/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2018 NXP
 */

#ifndef __IMX8M_PICOPI_H
#define __IMX8M_PICOPI_H

#include <linux/sizes.h>
#include <asm/arch/imx-regs.h>

#define CONFIG_SPL_MAX_SIZE		(124 * 1024)
#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300

#ifdef CONFIG_SPL_BUILD
/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
#define CONFIG_SPL_WATCHDOG
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
#define CONFIG_SPL_POWER
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_STACK		0x187FF0
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_GPIO
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_BSS_START_ADDR	0x00180000
#define CONFIG_SPL_BSS_MAX_SIZE		0x2000	/* 8 KB */
#define CONFIG_SYS_SPL_MALLOC_START	0x42200000
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x80000	/* 512 KB */
#define CONFIG_SYS_SPL_PTE_RAM_BASE	0x41580000

/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
#define CONFIG_MALLOC_F_ADDR		0x182000
/* For RAW image gives a error info not panic */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE

#undef CONFIG_DM_MMC
#undef CONFIG_DM_PMIC

#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */

#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

#define CONFIG_POWER
#define CONFIG_POWER_I2C
#endif

#define CONFIG_REMAKE_ELF

/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
#define CONFIG_MII
#define CONFIG_ETHPRIME			"FEC"

#define CONFIG_FEC_MXC
#define CONFIG_FEC_XCV_TYPE		RGMII
#define CONFIG_FEC_MXC_PHYADDR		1
#define FEC_QUIRK_ENET_MAC

#define CONFIG_PHY_GIGE
#define IMX_FEC_BASE			0x30BE0000

#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
#endif

/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS					\
	"script=boot.scr\0"						\
	"image=Image\0"							\
	"console=ttymxc0,115200\0"					\
	"fdt_addr=0x43000000\0"						\
	"fdt_high=0xffffffffffffffff\0"					\
	"fdt_file=imx8mq-pico-pi.dtb\0"					\
	"initrd_addr=0x43800000\0"					\
	"initrd_high=0xffffffffffffffff\0"				\
	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0"		\
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0"	\
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0"			\
	"mmcautodetect=yes\0"						\
	"mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 "	\
	"loadbootscript="						\
		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; source\0"	\
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; "				\
		"run mmcargs; "						\
		"echo wait for boot; "					\
		"fi;\0"							\
	"netargs=setenv bootargs console=${console} "			\
		"root=/dev/nfs "					\
		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0"	\
	"netboot=echo Booting from net ...; "				\
		"run netargs;  "					\
		"if test ${ip_dyn} = yes; then "			\
			"setenv get_cmd dhcp; "				\
		"else "							\
			"setenv get_cmd tftp; "				\
		"fi; "							\
		"${get_cmd} ${loadaddr} ${image}; "			\
		"booti; "

#define CONFIG_BOOTCOMMAND \
	"mmc dev ${mmcdev}; if mmc rescan; then "			\
		"if run loadbootscript; then "				\
			"run bootscript; "				\
		"else "							\
			"if run loadimage; then "			\
				"run mmcboot; "				\
			"else run netboot; "				\
			"fi; "						\
		"fi; "							\
	"else booti ${loadaddr} - ${fdt_addr}; fi"

/* Link Definitions */
#define CONFIG_LOADADDR			0x40480000

#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR

#define CONFIG_SYS_INIT_RAM_ADDR	0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE	0x80000
#define CONFIG_SYS_INIT_SP_OFFSET	\
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR		\
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

#define CONFIG_MMCROOT			"/dev/mmcblk1p2"	/* USDHC2 */

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)

#define CONFIG_SYS_SDRAM_BASE		0x40000000
#define PHYS_SDRAM			0x40000000
#define PHYS_SDRAM_SIZE			0x80000000	/* 2 GiB DDR */

#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM
#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + \
					(PHYS_SDRAM_SIZE >> 1))

#define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR

/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE		1024
#define CONFIG_SYS_MAXARGS		64
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)

#define CONFIG_IMX_BOOTAUX

#define CONFIG_SYS_FSL_USDHC_NUM	2
#define CONFIG_SYS_FSL_ESDHC_ADDR	0

#define CONFIG_SYS_MMC_IMG_LOAD_PART	1

#define CONFIG_MXC_GPIO

/* I2C Configs */
#define CONFIG_SYS_I2C_SPEED		100000

#define CONFIG_OF_SYSTEM_SETUP

#ifndef CONFIG_SPL_BUILD
#define CONFIG_DM_PMIC
#endif

#define CONFIG_SYS_BOOTM_LEN		SZ_128M

#endif