/* SPDX-License-Identifier: GPL-2.0 */
/*
 * Copyright (c) 2016-2018, 2020, The Linux Foundation. All rights reserved.
 * Copyright (c) 2023, Linaro Ltd.
 */

#include <common.h>
#include <linux/err.h>
#include <linux/types.h>
#include <dm.h>
#include <dm/ofnode.h>
#include <dm/devres.h>
#include <dm/device_compat.h>
#include <linux/delay.h>
#include <dm/lists.h>
#include <errno.h>
#include <asm/io.h>
#include <asm/bitops.h>
#include <linux/bitmap.h>
#include <log.h>

#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include "rpmh-internal.h"

#include <soc/qcom/rpmh.h>
#include <soc/qcom/cmd-db.h>

#define RSC_DRV_ID			0

#define MAJOR_VER_MASK			0xFF
#define MAJOR_VER_SHIFT			16
#define MINOR_VER_MASK			0xFF
#define MINOR_VER_SHIFT			8

enum {
	RSC_DRV_TCS_OFFSET,
	RSC_DRV_CMD_OFFSET,
	DRV_SOLVER_CONFIG,
	DRV_PRNT_CHLD_CONFIG,
	RSC_DRV_IRQ_ENABLE,
	RSC_DRV_IRQ_STATUS,
	RSC_DRV_IRQ_CLEAR,
	RSC_DRV_CMD_WAIT_FOR_CMPL,
	RSC_DRV_CONTROL,
	RSC_DRV_STATUS,
	RSC_DRV_CMD_ENABLE,
	RSC_DRV_CMD_MSGID,
	RSC_DRV_CMD_ADDR,
	RSC_DRV_CMD_DATA,
	RSC_DRV_CMD_STATUS,
	RSC_DRV_CMD_RESP_DATA,
};

/* DRV HW Solver Configuration Information Register */
#define DRV_HW_SOLVER_MASK		1
#define DRV_HW_SOLVER_SHIFT		24

/* DRV TCS Configuration Information Register */
#define DRV_NUM_TCS_MASK		0x3F
#define DRV_NUM_TCS_SHIFT		6
#define DRV_NCPT_MASK			0x1F
#define DRV_NCPT_SHIFT			27

/* Offsets for CONTROL TCS Registers */
#define RSC_DRV_CTL_TCS_DATA_HI		0x38
#define RSC_DRV_CTL_TCS_DATA_HI_MASK	0xFFFFFF
#define RSC_DRV_CTL_TCS_DATA_HI_VALID	BIT(31)
#define RSC_DRV_CTL_TCS_DATA_LO		0x40
#define RSC_DRV_CTL_TCS_DATA_LO_MASK	0xFFFFFFFF
#define RSC_DRV_CTL_TCS_DATA_SIZE	32

#define TCS_AMC_MODE_ENABLE		BIT(16)
#define TCS_AMC_MODE_TRIGGER		BIT(24)

/* TCS CMD register bit mask */
#define CMD_MSGID_LEN			8
#define CMD_MSGID_RESP_REQ		BIT(8)
#define CMD_MSGID_WRITE			BIT(16)
#define CMD_STATUS_ISSUED		BIT(8)
#define CMD_STATUS_COMPL		BIT(16)

