk>;
				interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c_hub_3: i2c@98c000 {
				compatible = "qcom,geni-i2c-master-hub";
				reg = <0x0 0x0098c000 0x0 0x4000>;
				clock-names = "se", "core";
				clocks = <&gcc GCC_QUPV3_I2C_S3_CLK>,
					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&hub_i2c3_data_clk>;
				interrupts = <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c_hub_4: i2c@990000 {
				compatible = "qcom,geni-i2c-master-hub";
				reg = <0x0 0x00990000 0x0 0x4000>;
				clock-names = "se", "core";
				clocks = <&gcc GCC_QUPV3_I2C_S4_CLK>,
					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&hub_i2c4_data_clk>;
				interrupts = <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c_hub_5: i2c@994000 {
				compatible = "qcom,geni-i2c-master-hub";
				reg = <0 0x00994000 0 0x4000>;
				clock-names = "se", "core";
				clocks = <&gcc GCC_QUPV3_I2C_S5_CLK>,
					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&hub_i2c5_data_clk>;
				interrupts = <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c_hub_6: i2c@998000 {
				compatible = "qcom,geni-i2c-master-hub";
				reg = <0 0x00998000 0 0x4000>;
				clock-names = "se", "core";
				clocks = <&gcc GCC_QUPV3_I2C_S6_CLK>,
					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&hub_i2c6_data_clk>;
				interrupts = <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c_hub_7: i2c@99c000 {
				compatible = "qcom,geni-i2c-master-hub";
				reg = <0 0x0099c000 0 0x4000>;
				clock-names = "se", "core";
				clocks = <&gcc GCC_QUPV3_I2C_S7_CLK>,
					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&hub_i2c7_data_clk>;
				interrupts = <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c_hub_8: i2c@9a0000 {
				compatible = "qcom,geni-i2c-master-hub";
				reg = <0 0x009a0000 0 0x4000>;
				clock-names = "se", "core";
				clocks = <&gcc GCC_QUPV3_I2C_S8_CLK>,
					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&hub_i2c8_data_clk>;
				interrupts = <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c_hub_9: i2c@9a4000 {
				compatible = "qcom,geni-i2c-master-hub";
				reg = <0 0x009a4000 0 0x4000>;
				clock-names = "se", "core";
				clocks = <&gcc GCC_QUPV3_I2C_S9_CLK>,
					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&hub_i2c9_data_clk>;
				interrupts = <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};
		};

		gpi_dma1: dma-controller@a00000 {
			compatible = "qcom,sm8550-gpi-dma", "qcom,sm6350-gpi-dma";
			#dma-cells = <3>;
			reg = <0 0x00a00000 0 0x60000>;
			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
			dma-channels = <12>;
			dma-channel-mask = <0x1e>;
			iommus = <&apps_smmu 0xb6 0>;
			status = "disabled";
		};

		qupv3_id_0: geniqup@ac0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x00ac0000 0 0x2000>;
			ranges;
			clock-names = "m-ahb", "s-ahb";
			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
			iommus = <&apps_smmu 0xa3 0>;
			interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>;
			interconnect-names = "qup-core";
			#address-cells = <2>;
			#size-cells = <2>;
			status = "disabled";

			i2c0: i2c@a80000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a80000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c0_data_clk>;
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi0: spi@a80000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a80000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c1: i2c@a84000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a84000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c1_data_clk>;
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi1: spi@a84000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a84000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c2: i2c@a88000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a88000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c2_data_clk>;
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi2: spi@a88000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a88000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c3: i2c@a8c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a8c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c3_data_clk>;
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi3: spi@a8c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a8c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c4: i2c@a90000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a90000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c4_data_clk>;
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi4: spi@a90000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a90000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c5: i2c@a94000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a94000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c5_data_clk>;
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi5: spi@a94000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a94000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c6: i2c@a98000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a98000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c6_data_clk>;
				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 6 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi6: spi@a98000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a98000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 6 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart7: serial@a9c000 {
				compatible = "qcom,geni-debug-uart";
				reg = <0 0x00a9c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart7_default>;
				interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
				interconnect-names = "qup-core", "qup-config";
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
				status = "disabled";
			};
		};

		cnoc_main: interconnect@1500000 {
			compatible = "qcom,sm8550-cnoc-main";
			reg = <0 0x01500000 0 0x13080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		config_noc: interconnect@1600000 {
			compatible = "qcom,sm8550-config-noc";
			reg = <0 0x01600000 0 0x6200>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		system_noc: interconnect@1680000 {
			compatible = "qcom,sm8550-system-noc";
			reg = <0 0x01680000 0 0x1d080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		pcie_noc: interconnect@16c0000 {
			compatible = "qcom,sm8550-pcie-anoc";
			reg = <0 0x016c0000 0 0x12200>;
			#interconnect-cells = <2>;
			clocks = <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>,
				 <&gcc GCC_CFG_NOC_PCIE_ANOC_AHB_CLK>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		aggre1_noc: interconnect@16e0000 {
			compatible = "qcom,sm8550-aggre1-noc";
			reg = <0 0x016e0000 0 0x14400>;
			#interconnect-cells = <2>;
			clocks = <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		aggre2_noc: interconnect@1700000 {
			compatible = "qcom,sm8550-aggre2-noc";
			reg = <0 0x01700000 0 0x1e400>;
			#interconnect-cells = <2>;
			clocks = <&rpmhcc RPMH_IPA_CLK>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		mmss_noc: interconnect@1780000 {
			compatible = "qcom,sm8550-mmss-noc";
			reg = <0 0x01780000 0 0x5b800>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		rng: rng@10c3000 {
			compatible = "qcom,sm8550-trng", "qcom,trng";
			reg = <0 0x010c3000 0 0x1000>;
		};

		pcie0: pcie@1c00000 {
			device_type = "pci";
			compatible = "qcom,pcie-sm8550";
			reg = <0 0x01c00000 0 0x3000>,
			      <0 0x60000000 0 0xf1d>,
			      <0 0x60000f20 0 0xa8>,
			      <0 0x60001000 0 0x1000>,
			      <0 0x60100000 0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>,
				 <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <0>;
			num-lanes = <2>;

			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0",
					  "msi1",
					  "msi2",
					  "msi3",
					  "msi4",
					  "msi5",
					  "msi6",
					  "msi7";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_QTB_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr";

			interconnects = <&pcie_noc MASTER_PCIE_0 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_0 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			msi-map = <0x0 &gic_its 0x1400 0x1>,
				  <0x100 &gic_its 0x1401 0x1>;
			iommu-map = <0x0   &apps_smmu 0x1400 0x1>,
				    <0x100 &apps_smmu 0x1401 0x1>;

			resets = <&gcc GCC_PCIE_0_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_0_GDSC>;

			phys = <&pcie0_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie0_phy: phy@1c06000 {
			compatible = "qcom,sm8550-qmp-gen3x2-pcie-phy";
			reg = <0 0x01c06000 0 0x2000>;

			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
				 <&tcsr TCSR_PCIE_0_CLKREF_EN>,
				 <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_0_PIPE_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe";

			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_0_PHY_GDSC>;

			#clock-cells = <0>;
			clock-output-names = "pcie0_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie1: pcie@1c08000 {
			device_type = "pci";
			compatible = "qcom,pcie-sm8550";
			reg = <0x0 0x01c08000 0x0 0x3000>,
			      <0x0 0x40000000 0x0 0xf1d>,
			      <0x0 0x40000f20 0x0 0xa8>,
			      <0x0 0x40001000 0x0 0x1000>,
			      <0x0 0x40100000 0x0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <1>;
			num-lanes = <2>;

			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0",
					  "msi1",
					  "msi2",
					  "msi3",
					  "msi4",
					  "msi5",
					  "msi6",
					  "msi7";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_QTB_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>,
				 <&gcc GCC_CNOC_PCIE_SF_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr",
				      "cnoc_sf_axi";

			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&pcie_noc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_1 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			msi-map = <0x0 &gic_its 0x1480 0x1>,
				  <0x100 &gic_its 0x1481 0x1>;
			iommu-map = <0x0   &apps_smmu 0x1480 0x1>,
				    <0x100 &apps_smmu 0x1481 0x1>;

			resets = <&gcc GCC_PCIE_1_BCR>,
				<&gcc GCC_PCIE_1_LINK_DOWN_BCR>;
			reset-names = "pci", "link_down";

			power-domains = <&gcc PCIE_1_GDSC>;

			phys = <&pcie1_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie1_phy: phy@1c0e000 {
			compatible = "qcom,sm8550-qmp-gen4x2-pcie-phy";
			reg = <0x0 0x01c0e000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_1_PHY_AUX_CLK>,
				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
				 <&tcsr TCSR_PCIE_1_CLKREF_EN>,
				 <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_1_PIPE_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe";

			resets = <&gcc GCC_PCIE_1_PHY_BCR>,
				 <&gcc GCC_PCIE_1_NOCSR_COM_PHY_BCR>;
			reset-names = "phy", "phy_nocsr";

			assigned-clocks = <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_1_PHY_GDSC>;

