/*
 * AU1X00 UART support
 *
 * Hardcoded to UART 0 for now
 * Speed and options also hardcoded to 115200 8N1
 *
 *  Copyright (c) 2003	Thomas.Lange@corelatus.se
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

#include <config.h>

#ifdef CONFIG_AU1X00

#include <common.h>
#include <asm/au1x00.h>

/******************************************************************************
*
* serial_init - initialize a channel
*
* This routine initializes the number of data bits, parity
* and set the selected baud rate. Interrupts are disabled.
* Set the modem control signals if the option is selected.
*
* RETURNS: N/A
*/

int serial_init (void)
{
	volatile u32 *uart_fifoctl = (volatile u32*)(UART0_ADDR+UART_FCR);
	volatile u32 *uart_enable = (volatile u32*)(UART0_ADDR+UART_ENABLE);

	/* Enable clocks first */
	*uart_enable = UART_EN_CE;

	/* Then release reset */
	/* Must release reset before setting other regs */
	*uart_enable = UART_EN_CE|UART_EN_E;

	/* Activate fifos, reset tx and rx */
	/* Set tx trigger level to 12 */
	*uart_fifoctl = UART_FCR_ENABLE_FIFO|UART_FCR_CLEAR_RCVR|
		UART_FCR_CLEAR_XMIT|UART_FCR_T_TRIGGER_12;

	serial_setbrg();

	return 0;
}


void serial_setbrg (void)
{
	volatile u32 *uart_clk = (volatile u32*)(UART0_ADDR+UART_CLK);
	volatile u32 *uart_lcr = (volatile u32*)(UART0_ADDR+UART_LCR);

	/* Set baudrate - FIXME for bus speeds != CPU/2 */
	*uart_clk = ((CFG_HZ/(CONFIG_BAUDRATE * 64)));

	/* Set parity, stop bits and word length to 8N1 */
	*uart_lcr = UART_LCR_WLEN8;
}

void serial_putc (const char c)
{
	volatile u32 *uart_lsr = (volatile u32*)(UART0_ADDR+UART_LSR);
	volatile u32 *uart_tx = (volatile u32*)(UART0_ADDR+UART_TX);

	if (c == '\n') serial_putc ('\r');

	/* Wait for fifo to shift out some bytes */
	while((*uart_lsr&UART_LSR_THRE)==0);

	*uart_tx = (u32)c;
}

void serial_puts (const char *s)
{
	while (*s)
	{
		serial_putc (*s++);
	}
}

int serial_getc (void)
{
	volatile u32 *uart_rx = (volatile u32*)(UART0_ADDR+UART_RX);
	char c;

	while (!serial_tstc());

	c = (*uart_rx&0xFF);
	return c;
}

int serial_tstc (void)
{
	volatile u32 *uart_lsr = (volatile u32*)(UART0_ADDR+UART_LSR);

	if(*uart_lsr&UART_LSR_DR){
		/* Data in rfifo */
		return(1);
	}
	return 0;
}
#endif /* CONFIG_SERIAL_AU1X00 */