/*
 * Here's a high level overview of how all the registers in RPMH work
 * together:
 *
 * - The main rpmh-rsc address is the base of a register space that can
 *   be used to find overall configuration of the hardware
 *   (DRV_PRNT_CHLD_CONFIG). Also found within the rpmh-rsc register
 *   space are all the TCS blocks. The offset of the TCS blocks is
 *   specified in the device tree by "qcom,tcs-offset" and used to
 *   compute tcs_base.
 * - TCS blocks come one after another. Type, count, and order are
 *   specified by the device tree as "qcom,tcs-config".
 * - Each TCS block has some registers, then space for up to 16 commands.
 *   Note that though address space is reserved for 16 commands, fewer
 *   might be present. See ncpt (num cmds per TCS).
 *
 * Here's a picture:
 *
 *  +---------------------------------------------------+
 *  |RSC                                                |
 *  | ctrl                                              |
 *  |                                                   |
 *  | Drvs:                                             |
 *  | +-----------------------------------------------+ |
 *  | |DRV0                                           | |
 *  | | ctrl/config                                   | |
 *  | | IRQ                                           | |
 *  | |                                               | |
 *  | | TCSes:                                        | |
 *  | | +------------------------------------------+  | |
 *  | | |TCS0  |  |  |  |  |  |  |  |  |  |  |  |  |  | |
 *  | | | ctrl | 0| 1| 2| 3| 4| 5| .| .| .| .|14|15|  | |
 *  | | |      |  |  |  |  |  |  |  |  |  |  |  |  |  | |
 *  | | +------------------------------------------+  | |
 *  | | +------------------------------------------+  | |
 *  | | |TCS1  |  |  |  |  |  |  |  |  |  |  |  |  |  | |
 *  | | | ctrl | 0| 1| 2| 3| 4| 5| .| .| .| .|14|15|  | |
 *  | | |      |  |  |  |  |  |  |  |  |  |  |  |  |  | |
 *  | | +------------------------------------------+  | |
 *  | | +------------------------------------------+  | |
 *  | | |TCS2  |  |  |  |  |  |  |  |  |  |  |  |  |  | |
 *  | | | ctrl | 0| 1| 2| 3| 4| 5| .| .| .| .|14|15|  | |
 *  | | |      |  |  |  |  |  |  |  |  |  |  |  |  |  | |
 *  | | +------------------------------------------+  | |
 *  | |                    ......                     | |
 *  | +-----------------------------------------------+ |
 *  | +-----------------------------------------------+ |
 *  | |DRV1                                           | |
 *  | | (same as DRV0)                                | |
 *  | +-----------------------------------------------+ |
 *  |                      ......                       |
 *  +---------------------------------------------------+
 */

static u32 rpmh_rsc_reg_offset_ver_2_7[] = {
	[RSC_DRV_TCS_OFFSET]		= 672,
	[RSC_DRV_CMD_OFFSET]		= 20,
	[DRV_SOLVER_CONFIG]		= 0x04,
	[DRV_PRNT_CHLD_CONFIG]		= 0x0C,
	[RSC_DRV_IRQ_ENABLE]		= 0x00,
	[RSC_DRV_IRQ_STATUS]		= 0x04,
	[RSC_DRV_IRQ_CLEAR]		= 0x08,
	[RSC_DRV_CMD_WAIT_FOR_CMPL]	= 0x10,
	[RSC_DRV_CONTROL]		= 0x14,
	[RSC_DRV_STATUS]		= 0x18,
	[RSC_DRV_CMD_ENABLE]		= 0x1C,
	[RSC_DRV_CMD_MSGID]		= 0x30,
	[RSC_DRV_CMD_ADDR]		= 0x34,
	[RSC_DRV_CMD_DATA]		= 0x38,
	[RSC_DRV_CMD_STATUS]		= 0x3C,
	[RSC_DRV_CMD_RESP_DATA]		= 0x40,
};


static inline void __iomem *
tcs_reg_addr(const struct rsc_drv *drv, int reg, int tcs_id)
{
	return drv->tcs_base + drv->regs[RSC_DRV_TCS_OFFSET] * tcs_id + reg;
}

static inline void __iomem *
tcs_cmd_addr(const struct rsc_drv *drv, int reg, int tcs_id, int cmd_id)
{
	return tcs_reg_addr(drv, reg, tcs_id) + drv->regs[RSC_DRV_CMD_OFFSET] * cmd_id;
}

static u32 read_tcs_reg(const struct rsc_drv *drv, int reg, int tcs_id)
{
	return readl_relaxed(tcs_reg_addr(drv, reg, tcs_id));
}

static void write_tcs_cmd(const struct rsc_drv *drv, int reg, int tcs_id,
			  int cmd_id, u32 data)
{
	void __iomem *addr = tcs_cmd_addr(drv, reg, tcs_id, cmd_id);
	debug("%s: tcs(m): %d cmd(n): %d addr: %#x data: %#x\n", drv->name,
	       tcs_id, cmd_id, reg, data);
	writel_relaxed(data, addr);
}