			#clock-cells = <0>;
			clock-output-names = "pcie1_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		cryptobam: dma-controller@1dc4000 {
			compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
			reg = <0x0 0x01dc4000 0x0 0x28000>;
			interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
			#dma-cells = <1>;
			qcom,ee = <0>;
			qcom,controlled-remotely;
			iommus = <&apps_smmu 0x480 0x0>,
				 <&apps_smmu 0x481 0x0>;
		};

		crypto: crypto@1dfa000 {
			compatible = "qcom,sm8550-qce", "qcom,sm8150-qce", "qcom,qce";
			reg = <0x0 0x01dfa000 0x0 0x6000>;
			dmas = <&cryptobam 4>, <&cryptobam 5>;
			dma-names = "rx", "tx";
			iommus = <&apps_smmu 0x480 0x0>,
				 <&apps_smmu 0x481 0x0>;
			interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
			interconnect-names = "memory";
		};

		ufs_mem_phy: phy@1d80000 {
			compatible = "qcom,sm8550-qmp-ufs-phy";
			reg = <0x0 0x01d80000 0x0 0x2000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
				 <&tcsr TCSR_UFS_CLKREF_EN>;
			clock-names = "ref",
				      "ref_aux",
				      "qref";

			power-domains = <&gcc UFS_MEM_PHY_GDSC>;

			resets = <&ufs_mem_hc 0>;
			reset-names = "ufsphy";

			#clock-cells = <1>;
			#phy-cells = <0>;

			status = "disabled";
		};

		ufs_mem_hc: ufs@1d84000 {
			compatible = "qcom,sm8550-ufshc", "qcom,ufshc",
				     "jedec,ufs-2.0";
			reg = <0x0 0x01d84000 0x0 0x3000>;
			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
			phys = <&ufs_mem_phy>;
			phy-names = "ufsphy";
			lanes-per-direction = <2>;
			#reset-cells = <1>;
			resets = <&gcc GCC_UFS_PHY_BCR>;
			reset-names = "rst";

			power-domains = <&gcc UFS_PHY_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			iommus = <&apps_smmu 0x60 0x0>;
			dma-coherent;

			operating-points-v2 = <&ufs_opp_table>;
			interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>;

			interconnect-names = "ufs-ddr", "cpu-ufs";
			clock-names = "core_clk",
				      "bus_aggr_clk",
				      "iface_clk",
				      "core_clk_unipro",
				      "ref_clk",
				      "tx_lane0_sync_clk",
				      "rx_lane0_sync_clk",
				      "rx_lane1_sync_clk";
			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
				 <&gcc GCC_UFS_PHY_AHB_CLK>,
				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
				 <&tcsr TCSR_UFS_PAD_CLKREF_EN>,
				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
			qcom,ice = <&ice>;

			status = "disabled";

			ufs_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-75000000 {
					opp-hz = /bits/ 64 <75000000>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <75000000>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>;
					required-opps = <&rpmhpd_opp_low_svs>;
				};

				opp-150000000 {
					opp-hz = /bits/ 64 <150000000>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <150000000>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>;
					required-opps = <&rpmhpd_opp_svs>;
				};

				opp-300000000 {
					opp-hz = /bits/ 64 <300000000>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <300000000>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>;
					required-opps = <&rpmhpd_opp_nom>;
				};
			};
		};

		ice: crypto@1d88000 {
			compatible = "qcom,sm8550-inline-crypto-engine",
				     "qcom,inline-crypto-engine";
			reg = <0 0x01d88000 0 0x8000>;
			clocks = <&gcc GCC_UFS_PHY_ICE_CORE_CLK>;
		};

		tcsr_mutex: hwlock@1f40000 {
			compatible = "qcom,tcsr-mutex";
			reg = <0 0x01f40000 0 0x20000>;
			#hwlock-cells = <1>;
		};

		tcsr: clock-controller@1fc0000 {
			compatible = "qcom,sm8550-tcsr", "syscon";
			reg = <0 0x01fc0000 0 0x30000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		gpu: gpu@3d00000 {
			compatible = "qcom,adreno-43050a01", "qcom,adreno";
			reg = <0x0 0x03d00000 0x0 0x40000>,
			      <0x0 0x03d9e000 0x0 0x1000>,
			      <0x0 0x03d61000 0x0 0x800>;
			reg-names = "kgsl_3d0_reg_memory",
				    "cx_mem",
				    "cx_dbgc";

			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;

			iommus = <&adreno_smmu 0 0x0>,
				 <&adreno_smmu 1 0x0>;

			operating-points-v2 = <&gpu_opp_table>;

			qcom,gmu = <&gmu>;
			#cooling-cells = <2>;

			status = "disabled";

			zap-shader {
				memory-region = <&gpu_micro_code_mem>;
			};

			/* Speedbin needs more work on A740+, keep only lower freqs */
			gpu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-680000000 {
					opp-hz = /bits/ 64 <680000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
				};

				opp-615000000 {
					opp-hz = /bits/ 64 <615000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L0>;
				};

				opp-550000000 {
					opp-hz = /bits/ 64 <550000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
				};

				opp-475000000 {
					opp-hz = /bits/ 64 <475000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_L1>;
				};

				opp-401000000 {
					opp-hz = /bits/ 64 <401000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
				};

				opp-348000000 {
					opp-hz = /bits/ 64 <348000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D0>;
				};

				opp-295000000 {
					opp-hz = /bits/ 64 <295000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
				};

				opp-220000000 {
					opp-hz = /bits/ 64 <220000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D2>;
				};
			};
		};

		gmu: gmu@3d6a000 {
			compatible = "qcom,adreno-gmu-740.1", "qcom,adreno-gmu";
			reg = <0x0 0x03d6a000 0x0 0x35000>,
			      <0x0 0x03d50000 0x0 0x10000>,
			      <0x0 0x0b280000 0x0 0x10000>;
			reg-names = "gmu", "rscc", "gmu_pdc";

			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hfi", "gmu";

			clocks = <&gpucc GPU_CC_AHB_CLK>,
				 <&gpucc GPU_CC_CX_GMU_CLK>,
				 <&gpucc GPU_CC_CXO_CLK>,
				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
				 <&gpucc GPU_CC_HUB_CX_INT_CLK>,
				 <&gpucc GPU_CC_DEMET_CLK>;
			clock-names = "ahb",
				      "gmu",
				      "cxo",
				      "axi",
				      "memnoc",
				      "hub",
				      "demet";

			power-domains = <&gpucc GPU_CC_CX_GDSC>,
					<&gpucc GPU_CC_GX_GDSC>;
			power-domain-names = "cx",
					     "gx";

			iommus = <&adreno_smmu 5 0x0>;

			qcom,qmp = <&aoss_qmp>;

			operating-points-v2 = <&gmu_opp_table>;

			gmu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-500000000 {
					opp-hz = /bits/ 64 <500000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
				};

				opp-200000000 {
					opp-hz = /bits/ 64 <200000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
				};
			};
		};

		gpucc: clock-controller@3d90000 {
			compatible = "qcom,sm8550-gpucc";
			reg = <0 0x03d90000 0 0xa000>;
			clocks = <&bi_tcxo_div2>,
				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		adreno_smmu: iommu@3da0000 {
			compatible = "qcom,sm8550-smmu-500", "qcom,adreno-smmu",
				     "qcom,smmu-500", "arm,mmu-500";
			reg = <0x0 0x03da0000 0x0 0x40000>;
			#iommu-cells = <2>;
			#global-interrupts = <1>;
			interrupts = <GIC_SPI 673 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 677 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 678 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 679 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 680 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 686 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 476 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 574 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 575 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 576 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 577 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 659 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 661 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 664 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 665 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 666 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 668 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 669 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 699 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>,
				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
				 <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>,
				 <&gpucc GPU_CC_AHB_CLK>;
			clock-names = "hlos",
				      "bus",
				      "iface",
				      "ahb";
			power-domains = <&gpucc GPU_CC_CX_GDSC>;
			dma-coherent;
		};

		ipa: ipa@3f40000 {
			compatible = "qcom,sm8550-ipa";

			iommus = <&apps_smmu 0x4a0 0x0>,
				 <&apps_smmu 0x4a2 0x0>;
			reg = <0 0x3f40000 0 0x10000>,
			      <0 0x3f50000 0 0x5000>,
			      <0 0x3e04000 0 0xfc000>;
			reg-names = "ipa-reg",
				    "ipa-shared",
				    "gsi";

			interrupts-extended = <&intc GIC_SPI 654 IRQ_TYPE_EDGE_RISING>,
					      <&intc GIC_SPI 432 IRQ_TYPE_LEVEL_HIGH>,
					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "ipa",
					  "gsi",
					  "ipa-clock-query",
					  "ipa-setup-ready";

			clocks = <&rpmhcc RPMH_IPA_CLK>;
			clock-names = "core";

			interconnects = <&aggre2_noc MASTER_IPA 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_IPA_CFG 0>;
			interconnect-names = "memory",
					     "config";

