// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Copyright 2018-2019, 2021 NXP
 *
 */

#include <common.h>
#include <command.h>
#include <cpu_func.h>
#include <hang.h>
#include <image.h>
#include <init.h>
#include <log.h>
#include <spl.h>
#include <asm/global_data.h>
#include <asm/io.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx8mn_pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/arch/ddr.h>

#include <dm/uclass.h>
#include <dm/device.h>
#include <dm/uclass-internal.h>
#include <dm/device-internal.h>
#include <power/pmic.h>
#include <power/pca9450.h>
#include <asm/mach-imx/gpio.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <fsl_esdhc_imx.h>
#include <mmc.h>

DECLARE_GLOBAL_DATA_PTR;

int spl_board_boot_device(enum boot_device boot_dev_spl)
{
	return BOOT_DEVICE_BOOTROM;
}

void spl_dram_init(void)
{
	ddr_init(&dram_timing);
}

void spl_board_init(void)
{
	struct udevice *dev;
	int ret;

	arch_misc_init();

	puts("Normal Boot\n");

	ret = uclass_get_device_by_name(UCLASS_CLK,
					"clock-controller@30380000",
					&dev);
	if (ret < 0)
		printf("Failed to find clock node. Check device tree\n");
}

#if CONFIG_IS_ENABLED(DM_PMIC_PCA9450)
int power_init_board(void)
{
	struct udevice *dev;
	int ret;

	ret = pmic_get("pmic@25", &dev);
	if (ret == -ENODEV) {
		puts("No pca9450@25\n");
		return 0;
	}
	if (ret != 0)
		return ret;

	/* BUCKxOUT_DVS0/1 control BUCK123 output */
	pmic_reg_write(dev, PCA9450_BUCK123_DVS, 0x29);

#ifdef CONFIG_IMX8MN_LOW_DRIVE_MODE
	/* Set VDD_SOC/VDD_DRAM to 0.8v for low drive mode */
	pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x10);
#else
	/* increase VDD_SOC/VDD_DRAM to typical value 0.95V before first DRAM access */
	pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x1C);
#endif
	/* Set DVS1 to 0.85v for suspend */
	/* Enable DVS control through PMIC_STBY_REQ and set B1_ENMODE=1 (ON by PMIC_ON_REQ=H) */
	pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x14);
	pmic_reg_write(dev, PCA9450_BUCK1CTRL, 0x59);

	/* set VDD_SNVS_0V8 from default 0.85V */
	pmic_reg_write(dev, PCA9450_LDO2CTRL, 0xC0);

	/* enable LDO4 to 1.2v */
	pmic_reg_write(dev, PCA9450_LDO4CTRL, 0x44);

	/* set WDOG_B_CFG to cold reset */
	pmic_reg_write(dev, PCA9450_RESET_CTRL, 0xA1);

	return 0;
}
#endif

#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
	/* Just empty function now - can't decide what to choose */
	debug("%s: %s\n", __func__, name);

	return 0;
}
#endif

void board_init_f(ulong dummy)
{
	int ret;

	arch_cpu_init();

	init_uart_clk(1);

	timer_init();

	/* Clear the BSS. */
	memset(__bss_start, 0, __bss_end - __bss_start);

	ret = spl_init();
	if (ret) {
		debug("spl_init() failed: %d\n", ret);
		hang();
	}

	preloader_console_init();

	enable_tzc380();

	/* DDR initialization */
	spl_dram_init();

	board_init_r(NULL, 0);
}