static void write_tcs_reg(const struct rsc_drv *drv, int reg, int tcs_id,
			  u32 data)
{
	void __iomem *addr = tcs_reg_addr(drv, reg, tcs_id);
	debug("%s: tcs(m): %d addr: %#x data: %#x\n", drv->name,
	       tcs_id, reg, data);
	writel_relaxed(data, addr);
}

static void write_tcs_reg_sync(const struct rsc_drv *drv, int reg, int tcs_id,
			       u32 data)
{
	int i;
	void __iomem *addr = tcs_reg_addr(drv, reg, tcs_id);

	debug("%s: tcs(m): %d addr: %#x data: %#x\n", drv->name,
	       tcs_id, reg, data);

	writel(data, addr);

	/*
	 * Wait until we read back the same value.  Use a counter rather than
	 * ktime for timeout since this may be called after timekeeping stops.
	 */
	for (i = 0; i < USEC_PER_SEC; i++) {
		if (readl(addr) == data)
			return;
		udelay(1);
	}
	pr_err("%s: error writing %#x to %d:%#x\n", drv->name,
	       data, tcs_id, reg);
}

/**
 * tcs_invalidate() - Invalidate all TCSes of the given type (sleep or wake).
 * @drv:  The RSC controller.
 * @type: SLEEP_TCS or WAKE_TCS
 *
 * This will clear the "slots" variable of the given tcs_group and also
 * tell the hardware to forget about all entries.
 *
 * The caller must ensure that no other RPMH actions are happening when this
 * function is called, since otherwise the device may immediately become
 * used again even before this function exits.
 */
static void tcs_invalidate(struct rsc_drv *drv, int type)
{
	int m;
	struct tcs_group *tcs = &drv->tcs[type];

	/* Caller ensures nobody else is running so no lock */
	if (bitmap_empty(tcs->slots, MAX_TCS_SLOTS))
		return;

	for (m = tcs->offset; m < tcs->offset + tcs->num_tcs; m++)
		write_tcs_reg_sync(drv, drv->regs[RSC_DRV_CMD_ENABLE], m, 0);

	bitmap_zero(tcs->slots, MAX_TCS_SLOTS);
}

/**
 * rpmh_rsc_invalidate() - Invalidate sleep and wake TCSes.
 * @drv: The RSC controller.
 *
 * The caller must ensure that no other RPMH actions are happening when this
 * function is called, since otherwise the device may immediately become
 * used again even before this function exits.
 */
void rpmh_rsc_invalidate(struct rsc_drv *drv)
{
	tcs_invalidate(drv, SLEEP_TCS);
	tcs_invalidate(drv, WAKE_TCS);
}

/**
 * rpmh_rsc_wait_for_resp() - Spin until we get a response from the rpmh
 * @drv:    The controller.
 * @tcs_id: The global ID of this TCS.
 *
 * This is for ACTIVE_ONLY transfers (which are the only ones we support in
 * u-boot). As we don't support interrupts, we just spin on the IRQ_STATUS
 * register until the bit is set to confirm that the TCS TX is done.
 */
int rpmh_rsc_wait_for_resp(struct rsc_drv *drv, int tcs_id)
{
	u32 reg;
	int i;

	reg = drv->regs[RSC_DRV_IRQ_STATUS];

	debug("%s: waiting for response on tcs %d\n", __func__, tcs_id);

	for (i = 0; i < 5 * USEC_PER_SEC; i++) {
		if (readl(tcs_reg_addr(drv, reg, tcs_id)) & BIT(tcs_id))
			break;
		udelay(1);
	}

	if (i == 5 * USEC_PER_SEC) {
		printf("%s: timeout waiting for response\n", drv->name);
		return -ETIMEDOUT;
	}

	writel_relaxed(BIT(tcs_id), drv->tcs_base + drv->regs[RSC_DRV_IRQ_CLEAR]);

	return 0;
}

/**
 * __tcs_buffer_write() - Write to TCS hardware from a request; don't trigger.
 * @drv:    The controller.
 * @tcs_id: The global ID of this TCS.
 * @cmd_id: The index within the TCS to start writing.
 * @msg:    The message we want to send, which will contain several addr/data
 *          pairs to program (but few enough that they all fit in one TCS).
 *
 * This is used for all types of transfers (active, sleep, and wake).
 */
static void __tcs_buffer_write(struct rsc_drv *drv, int tcs_id, int cmd_id,
			       const struct tcs_request *msg)
{
	u32 msgid;
	u32 cmd_msgid = CMD_MSGID_LEN | CMD_MSGID_WRITE;
	u32 cmd_enable = 0;
	struct tcs_cmd *cmd;
	int i, j;