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&ipa_smp2p_out 0>,
					   <&ipa_smp2p_out 1>;
			qcom,smem-state-names = "ipa-clock-enabled-valid",
						"ipa-clock-enabled";

			status = "disabled";
		};

		remoteproc_mpss: remoteproc@4080000 {
			compatible = "qcom,sm8550-mpss-pas";
			reg = <0x0 0x04080000 0x0 0x4040>;

			interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_modem_in 7 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready", "handover",
					  "stop-ack", "shutdown-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd RPMHPD_CX>,
					<&rpmhpd RPMHPD_MSS>;
			power-domain-names = "cx", "mss";

			interconnects = <&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;

			memory-region = <&mpss_mem>, <&q6_mpss_dtb_mem>, <&mpss_dsm_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_modem_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_MPSS
						IPCC_MPROC_SIGNAL_GLINK_QMP>;
				label = "mpss";
				qcom,remote-pid = <1>;
			};
		};

		lpass_wsa2macro: codec@6aa0000 {
			compatible = "qcom,sm8550-lpass-wsa-macro";
			reg = <0 0x06aa0000 0 0x1000>;
			clocks = <&q6prmcc LPASS_CLK_ID_WSA2_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&lpass_vamacro>;
			clock-names = "mclk", "macro", "dcodec", "fsgen";

			#clock-cells = <0>;
			clock-output-names = "wsa2-mclk";
			#sound-dai-cells = <1>;
		};

		swr3: soundwire@6ab0000 {
			compatible = "qcom,soundwire-v2.0.0";
			reg = <0 0x06ab0000 0 0x10000>;
			interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&lpass_wsa2macro>;
			clock-names = "iface";
			label = "WSA2";

			pinctrl-0 = <&wsa2_swr_active>;
			pinctrl-names = "default";

			qcom,din-ports = <4>;
			qcom,dout-ports = <9>;

			qcom,ports-sinterval =		/bits/ 16 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x18f 0xff 0xff 0x0f 0x0f 0xff 0x31f>;
			qcom,ports-offset1 =		/bits/ 8 <0x01 0x03 0x05 0x02 0x04 0x15 0x00 0xff 0xff 0x06 0x0d 0xff 0x00>;
			qcom,ports-offset2 =		/bits/ 8 <0xff 0x07 0x1f 0xff 0x07 0x1f 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
			qcom,ports-word-length =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x18>;
			qcom,ports-block-pack-mode =	/bits/ 8 <0x00 0x01 0x01 0x00 0x01 0x01 0x00 0x00 0x00 0x01 0x01 0x00 0x00>;
			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-lane-control =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;

			#address-cells = <2>;
			#size-cells = <0>;
			#sound-dai-cells = <1>;
			status = "disabled";
		};

		lpass_rxmacro: codec@6ac0000 {
			compatible = "qcom,sm8550-lpass-rx-macro";
			reg = <0 0x06ac0000 0 0x1000>;
			clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&lpass_vamacro>;
			clock-names = "mclk", "macro", "dcodec", "fsgen";

			#clock-cells = <0>;
			clock-output-names = "mclk";
			#sound-dai-cells = <1>;
		};

		swr1: soundwire@6ad0000 {
			compatible = "qcom,soundwire-v2.0.0";
			reg = <0 0x06ad0000 0 0x10000>;
			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&lpass_rxmacro>;
			clock-names = "iface";
			label = "RX";

			pinctrl-0 = <&rx_swr_active>;
			pinctrl-names = "default";

			qcom,din-ports = <1>;
			qcom,dout-ports = <11>;

			qcom,ports-sinterval =		/bits/ 16 <0x03 0x3f 0x1f 0x07 0x00 0x18f 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0b 0x01 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0b 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-hstart =		/bits/ 8 <0xff 0x03 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-hstop =		/bits/ 8 <0xff 0x06 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xff 0xff 0x0f 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0x00 0x01 0xff 0xff 0x00 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff>;

			#address-cells = <2>;
			#size-cells = <0>;
			#sound-dai-cells = <1>;
			status = "disabled";
		};

		lpass_txmacro: codec@6ae0000 {
			compatible = "qcom,sm8550-lpass-tx-macro";
			reg = <0 0x06ae0000 0 0x1000>;
			clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&lpass_vamacro>;
			clock-names = "mclk", "macro", "dcodec", "fsgen";

			#clock-cells = <0>;
			clock-output-names = "mclk";
			#sound-dai-cells = <1>;
		};

		lpass_wsamacro: codec@6b00000 {
			compatible = "qcom,sm8550-lpass-wsa-macro";
			reg = <0 0x06b00000 0 0x1000>;
			clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&lpass_vamacro>;
			clock-names = "mclk", "macro", "dcodec", "fsgen";

			#clock-cells = <0>;
			clock-output-names = "mclk";
			#sound-dai-cells = <1>;
		};

		swr0: soundwire@6b10000 {
			compatible = "qcom,soundwire-v2.0.0";
			reg = <0 0x06b10000 0 0x10000>;
			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&lpass_wsamacro>;
			clock-names = "iface";
			label = "WSA";

			pinctrl-0 = <&wsa_swr_active>;
			pinctrl-names = "default";

			qcom,din-ports = <4>;
			qcom,dout-ports = <9>;

			qcom,ports-sinterval =		/bits/ 16 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x18f 0xff 0xff 0x0f 0x0f 0xff 0x31f>;
			qcom,ports-offset1 =		/bits/ 8 <0x01 0x03 0x05 0x02 0x04 0x15 0x00 0xff 0xff 0x06 0x0d 0xff 0x00>;
			qcom,ports-offset2 =		/bits/ 8 <0xff 0x07 0x1f 0xff 0x07 0x1f 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
			qcom,ports-word-length =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x18>;
			qcom,ports-block-pack-mode =	/bits/ 8 <0x00 0x01 0x01 0x00 0x01 0x01 0x00 0x00 0x00 0x01 0x01 0x00 0x00>;
			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-lane-control =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;

			#address-cells = <2>;
			#size-cells = <0>;
			#sound-dai-cells = <1>;
			status = "disabled";
		};

		swr2: soundwire@6d30000 {
			compatible = "qcom,soundwire-v2.0.0";
			reg = <0 0x06d30000 0 0x10000>;
			interrupts = <GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "core", "wakeup";
			clocks = <&lpass_txmacro>;
			clock-names = "iface";
			label = "TX";

			pinctrl-0 = <&tx_swr_active>;
			pinctrl-names = "default";

			qcom,din-ports = <4>;
			qcom,dout-ports = <0>;
			qcom,ports-sinterval-low =	/bits/ 8 <0x01 0x01 0x03 0x03>;
			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x01 0x01>;
			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x00 0x00>;
			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff 0xff>;
			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff 0xff>;
			qcom,ports-word-length =	/bits/ 8 <0xff 0xff 0xff 0xff>;
			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0xff 0xff 0xff>;
			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff>;
			qcom,ports-lane-control =	/bits/ 8 <0x01 0x02 0x00 0x00>;

			#address-cells = <2>;
			#size-cells = <0>;
			#sound-dai-cells = <1>;
			status = "disabled";
		};

		lpass_vamacro: codec@6d44000 {
			compatible = "qcom,sm8550-lpass-va-macro";
			reg = <0 0x06d44000 0 0x1000>;
			clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			clock-names = "mclk", "macro", "dcodec";

			#clock-cells = <0>;
			clock-output-names = "fsgen";
			#sound-dai-cells = <1>;
		};

		lpass_tlmm: pinctrl@6e80000 {
			compatible = "qcom,sm8550-lpass-lpi-pinctrl";
			reg = <0 0x06e80000 0 0x20000>,
			      <0 0x07250000 0 0x10000>;
			gpio-controller;
			#gpio-cells = <2>;
			gpio-ranges = <&lpass_tlmm 0 0 23>;

			clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			clock-names = "core", "audio";

			tx_swr_active: tx-swr-active-state {
				clk-pins {
					pins = "gpio0";
					function = "swr_tx_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data-pins {
					pins = "gpio1", "gpio2", "gpio14";
					function = "swr_tx_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;
				};
			};

			rx_swr_active: rx-swr-active-state {
				clk-pins {
					pins = "gpio3";
					function = "swr_rx_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data-pins {
					pins = "gpio4", "gpio5";
					function = "swr_rx_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;
				};
			};

			dmic01_default: dmic01-default-state {
				clk-pins {
					pins = "gpio6";
					function = "dmic1_clk";
					drive-strength = <8>;
					output-high;
				};

				data-pins {
					pins = "gpio7";
					function = "dmic1_data";
					drive-strength = <8>;
					input-enable;
				};
			};

			dmic23_default: dmic23-default-state {
				clk-pins {
					pins = "gpio8";
					function = "dmic2_clk";
					drive-strength = <8>;
					output-high;
				};

				data-pins {
					pins = "gpio9";
					function = "dmic2_data";
					drive-strength = <8>;
					input-enable;
				};
			};

			wsa_swr_active: wsa-swr-active-state {
				clk-pins {
					pins = "gpio10";
					function = "wsa_swr_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data-pins {
					pins = "gpio11";
					function = "wsa_swr_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;
				};
			};

			wsa2_swr_active: wsa2-swr-active-state {
				clk-pins {
					pins = "gpio15";
					function = "wsa2_swr_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data-pins {
					pins = "gpio16";
					function = "wsa2_swr_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;
				};
			};
		};

		lpass_lpiaon_noc: interconnect@7400000 {
			compatible = "qcom,sm8550-lpass-lpiaon-noc";
			reg = <0 0x07400000 0 0x19080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		lpass_lpicx_noc: interconnect@7430000 {
			compatible = "qcom,sm8550-lpass-lpicx-noc";
			reg = <0 0x07430000 0 0x3a200>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		lpass_ag_noc: interconnect@7e40000 {
			compatible = "qcom,sm8550-lpass-ag-noc";
			reg = <0 0x07e40000 0 0xe080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		sdhc_2: mmc@8804000 {
			compatible = "qcom,sm8550-sdhci", "qcom,sdhci-msm-v5";
			reg = <0 0x08804000 0 0x1000>;

			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";

			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
				 <&gcc GCC_SDCC2_APPS_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "iface", "core", "xo";
			iommus = <&apps_smmu 0x540 0>;
			qcom,dll-config = <0x0007642c>;
			qcom,ddr-config = <0x80040868>;
			power-domains = <&rpmhpd RPMHPD_CX>;
			operating-points-v2 = <&sdhc2_opp_table>;

			interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
			interconnect-names = "sdhc-ddr", "cpu-sdhc";
			bus-width = <4>;
			dma-coherent;

			/* Forbid SDR104/SDR50 - broken hw! */
			sdhci-caps-mask = <0x3 0>;

			status = "disabled";

			sdhc2_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-19200000 {
					opp-hz = /bits/ 64 <19200000>;
					required-opps = <&rpmhpd_opp_min_svs>;
				};

				opp-50000000 {
					opp-hz = /bits/ 64 <50000000>;
					required-opps = <&rpmhpd_opp_low_svs>;
				};

				opp-100000000 {
					opp-hz = /bits/ 64 <100000000>;
					required-opps = <&rpmhpd_opp_svs>;
				};

				opp-202000000 {
					opp-hz = /bits/ 64 <202000000>;
					required-opps = <&rpmhpd_opp_svs_l1>;
				};
			};
		};

		videocc: clock-controller@aaf0000 {
			compatible = "qcom,sm8550-videocc";
			reg = <0 0x0aaf0000 0 0x10000>;
			clocks = <&bi_tcxo_div2>,
				 <&gcc GCC_VIDEO_AHB_CLK>;
			power-domains = <&rpmhpd RPMHPD_MMCX>;
			required-opps = <&rpmhpd_opp_low_svs>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		camcc: clock-controller@ade0000 {
			compatible = "qcom,sm8550-camcc";
			reg = <0 0x0ade0000 0 0x20000>;
			clocks = <&gcc GCC_CAMERA_AHB_CLK>,
				 <&bi_tcxo_div2>,
				 <&bi_tcxo_ao_div2>,
				 <&sleep_clk>;
			power-domains = <&rpmhpd SM8550_MMCX>;
			required-opps = <&rpmhpd_opp_low_svs>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		mdss: display-subsystem@ae00000 {
			compatible = "qcom,sm8550-mdss";
			reg = <0 0x0ae00000 0 0x1000>;
			reg-names = "mdss";

			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-controller;
			#interrupt-cells = <1>;

			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
				 <&gcc GCC_DISP_AHB_CLK>,
				 <&gcc GCC_DISP_HF_AXI_CLK>,
				 <&dispcc DISP_CC_MDSS_MDP_CLK>;

			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;

			power-domains = <&dispcc MDSS_GDSC>;

			interconnects = <&mmss_noc MASTER_MDP 0 &gem_noc SLAVE_LLCC 0>,
					<&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;
			interconnect-names = "mdp0-mem", "mdp1-mem";

			iommus = <&apps_smmu 0x1c00 0x2>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			mdss_mdp: display-controller@ae01000 {
				compatible = "qcom,sm8550-dpu";
				reg = <0 0x0ae01000 0 0x8f000>,
				      <0 0x0aeb0000 0 0x2008>;
				reg-names = "mdp", "vbif";

				interrupt-parent = <&mdss>;
				interrupts = <0>;

				clocks = <&gcc GCC_DISP_AHB_CLK>,
					 <&gcc GCC_DISP_HF_AXI_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
				clock-names = "bus",
					      "nrt_bus",
					      "iface",
					      "lut",
					      "core",
					      "vsync";

				power-domains = <&rpmhpd RPMHPD_MMCX>;

				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
				assigned-clock-rates = <19200000>;

				operating-points-v2 = <&mdp_opp_table>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dpu_intf1_out: endpoint {
							remote-endpoint = <&mdss_dsi0_in>;
						};
					};

					port@1 {
						reg = <1>;
						dpu_intf2_out: endpoint {
							remote-endpoint = <&mdss_dsi1_in>;
						};
					};

					port@2 {
						reg = <2>;
						dpu_intf0_out: endpoint {
							remote-endpoint = <&mdss_dp0_in>;
						};
					};
				};

				mdp_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-200000000 {
						opp-hz = /bits/ 64 <200000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-325000000 {
						opp-hz = /bits/ 64 <325000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-375000000 {
						opp-hz = /bits/ 64 <375000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-514000000 {
						opp-hz = /bits/ 64 <514000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss_dp0: displayport-controller@ae90000 {
				compatible = "qcom,sm8550-dp", "qcom,sm8350-dp";
				reg = <0 0xae90000 0 0x200>,
				      <0 0xae90200 0 0x200>,
				      <0 0xae90400 0 0xc00>,
				      <0 0xae91000 0 0x400>,
				      <0 0xae91400 0 0x400>;
				interrupt-parent = <&mdss>;
				interrupts = <12>;
				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc DISP_CC_MDSS_DPTX0_AUX_CLK>,
					 <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK>,
					 <&dispcc DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK>;
				clock-names = "core_iface",
					      "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface",
					      "stream_pixel";

				assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>,
						  <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>;
				assigned-clock-parents = <&usb_dp_qmpphy QMP_USB43DP_DP_LINK_CLK>,
							 <&usb_dp_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;

				phys = <&usb_dp_qmpphy QMP_USB43DP_DP_PHY>;
				phy-names = "dp";

				#sound-dai-cells = <0>;

				operating-points-v2 = <&dp_opp_table>;
				power-domains = <&rpmhpd RPMHPD_MMCX>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dp0_in: endpoint {
							remote-endpoint = <&dpu_intf0_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dp0_out: endpoint {
						};
					};
				};

				dp_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-162000000 {
						opp-hz = /bits/ 64 <162000000>;
						required-opps = <&rpmhpd_opp_low_svs_d1>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss_dsi0: dsi@ae94000 {
				compatible = "qcom,sm8550-dsi-ctrl", "qcom,mdss-dsi-ctrl";
				reg = <0 0x0ae94000 0 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <4>;

				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&gcc GCC_DISP_HF_AXI_CLK>;
				clock-names = "byte",
					      "byte_intf",
					      "pixel",
					      "core",
					      "iface",
					      "bus";

				power-domains = <&rpmhpd RPMHPD_MMCX>;

				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
						  <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
				assigned-clock-parents = <&mdss_dsi0_phy 0>,
							 <&mdss_dsi0_phy 1>;

				operating-points-v2 = <&mdss_dsi_opp_table>;

				phys = <&mdss_dsi0_phy>;
				phy-names = "dsi";

				#address-cells = <1>;
				#size-cells = <0>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dsi0_in: endpoint {
							remote-endpoint = <&dpu_intf1_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dsi0_out: endpoint {
						};
					};
				};

				mdss_dsi_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-187500000 {
						opp-hz = /bits/ 64 <187500000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-300000000 {
						opp-hz = /bits/ 64 <300000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-358000000 {
						opp-hz = /bits/ 64 <358000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};
				};
			};

			mdss_dsi0_phy: phy@ae95000 {
				compatible = "qcom,sm8550-dsi-phy-4nm";
				reg = <0 0x0ae95000 0 0x200>,
				      <0 0x0ae95200 0 0x280>,
				      <0 0x0ae95500 0 0x400>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&rpmhcc RPMH_CXO_CLK>;
				clock-names = "iface", "ref";