	/* u-boot: get a response to ensure everything is golden before continuing */
	cmd_msgid |= CMD_MSGID_RESP_REQ;

	for (i = 0, j = cmd_id; i < msg->num_cmds; i++, j++) {
		cmd = &msg->cmds[i];
		cmd_enable |= BIT(j);
		msgid = cmd_msgid;
		/*
		 * Additionally, if the cmd->wait is set, make the command
		 * response reqd even if the overall request was fire-n-forget.
		 */
		msgid |= cmd->wait ? CMD_MSGID_RESP_REQ : 0;

		write_tcs_cmd(drv, drv->regs[RSC_DRV_CMD_MSGID], tcs_id, j, msgid);
		write_tcs_cmd(drv, drv->regs[RSC_DRV_CMD_ADDR], tcs_id, j, cmd->addr);
		write_tcs_cmd(drv, drv->regs[RSC_DRV_CMD_DATA], tcs_id, j, cmd->data);
		debug("%s: tcs(m): %d [%s] cmd(n): %d msgid: %#x addr: %#x data: %#x complete: %d\n",
			drv->name, tcs_id, msg->state == RPMH_ACTIVE_ONLY_STATE ? "active" : "?", j, msgid,
			cmd->addr, cmd->data, cmd->wait);
	}

	cmd_enable |= read_tcs_reg(drv, drv->regs[RSC_DRV_CMD_ENABLE], tcs_id);
	write_tcs_reg(drv, drv->regs[RSC_DRV_CMD_ENABLE], tcs_id, cmd_enable);
}


/**
 * __tcs_set_trigger() - Start xfer on a TCS or unset trigger on a borrowed TCS
 * @drv:     The controller.
 * @tcs_id:  The global ID of this TCS.
 * @trigger: If true then untrigger/retrigger. If false then just untrigger.
 *
 * In the normal case we only ever call with "trigger=true" to start a
 * transfer. That will un-trigger/disable the TCS from the last transfer
 * then trigger/enable for this transfer.
 *
 * If we borrowed a wake TCS for an active-only transfer we'll also call
 * this function with "trigger=false" to just do the un-trigger/disable
 * before using the TCS for wake purposes again.
 *
 * Note that the AP is only in charge of triggering active-only transfers.
 * The AP never triggers sleep/wake values using this function.
 */
static void __tcs_set_trigger(struct rsc_drv *drv, int tcs_id, bool trigger)
{
	u32 enable;
	u32 reg = drv->regs[RSC_DRV_CONTROL];

	/*
	 * HW req: Clear the DRV_CONTROL and enable TCS again
	 * While clearing ensure that the AMC mode trigger is cleared
	 * and then the mode enable is cleared.
	 */
	enable = read_tcs_reg(drv, reg, tcs_id);
	enable &= ~TCS_AMC_MODE_TRIGGER;
	write_tcs_reg_sync(drv, reg, tcs_id, enable);
	enable &= ~TCS_AMC_MODE_ENABLE;
	write_tcs_reg_sync(drv, reg, tcs_id, enable);

	if (trigger) {
		/* Enable the AMC mode on the TCS and then trigger the TCS */
		enable = TCS_AMC_MODE_ENABLE;
		write_tcs_reg_sync(drv, reg, tcs_id, enable);
		enable |= TCS_AMC_MODE_TRIGGER;
		write_tcs_reg(drv, reg, tcs_id, enable);
	}
}