				#clock-cells = <1>;
				#phy-cells = <0>;

				status = "disabled";
			};

			mdss_dsi1: dsi@ae96000 {
				compatible = "qcom,sm8550-dsi-ctrl", "qcom,mdss-dsi-ctrl";
				reg = <0 0x0ae96000 0 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <5>;

				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&gcc GCC_DISP_HF_AXI_CLK>;
				clock-names = "byte",
					      "byte_intf",
					      "pixel",
					      "core",
					      "iface",
					      "bus";

				power-domains = <&rpmhpd RPMHPD_MMCX>;

				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>,
						  <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
				assigned-clock-parents = <&mdss_dsi1_phy 0>,
							 <&mdss_dsi1_phy 1>;

				operating-points-v2 = <&mdss_dsi_opp_table>;

				phys = <&mdss_dsi1_phy>;
				phy-names = "dsi";

				#address-cells = <1>;
				#size-cells = <0>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dsi1_in: endpoint {
							remote-endpoint = <&dpu_intf2_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dsi1_out: endpoint {
						};
					};
				};
			};

			mdss_dsi1_phy: phy@ae97000 {
				compatible = "qcom,sm8550-dsi-phy-4nm";
				reg = <0 0x0ae97000 0 0x200>,
				      <0 0x0ae97200 0 0x280>,
				      <0 0x0ae97500 0 0x400>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&rpmhcc RPMH_CXO_CLK>;
				clock-names = "iface", "ref";

				#clock-cells = <1>;
				#phy-cells = <0>;

				status = "disabled";
			};
		};

		dispcc: clock-controller@af00000 {
			compatible = "qcom,sm8550-dispcc";
			reg = <0 0x0af00000 0 0x20000>;
			clocks = <&bi_tcxo_div2>,
				 <&bi_tcxo_ao_div2>,
				 <&gcc GCC_DISP_AHB_CLK>,
				 <&sleep_clk>,
				 <&mdss_dsi0_phy 0>,
				 <&mdss_dsi0_phy 1>,
				 <&mdss_dsi1_phy 0>,
				 <&mdss_dsi1_phy 1>,
				 <&usb_dp_qmpphy QMP_USB43DP_DP_LINK_CLK>,
				 <&usb_dp_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
				 <0>, /* dp1 */
				 <0>,
				 <0>, /* dp2 */
				 <0>,
				 <0>, /* dp3 */
				 <0>;
			power-domains = <&rpmhpd RPMHPD_MMCX>;
			required-opps = <&rpmhpd_opp_low_svs>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		usb_1_hsphy: phy@88e3000 {
			compatible = "qcom,sm8550-snps-eusb2-phy";
			reg = <0x0 0x088e3000 0x0 0x154>;
			#phy-cells = <0>;

			clocks = <&tcsr TCSR_USB2_CLKREF_EN>;
			clock-names = "ref";

			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;

			status = "disabled";
		};

		usb_dp_qmpphy: phy@88e8000 {
			compatible = "qcom,sm8550-qmp-usb3-dp-phy";
			reg = <0x0 0x088e8000 0x0 0x3000>;

			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
			clock-names = "aux", "ref", "com_aux", "usb3_pipe";

			power-domains = <&gcc USB3_PHY_GDSC>;

			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
			reset-names = "phy", "common";

			#clock-cells = <1>;
			#phy-cells = <1>;

			status = "disabled";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;

					usb_dp_qmpphy_out: endpoint {
					};
				};

				port@1 {
					reg = <1>;

					usb_dp_qmpphy_usb_ss_in: endpoint {
					};
				};

				port@2 {
					reg = <2>;

					usb_dp_qmpphy_dp_in: endpoint {
					};
				};
			};
		};

		usb_1: usb@a6f8800 {
			compatible = "qcom,sm8550-dwc3", "qcom,dwc3";
			reg = <0x0 0x0a6f8800 0x0 0x400>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
				 <&tcsr TCSR_USB3_CLKREF_EN>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "sleep",
				      "mock_utmi",
				      "xo";

			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
					      <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "pwr_event",
					  "hs_phy_irq",
					  "dp_hs_phy_irq",
					  "dm_hs_phy_irq",
					  "ss_phy_irq";

			power-domains = <&gcc USB30_PRIM_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			resets = <&gcc GCC_USB30_PRIM_BCR>;

			interconnects = <&aggre1_noc MASTER_USB3_0 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_0 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			status = "disabled";

			usb_1_dwc3: usb@a600000 {
				compatible = "snps,dwc3";
				reg = <0x0 0x0a600000 0x0 0xcd00>;
				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x40 0x0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
				snps,usb3_lpm_capable;
				phys = <&usb_1_hsphy>,
				       <&usb_dp_qmpphy QMP_USB43DP_USB3_PHY>;
				phy-names = "usb2-phy", "usb3-phy";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;

						usb_1_dwc3_hs: endpoint {
						};
					};

					port@1 {
						reg = <1>;

						usb_1_dwc3_ss: endpoint {
						};
					};
				};
			};
		};

		pdc: interrupt-controller@b220000 {
			compatible = "qcom,sm8550-pdc", "qcom,pdc";
			reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;
			qcom,pdc-ranges = <0 480 94>, <94 609 31>,
					  <125 63 1>, <126 716 12>,
					  <138 251 5>;
			#interrupt-cells = <2>;
			interrupt-parent = <&intc>;
			interrupt-controller;
		};

		tsens0: thermal-sensor@c271000 {
			compatible = "qcom,sm8550-tsens", "qcom,tsens-v2";
			reg = <0 0x0c271000 0 0x1000>, /* TM */
			      <0 0x0c222000 0 0x1000>; /* SROT */
			#qcom,sensors = <16>;
			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 640 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		tsens1: thermal-sensor@c272000 {
			compatible = "qcom,sm8550-tsens", "qcom,tsens-v2";
			reg = <0 0x0c272000 0 0x1000>, /* TM */
			      <0 0x0c223000 0 0x1000>; /* SROT */
			#qcom,sensors = <16>;
			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		tsens2: thermal-sensor@c273000 {
			compatible = "qcom,sm8550-tsens", "qcom,tsens-v2";
			reg = <0 0x0c273000 0 0x1000>, /* TM */
			      <0 0x0c224000 0 0x1000>; /* SROT */
			#qcom,sensors = <16>;
			interrupts = <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 642 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		aoss_qmp: power-management@c300000 {
			compatible = "qcom,sm8550-aoss-qmp", "qcom,aoss-qmp";
			reg = <0 0x0c300000 0 0x400>;
			interrupt-parent = <&ipcc>;
			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
						     IRQ_TYPE_EDGE_RISING>;
			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;

			#clock-cells = <0>;
		};

		sram@c3f0000 {
			compatible = "qcom,rpmh-stats";
			reg = <0 0x0c3f0000 0 0x400>;
		};

		spmi_bus: spmi@c400000 {
			compatible = "qcom,spmi-pmic-arb";
			reg = <0 0x0c400000 0 0x3000>,
			      <0 0x0c500000 0 0x400000>,
			      <0 0x0c440000 0 0x80000>,
			      <0 0x0c4c0000 0 0x20000>,
			      <0 0x0c42d000 0 0x4000>;
			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
			interrupt-names = "periph_irq";
			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
			qcom,ee = <0>;
			qcom,channel = <0>;
			qcom,bus-id = <0>;
			#address-cells = <2>;
			#size-cells = <0>;
			interrupt-controller;
			#interrupt-cells = <4>;
		};

		tlmm: pinctrl@f100000 {
			compatible = "qcom,sm8550-tlmm";
			reg = <0 0x0f100000 0 0x300000>;
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			gpio-ranges = <&tlmm 0 0 211>;
			wakeup-parent = <&pdc>;

			hub_i2c0_data_clk: hub-i2c0-data-clk-state {
				/* SDA, SCL */
				pins = "gpio16", "gpio17";
				function = "i2chub0_se0";
				drive-strength = <2>;
				bias-pull-up;
			};

			hub_i2c1_data_clk: hub-i2c1-data-clk-state {
				/* SDA, SCL */
				pins = "gpio18", "gpio19";
				function = "i2chub0_se1";
				drive-strength = <2>;
				bias-pull-up;
			};

			hub_i2c2_data_clk: hub-i2c2-data-clk-state {
				/* SDA, SCL */
				pins = "gpio20", "gpio21";
				function = "i2chub0_se2";
				drive-strength = <2>;
				bias-pull-up;
			};

			hub_i2c3_data_clk: hub-i2c3-data-clk-state {
				/* SDA, SCL */
				pins = "gpio22", "gpio23";
				function = "i2chub0_se3";
				drive-strength = <2>;
				bias-pull-up;
			};

			hub_i2c4_data_clk: hub-i2c4-data-clk-state {
				/* SDA, SCL */
				pins = "gpio4", "gpio5";
				function = "i2chub0_se4";
				drive-strength = <2>;
				bias-pull-up;
			};

			hub_i2c5_data_clk: hub-i2c5-data-clk-state {
				/* SDA, SCL */
				pins = "gpio6", "gpio7";
				function = "i2chub0_se5";
				drive-strength = <2>;
				bias-pull-up;
			};

			hub_i2c6_data_clk: hub-i2c6-data-clk-state {
				/* SDA, SCL */
				pins = "gpio8", "gpio9";
				function = "i2chub0_se6";
				drive-strength = <2>;
				bias-pull-up;
			};

			hub_i2c7_data_clk: hub-i2c7-data-clk-state {
				/* SDA, SCL */
				pins = "gpio10", "gpio11";
				function = "i2chub0_se7";
				drive-strength = <2>;
				bias-pull-up;
			};

			hub_i2c8_data_clk: hub-i2c8-data-clk-state {
				/* SDA, SCL */
				pins = "gpio206", "gpio207";
				function = "i2chub0_se8";
				drive-strength = <2>;
				bias-pull-up;
			};

			hub_i2c9_data_clk: hub-i2c9-data-clk-state {
				/* SDA, SCL */
				pins = "gpio84", "gpio85";
				function = "i2chub0_se9";
				drive-strength = <2>;
				bias-pull-up;
			};

			pcie0_default_state: pcie0-default-state {
				perst-pins {
					pins = "gpio94";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};

				clkreq-pins {
					pins = "gpio95";
					function = "pcie0_clk_req_n";
					drive-strength = <2>;
					bias-pull-up;
				};

				wake-pins {
					pins = "gpio96";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			pcie1_default_state: pcie1-default-state {
				perst-pins {
					pins = "gpio97";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};

				clkreq-pins {
					pins = "gpio98";
					function = "pcie1_clk_req_n";
					drive-strength = <2>;
					bias-pull-up;
				};

				wake-pins {
					pins = "gpio99";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			qup_i2c0_data_clk: qup-i2c0-data-clk-state {
				/* SDA, SCL */
				pins = "gpio28", "gpio29";
				function = "qup1_se0";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c1_data_clk: qup-i2c1-data-clk-state {
				/* SDA, SCL */
				pins = "gpio32", "gpio33";
				function = "qup1_se1";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c2_data_clk: qup-i2c2-data-clk-state {
				/* SDA, SCL */
				pins = "gpio36", "gpio37";
				function = "qup1_se2";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c3_data_clk: qup-i2c3-data-clk-state {
				/* SDA, SCL */
				pins = "gpio40", "gpio41";
				function = "qup1_se3";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c4_data_clk: qup-i2c4-data-clk-state {
				/* SDA, SCL */
				pins = "gpio44", "gpio45";
				function = "qup1_se4";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c5_data_clk: qup-i2c5-data-clk-state {
				/* SDA, SCL */
				pins = "gpio52", "gpio53";
				function = "qup1_se5";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c6_data_clk: qup-i2c6-data-clk-state {
				/* SDA, SCL */
				pins = "gpio48", "gpio49";
				function = "qup1_se6";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c8_data_clk: qup-i2c8-data-clk-state {
				scl-pins {
					pins = "gpio57";
					function = "qup2_se0_l1_mira";
					drive-strength = <2>;
					bias-pull-up = <2200>;
				};

				sda-pins {
					pins = "gpio56";
					function = "qup2_se0_l0_mira";
					drive-strength = <2>;
					bias-pull-up = <2200>;
				};
			};

			qup_i2c9_data_clk: qup-i2c9-data-clk-state {
				/* SDA, SCL */
				pins = "gpio60", "gpio61";
				function = "qup2_se1";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c10_data_clk: qup-i2c10-data-clk-state {
				/* SDA, SCL */
				pins = "gpio64", "gpio65";
				function = "qup2_se2";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c11_data_clk: qup-i2c11-data-clk-state {
				/* SDA, SCL */
				pins = "gpio68", "gpio69";
				function = "qup2_se3";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c12_data_clk: qup-i2c12-data-clk-state {
				/* SDA, SCL */
				pins = "gpio2", "gpio3";
				function = "qup2_se4";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c13_data_clk: qup-i2c13-data-clk-state {
				/* SDA, SCL */
				pins = "gpio80", "gpio81";
				function = "qup2_se5";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_i2c15_data_clk: qup-i2c15-data-clk-state {
				/* SDA, SCL */
				pins = "gpio72", "gpio106";
				function = "qup2_se7";
				drive-strength = <2>;
				bias-pull-up = <2200>;
			};

			qup_spi0_cs: qup-spi0-cs-state {
				pins = "gpio31";
				function = "qup1_se0";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi0_data_clk: qup-spi0-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio28", "gpio29", "gpio30";
				function = "qup1_se0";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi1_cs: qup-spi1-cs-state {
				pins = "gpio35";
				function = "qup1_se1";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi1_data_clk: qup-spi1-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio32", "gpio33", "gpio34";
				function = "qup1_se1";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi2_cs: qup-spi2-cs-state {
				pins = "gpio39";
				function = "qup1_se2";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi2_data_clk: qup-spi2-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio36", "gpio37", "gpio38";
				function = "qup1_se2";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi3_cs: qup-spi3-cs-state {
				pins = "gpio43";
				function = "qup1_se3";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi3_data_clk: qup-spi3-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio40", "gpio41", "gpio42";
				function = "qup1_se3";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi4_cs: qup-spi4-cs-state {
				pins = "gpio47";
				function = "qup1_se4";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi4_data_clk: qup-spi4-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio44", "gpio45", "gpio46";
				function = "qup1_se4";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi5_cs: qup-spi5-cs-state {
				pins = "gpio55";
				function = "qup1_se5";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi5_data_clk: qup-spi5-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio52", "gpio53", "gpio54";
				function = "qup1_se5";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi6_cs: qup-spi6-cs-state {
				pins = "gpio51";
				function = "qup1_se6";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi6_data_clk: qup-spi6-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio48", "gpio49", "gpio50";
				function = "qup1_se6";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi8_cs: qup-spi8-cs-state {
				pins = "gpio59";
				function = "qup2_se0_l3_mira";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi8_data_clk: qup-spi8-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio56", "gpio57", "gpio58";
				function = "qup2_se0_l2_mira";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi9_cs: qup-spi9-cs-state {
				pins = "gpio63";
				function = "qup2_se1";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi9_data_clk: qup-spi9-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio60", "gpio61", "gpio62";
				function = "qup2_se1";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi10_cs: qup-spi10-cs-state {
				pins = "gpio67";
				function = "qup2_se2";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi10_data_clk: qup-spi10-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio64", "gpio65", "gpio66";
				function = "qup2_se2";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi11_cs: qup-spi11-cs-state {
				pins = "gpio71";
				function = "qup2_se3";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi11_data_clk: qup-spi11-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio68", "gpio69", "gpio70";
				function = "qup2_se3";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi12_cs: qup-spi12-cs-state {
				pins = "gpio119";
				function = "qup2_se4";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi12_data_clk: qup-spi12-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio2", "gpio3", "gpio118";
				function = "qup2_se4";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi13_cs: qup-spi13-cs-state {
				pins = "gpio83";
				function = "qup2_se5";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi13_data_clk: qup-spi13-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio80", "gpio81", "gpio82";
				function = "qup2_se5";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi15_cs: qup-spi15-cs-state {
				pins = "gpio75";
				function = "qup2_se7";
				drive-strength = <6>;
				bias-disable;
			};

			qup_spi15_data_clk: qup-spi15-data-clk-state {
				/* MISO, MOSI, CLK */
				pins = "gpio72", "gpio106", "gpio74";
				function = "qup2_se7";
				drive-strength = <6>;
				bias-disable;
			};

			qup_uart7_default: qup-uart7-default-state {
				/* TX, RX */
				pins = "gpio26", "gpio27";
				function = "qup1_se7";
				drive-strength = <2>;
				bias-disable;
			};

			qup_uart14_default: qup-uart14-default-state {
				/* TX, RX */
				pins = "gpio78", "gpio79";
				function = "qup2_se6";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_uart14_cts_rts: qup-uart14-cts-rts-state {
				/* CTS, RTS */
				pins = "gpio76", "gpio77";
				function = "qup2_se6";
				drive-strength = <2>;
				bias-pull-down;
			};

			sdc2_sleep: sdc2-sleep-state {
				clk-pins {
					pins = "sdc2_clk";
					bias-disable;
					drive-strength = <2>;
				};

				cmd-pins {
					pins = "sdc2_cmd";
					bias-pull-up;
					drive-strength = <2>;
				};

				data-pins {
					pins = "sdc2_data";
					bias-pull-up;
					drive-strength = <2>;
				};
			};

			sdc2_default: sdc2-default-state {
				clk-pins {
					pins = "sdc2_clk";
					bias-disable;
					drive-strength = <16>;
				};

				cmd-pins {
					pins = "sdc2_cmd";
					bias-pull-up;
					drive-strength = <10>;
				};