/**
 * get_tcs_for_msg() - Get the tcs_group used to send the given message.
 * @drv: The RSC controller.
 * @msg: The message we want to send.
 *
 * This is normally pretty straightforward except if we are trying to send
 * an ACTIVE_ONLY message but don't have any active_only TCSes.
 *
 * Return: A pointer to a tcs_group or an ERR_PTR.
 */
static struct tcs_group *get_tcs_for_msg(struct rsc_drv *drv,
					 const struct tcs_request *msg)
{
	if (msg->state != RPMH_ACTIVE_ONLY_STATE) {
		printf("WARN: only ACTIVE_ONLY state supported\n");
		return ERR_PTR(-EINVAL);
	}

	return &drv->tcs[ACTIVE_TCS];
}

/**
 * rpmh_rsc_send_data() - Write / trigger active-only message.
 * @drv: The controller.
 * @msg: The data to be sent.
 *
 * NOTES:
 * - This is only used for "ACTIVE_ONLY" since the limitations of this
 *   function don't make sense for sleep/wake cases.
 * - To do the transfer, we will grab a whole TCS for ourselves--we don't
 *   try to share. If there are none available we'll wait indefinitely
 *   for a free one.
 * - This function will not wait for the commands to be finished, only for
 *   data to be programmed into the RPMh. See rpmh_tx_done() which will
 *   be called when the transfer is fully complete.
 * - This function must be called with interrupts enabled. If the hardware
 *   is busy doing someone else's transfer we need that transfer to fully
 *   finish so that we can have the hardware, and to fully finish it needs
 *   the interrupt handler to run. If the interrupts is set to run on the
 *   active CPU this can never happen if interrupts are disabled.
 *
 * Return: 0 on success, -EINVAL on error.
 */
int rpmh_rsc_send_data(struct rsc_drv *drv, const struct tcs_request *msg)
{
	struct tcs_group *tcs;
	int tcs_id;
	unsigned long flags;

	tcs = get_tcs_for_msg(drv, msg);
	if (IS_ERR(tcs))
		return PTR_ERR(tcs);

	spin_lock_irqsave(&drv->lock, flags);

	/* u-boot is single-threaded, always use the first TCS as we'll never conflict */
	tcs_id = tcs->offset;

	tcs->req[tcs_id - tcs->offset] = msg;
	generic_set_bit(tcs_id, drv->tcs_in_use);
	if (msg->state == RPMH_ACTIVE_ONLY_STATE && tcs->type != ACTIVE_TCS) {
		/*
		 * Clear previously programmed WAKE commands in selected
		 * repurposed TCS to avoid triggering them. tcs->slots will be
		 * cleaned from rpmh_flush() by invoking rpmh_rsc_invalidate()
		 */
		write_tcs_reg_sync(drv, drv->regs[RSC_DRV_CMD_ENABLE], tcs_id, 0);
		//enable_tcs_irq(drv, tcs_id, true);
	}
	spin_unlock_irqrestore(&drv->lock, flags);

	/*
	 * These two can be done after the lock is released because:
	 * - We marked "tcs_in_use" under lock.
	 * - Once "tcs_in_use" has been marked nobody else could be writing
	 *   to these registers until the interrupt goes off.
	 * - The interrupt can't go off until we trigger w/ the last line
	 *   of __tcs_set_trigger() below.
	 */
	__tcs_buffer_write(drv, tcs_id, 0, msg);
	__tcs_set_trigger(drv, tcs_id, true);

	rpmh_rsc_wait_for_resp(drv, tcs_id);

	return 0;
}


static int rpmh_probe_tcs_config(struct udevice *dev, struct rsc_drv *drv)
{
	struct tcs_type_config {
		u32 type;
		u32 n;
	} tcs_cfg[TCS_TYPE_NR] = { { 0 } };
	ofnode dn = dev_ofnode(dev);
	u32 config, max_tcs, ncpt, offset;
	int i, ret, n, st = 0;
	struct tcs_group *tcs;

	ret = ofnode_read_u32(dn, "qcom,tcs-offset", &offset);
	if (ret)
		return ret;
	drv->tcs_base = drv->base + offset;

	config = readl_relaxed(drv->base + drv->regs[DRV_PRNT_CHLD_CONFIG]);