				data-pins {
					pins = "sdc2_data";
					bias-pull-up;
					drive-strength = <10>;
				};
			};
		};

		apps_smmu: iommu@15000000 {
			compatible = "qcom,sm8550-smmu-500", "qcom,smmu-500", "arm,mmu-500";
			reg = <0 0x15000000 0 0x100000>;
			#iommu-cells = <2>;
			#global-interrupts = <1>;
			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 706 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 689 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>;
		};

		intc: interrupt-controller@17100000 {
			compatible = "arm,gic-v3";
			reg = <0 0x17100000 0 0x10000>,		/* GICD */
			      <0 0x17180000 0 0x200000>;	/* GICR * 8 */
			ranges;
			#interrupt-cells = <3>;
			interrupt-controller;
			#redistributor-regions = <1>;
			redistributor-stride = <0 0x40000>;
			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
			#address-cells = <2>;
			#size-cells = <2>;

			gic_its: msi-controller@17140000 {
				compatible = "arm,gic-v3-its";
				reg = <0 0x17140000 0 0x20000>;
				msi-controller;
				#msi-cells = <1>;
			};
		};

		timer@17420000 {
			compatible = "arm,armv7-timer-mem";
			reg = <0 0x17420000 0 0x1000>;
			ranges = <0 0 0 0x20000000>;
			#address-cells = <1>;
			#size-cells = <1>;

			frame@17421000 {
				reg = <0x17421000 0x1000>,
				      <0x17422000 0x1000>;
				frame-number = <0>;
				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
			};

			frame@17423000 {
				reg = <0x17423000 0x1000>;
				frame-number = <1>;
				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};

			frame@17425000 {
				reg = <0x17425000 0x1000>;
				frame-number = <2>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};

			frame@17427000 {
				reg = <0x17427000 0x1000>;
				frame-number = <3>;
				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};

			frame@17429000 {
				reg = <0x17429000 0x1000>;
				frame-number = <4>;
				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};

			frame@1742b000 {
				reg = <0x1742b000 0x1000>;
				frame-number = <5>;
				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};

			frame@1742d000 {
				reg = <0x1742d000 0x1000>;
				frame-number = <6>;
				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};
		};

		apps_rsc: rsc@17a00000 {
			label = "apps_rsc";
			compatible = "qcom,rpmh-rsc";
			reg = <0 0x17a00000 0 0x10000>,
			      <0 0x17a10000 0 0x10000>,
			      <0 0x17a20000 0 0x10000>,
			      <0 0x17a30000 0 0x10000>;
			reg-names = "drv-0", "drv-1", "drv-2", "drv-3";
			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
			qcom,tcs-offset = <0xd00>;
			qcom,drv-id = <2>;
			qcom,tcs-config = <ACTIVE_TCS    3>, <SLEEP_TCS     2>,
					  <WAKE_TCS      2>, <CONTROL_TCS   0>;
			power-domains = <&CLUSTER_PD>;

			apps_bcm_voter: bcm-voter {
				compatible = "qcom,bcm-voter";
			};

			rpmhcc: clock-controller {
				compatible = "qcom,sm8550-rpmh-clk";
				#clock-cells = <1>;
				clock-names = "xo";
				clocks = <&xo_board>;
			};

			rpmhpd: power-controller {
				compatible = "qcom,sm8550-rpmhpd";
				#power-domain-cells = <1>;
				operating-points-v2 = <&rpmhpd_opp_table>;

				rpmhpd_opp_table: opp-table {
					compatible = "operating-points-v2";

					rpmhpd_opp_ret: opp-16 {
						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
					};

					rpmhpd_opp_min_svs: opp-48 {
						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
					};

					rpmhpd_opp_low_svs_d2: opp-52 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D2>;
					};

					rpmhpd_opp_low_svs_d1: opp-56 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
					};

					rpmhpd_opp_low_svs_d0: opp-60 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D0>;
					};

					rpmhpd_opp_low_svs: opp-64 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
					};

					rpmhpd_opp_low_svs_l1: opp-80 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_L1>;
					};

					rpmhpd_opp_svs: opp-128 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
					};

					rpmhpd_opp_svs_l0: opp-144 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L0>;
					};

					rpmhpd_opp_svs_l1: opp-192 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
					};

					rpmhpd_opp_nom: opp-256 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
					};

					rpmhpd_opp_nom_l1: opp-320 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
					};

					rpmhpd_opp_nom_l2: opp-336 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
					};

					rpmhpd_opp_turbo: opp-384 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
					};

					rpmhpd_opp_turbo_l1: opp-416 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
					};
				};
			};
		};

		cpufreq_hw: cpufreq@17d91000 {
			compatible = "qcom,sm8550-cpufreq-epss", "qcom,cpufreq-epss";
			reg = <0 0x17d91000 0 0x1000>,
			      <0 0x17d92000 0 0x1000>,
			      <0 0x17d93000 0 0x1000>;
			reg-names = "freq-domain0", "freq-domain1", "freq-domain2";
			clocks = <&bi_tcxo_div2>, <&gcc GCC_GPLL0>;
			clock-names = "xo", "alternate";
			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "dcvsh-irq-0", "dcvsh-irq-1", "dcvsh-irq-2";
			#freq-domain-cells = <1>;
			#clock-cells = <1>;
		};

		pmu@24091000 {
			compatible = "qcom,sm8550-llcc-bwmon", "qcom,sc7280-llcc-bwmon";
			reg = <0 0x24091000 0 0x1000>;
			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
			interconnects = <&mc_virt MASTER_LLCC 3 &mc_virt SLAVE_EBI1 3>;

			operating-points-v2 = <&llcc_bwmon_opp_table>;

			llcc_bwmon_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-0 {
					opp-peak-kBps = <2086000>;
				};

				opp-1 {
					opp-peak-kBps = <2929000>;
				};

				opp-2 {
					opp-peak-kBps = <5931000>;
				};

				opp-3 {
					opp-peak-kBps = <6515000>;
				};

				opp-4 {
					opp-peak-kBps = <7980000>;
				};

				opp-5 {
					opp-peak-kBps = <10437000>;
				};

				opp-6 {
					opp-peak-kBps = <12157000>;
				};

				opp-7 {
					opp-peak-kBps = <14060000>;
				};

				opp-8 {
					opp-peak-kBps = <16113000>;
				};
			};
		};

		pmu@240b6400 {
			compatible = "qcom,sm8550-cpu-bwmon", "qcom,sdm845-bwmon";
			reg = <0 0x240b6400 0 0x600>;
			interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;
			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &gem_noc SLAVE_LLCC 3>;

			operating-points-v2 = <&cpu_bwmon_opp_table>;

			cpu_bwmon_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-0 {
					opp-peak-kBps = <4577000>;
				};

				opp-1 {
					opp-peak-kBps = <7110000>;
				};

				opp-2 {
					opp-peak-kBps = <9155000>;
				};

				opp-3 {
					opp-peak-kBps = <12298000>;
				};

				opp-4 {
					opp-peak-kBps = <14236000>;
				};

				opp-5 {
					opp-peak-kBps = <16265000>;
				};
			};
		};

		gem_noc: interconnect@24100000 {
			compatible = "qcom,sm8550-gem-noc";
			reg = <0 0x24100000 0 0xbb800>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		system-cache-controller@25000000 {
			compatible = "qcom,sm8550-llcc";
			reg = <0 0x25000000 0 0x200000>,
			      <0 0x25200000 0 0x200000>,
			      <0 0x25400000 0 0x200000>,
			      <0 0x25600000 0 0x200000>,
			      <0 0x25800000 0 0x200000>;
			reg-names = "llcc0_base",
				    "llcc1_base",
				    "llcc2_base",
				    "llcc3_base",
				    "llcc_broadcast_base";
			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
		};

		remoteproc_adsp: remoteproc@30000000 {
			compatible = "qcom,sm8550-adsp-pas";
			reg = <0x0 0x30000000 0x0 0x100>;

			interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd RPMHPD_LCX>,
					<&rpmhpd RPMHPD_LMX>;
			power-domain-names = "lcx", "lmx";

			interconnects = <&lpass_lpicx_noc MASTER_LPASS_PROC 0 &mc_virt SLAVE_EBI1 0>;

			memory-region = <&adspslpi_mem>, <&q6_adsp_dtb_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_adsp_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			remoteproc_adsp_glink: glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_LPASS
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "lpass";
				qcom,remote-pid = <2>;

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "adsp";
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@3 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <3>;
						iommus = <&apps_smmu 0x1003 0x80>,
							 <&apps_smmu 0x1063 0x0>;
						dma-coherent;
					};

					compute-cb@4 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <4>;
						iommus = <&apps_smmu 0x1004 0x80>,
							 <&apps_smmu 0x1064 0x0>;
						dma-coherent;
					};

					compute-cb@5 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <5>;
						iommus = <&apps_smmu 0x1005 0x80>,
							 <&apps_smmu 0x1065 0x0>;
						dma-coherent;
					};

					compute-cb@6 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <6>;
						iommus = <&apps_smmu 0x1006 0x80>,
							 <&apps_smmu 0x1066 0x0>;
						dma-coherent;
					};

					compute-cb@7 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <7>;
						iommus = <&apps_smmu 0x1007 0x80>,
							 <&apps_smmu 0x1067 0x0>;
						dma-coherent;
					};
				};

				gpr {
					compatible = "qcom,gpr";
					qcom,glink-channels = "adsp_apps";
					qcom,domain = <GPR_DOMAIN_ID_ADSP>;
					qcom,intents = <512 20>;
					#address-cells = <1>;
					#size-cells = <0>;

					q6apm: service@1 {
						compatible = "qcom,q6apm";
						reg = <GPR_APM_MODULE_IID>;
						#sound-dai-cells = <0>;
						qcom,protection-domain = "avs/audio",
									 "msm/adsp/audio_pd";

						q6apmdai: dais {
							compatible = "qcom,q6apm-dais";
							iommus = <&apps_smmu 0x1001 0x80>,
								 <&apps_smmu 0x1061 0x0>;
						};

						q6apmbedai: bedais {
							compatible = "qcom,q6apm-lpass-dais";
							#sound-dai-cells = <1>;
						};
					};

					q6prm: service@2 {
						compatible = "qcom,q6prm";
						reg = <GPR_PRM_MODULE_IID>;
						qcom,protection-domain = "avs/audio",
									 "msm/adsp/audio_pd";

						q6prmcc: clock-controller {
							compatible = "qcom,q6prm-lpass-clocks";
							#clock-cells = <2>;
						};
					};
				};
			};
		};

		nsp_noc: interconnect@320c0000 {
			compatible = "qcom,sm8550-nsp-noc";
			reg = <0 0x320c0000 0 0xe080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		remoteproc_cdsp: remoteproc@32300000 {
			compatible = "qcom,sm8550-cdsp-pas";
			reg = <0x0 0x32300000 0x0 0x1400000>;

			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd RPMHPD_CX>,
					<&rpmhpd RPMHPD_MXC>,
					<&rpmhpd RPMHPD_NSP>;
			power-domain-names = "cx", "mxc", "nsp";

			interconnects = <&nsp_noc MASTER_CDSP_PROC 0 &mc_virt SLAVE_EBI1 0>;

			memory-region = <&cdsp_mem>, <&q6_cdsp_dtb_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_cdsp_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_CDSP
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "cdsp";
				qcom,remote-pid = <5>;

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "cdsp";
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@1 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <1>;
						iommus = <&apps_smmu 0x1961 0x0>,
							 <&apps_smmu 0x0c01 0x20>,
							 <&apps_smmu 0x19c1 0x10>;
						dma-coherent;
					};

					compute-cb@2 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <2>;
						iommus = <&apps_smmu 0x1962 0x0>,
							 <&apps_smmu 0x0c02 0x20>,
							 <&apps_smmu 0x19c2 0x10>;
						dma-coherent;
					};

					compute-cb@3 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <3>;
						iommus = <&apps_smmu 0x1963 0x0>,
							 <&apps_smmu 0x0c03 0x20>,
							 <&apps_smmu 0x19c3 0x10>;
						dma-coherent;
					};

					compute-cb@4 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <4>;
						iommus = <&apps_smmu 0x1964 0x0>,
							 <&apps_smmu 0x0c04 0x20>,
							 <&apps_smmu 0x19c4 0x10>;
						dma-coherent;
					};

					compute-cb@5 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <5>;
						iommus = <&apps_smmu 0x1965 0x0>,
							 <&apps_smmu 0x0c05 0x20>,
							 <&apps_smmu 0x19c5 0x10>;
						dma-coherent;
					};

					compute-cb@6 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <6>;
						iommus = <&apps_smmu 0x1966 0x0>,
							 <&apps_smmu 0x0c06 0x20>,
							 <&apps_smmu 0x19c6 0x10>;
						dma-coherent;
					};

					compute-cb@7 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <7>;
						iommus = <&apps_smmu 0x1967 0x0>,
							 <&apps_smmu 0x0c07 0x20>,
							 <&apps_smmu 0x19c7 0x10>;
						dma-coherent;
					};

					compute-cb@8 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <8>;
						iommus = <&apps_smmu 0x1968 0x0>,
							 <&apps_smmu 0x0c08 0x20>,
							 <&apps_smmu 0x19c8 0x10>;
						dma-coherent;
					};

					/* note: secure cb9 in downstream */
				};
			};
		};
	};

	thermal-zones {
		aoss0-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 0>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		cpuss0-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 1>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		cpuss1-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 2>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		cpuss2-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 3>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		cpuss3-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 4>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		cpu3-top-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 5>;

			trips {
				cpu3_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_top_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu3-bottom-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 6>;

			trips {
				cpu3_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_bottom_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu4-top-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 7>;

			trips {
				cpu4_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_top_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu4-bottom-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 8>;

			trips {
				cpu4_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_bottom_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu5-top-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 9>;

			trips {
				cpu5_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_top_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu5-bottom-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 10>;

			trips {
				cpu5_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_bottom_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu6-top-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 11>;

			trips {
				cpu6_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_top_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu6-bottom-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 12>;

			trips {
				cpu6_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_bottom_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu7-top-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 13>;

			trips {
				cpu7_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_top_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu7-middle-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 14>;

			trips {
				cpu7_middle_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_middle_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_middle_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu7-bottom-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens0 15>;

			trips {
				cpu7_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_bottom_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		aoss1-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 0>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		cpu0-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 1>;

			trips {
				cpu0_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu0_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu0_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu1-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 2>;

			trips {
				cpu1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu1_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu1_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu2-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 3>;

			trips {
				cpu2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu2_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu2_crit: cpu-critical {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cdsp0-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 4>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				cdsp0_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		cdsp1-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 5>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				cdsp1_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		cdsp2-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 6>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				cdsp2_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		cdsp3-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 7>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				cdsp3_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		video-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 8>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		mem-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 9>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				ddr_config0: ddr0-config {
					temperature = <90000>;
					hysteresis = <5000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		modem0-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 10>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				mdmss0_config0: mdmss0-config0 {
					temperature = <102000>;
					hysteresis = <3000>;
					type = "passive";
				};

				mdmss0_config1: mdmss0-config1 {
					temperature = <105000>;
					hysteresis = <3000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		modem1-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 11>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				mdmss1_config0: mdmss1-config0 {
					temperature = <102000>;
					hysteresis = <3000>;
					type = "passive";
				};

				mdmss1_config1: mdmss1-config1 {
					temperature = <105000>;
					hysteresis = <3000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		modem2-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 12>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				mdmss2_config0: mdmss2-config0 {
					temperature = <102000>;
					hysteresis = <3000>;
					type = "passive";
				};

				mdmss2_config1: mdmss2-config1 {
					temperature = <105000>;
					hysteresis = <3000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		modem3-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 13>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				mdmss3_config0: mdmss3-config0 {
					temperature = <102000>;
					hysteresis = <3000>;
					type = "passive";
				};

				mdmss3_config1: mdmss3-config1 {
					temperature = <105000>;
					hysteresis = <3000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		camera0-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 14>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		camera1-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens1 15>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		aoss2-thermal {
			polling-delay-passive = <0>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 0>;

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		gpuss-0-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 1>;

			cooling-maps {
				map0 {
					trip = <&gpu0_junction_config>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				gpu0_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		gpuss-1-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 2>;

			cooling-maps {
				map0 {
					trip = <&gpu1_junction_config>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				gpu1_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		gpuss-2-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 3>;

			cooling-maps {
				map0 {
					trip = <&gpu2_junction_config>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				gpu2_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		gpuss-3-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 4>;

			cooling-maps {
				map0 {
					trip = <&gpu3_junction_config>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				gpu3_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		gpuss-4-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 5>;

			cooling-maps {
				map0 {
					trip = <&gpu4_junction_config>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				gpu4_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		gpuss-5-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 6>;

			cooling-maps {
				map0 {
					trip = <&gpu5_junction_config>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				gpu5_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		gpuss-6-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 7>;

			cooling-maps {
				map0 {
					trip = <&gpu6_junction_config>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				gpu6_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};

		gpuss-7-thermal {
			polling-delay-passive = <10>;
			polling-delay = <0>;
			thermal-sensors = <&tsens2 8>;

			cooling-maps {
				map0 {
					trip = <&gpu7_junction_config>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};

			trips {
				thermal-engine-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				thermal-hal-config {
					temperature = <125000>;
					hysteresis = <1000>;
					type = "passive";
				};

				reset-mon-config {
					temperature = <115000>;
					hysteresis = <5000>;
					type = "passive";
				};

				gpu7_junction_config: junction-config {
					temperature = <95000>;
					hysteresis = <5000>;
					type = "passive";
				};
			};
		};
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
	};
};