	max_tcs = config;
	max_tcs &= DRV_NUM_TCS_MASK << (DRV_NUM_TCS_SHIFT * drv->id);
	max_tcs = max_tcs >> (DRV_NUM_TCS_SHIFT * drv->id);

	ncpt = config & (DRV_NCPT_MASK << DRV_NCPT_SHIFT);
	ncpt = ncpt >> DRV_NCPT_SHIFT;

	n = ofnode_read_u32_array(dn, "qcom,tcs-config", (u32*)tcs_cfg, 2 * TCS_TYPE_NR);
	if (n < 0) {
		printf("RPMh: %s: error reading qcom,tcs-config %d\n", dev->name, n);
		return n;
	}

	for (i = 0; i < TCS_TYPE_NR; i++) {
		if (tcs_cfg[i].n > MAX_TCS_PER_TYPE)
			return -EINVAL;
	}

	for (i = 0; i < TCS_TYPE_NR; i++) {
		tcs = &drv->tcs[tcs_cfg[i].type];
		if (tcs->drv)
			return -EINVAL;
		tcs->drv = drv;
		tcs->type = tcs_cfg[i].type;
		tcs->num_tcs = tcs_cfg[i].n;
		tcs->ncpt = ncpt;

		if (!tcs->num_tcs || tcs->type == CONTROL_TCS)
			continue;

		if (st + tcs->num_tcs > max_tcs ||
		    st + tcs->num_tcs >= BITS_PER_BYTE * sizeof(tcs->mask))
			return -EINVAL;

		tcs->mask = ((1 << tcs->num_tcs) - 1) << st;
		tcs->offset = st;
		st += tcs->num_tcs;
	}

	drv->num_tcs = st;

	return 0;
}

static int rpmh_rsc_probe(struct udevice *dev)
{
	ofnode dn = dev_ofnode(dev);
	ofnode rmem, node;
	struct rsc_drv *drv;
	char drv_id[10] = {0};
	int ret;
	u32 rsc_id;

	/*
	 * Even though RPMh doesn't directly use cmd-db, all of its children
	 * do. To avoid adding this check to our children we'll do it now.
	 */
	rmem = ofnode_path("/reserved-memory");
	ofnode_for_each_subnode(node, rmem) {
		if (ofnode_device_is_compatible(node, "qcom,cmd-db"))
			goto found;
	}

	printf("Couldn't find qcom,cmd-db node!\n");
	return -ENODEV;
found:
	ret = cmd_db_init(node);
	if (ret < 0) {
		printf("Couldn't init cmd-db!\n");
		return ret;
	}

	drv = dev_get_priv(dev);

	ret = ofnode_read_u32(dn, "qcom,drv-id", &drv->id);
	if (ret)
		return ret;

	drv->name = ofnode_get_property(dn, "label", NULL);
	if (!drv->name)
		drv->name = dev->name;

	snprintf(drv_id, ARRAY_SIZE(drv_id), "drv-%d", drv->id);
	drv->base = (void __iomem*)dev_read_addr_name(dev, drv_id);
	if (IS_ERR(drv->base))
		return PTR_ERR(drv->base);

	rsc_id = readl_relaxed(drv->base + RSC_DRV_ID);
	drv->ver.major = rsc_id & (MAJOR_VER_MASK << MAJOR_VER_SHIFT);
	drv->ver.major >>= MAJOR_VER_SHIFT;
	drv->ver.minor = rsc_id & (MINOR_VER_MASK << MINOR_VER_SHIFT);
	drv->ver.minor >>= MINOR_VER_SHIFT;

	if (drv->ver.major == 3) {
		printf("RPMh v3 not supported\n");
		return -ENOTSUPP;
	} else
		drv->regs = rpmh_rsc_reg_offset_ver_2_7;

	ret = rpmh_probe_tcs_config(dev, drv);
	if (ret)
		return ret;

	spin_lock_init(&drv->lock);
	init_waitqueue_head(&drv->tcs_wait);
	bitmap_zero(drv->tcs_in_use, MAX_TCS_NR);

	/* Enable the active TCS to send requests immediately */
	writel_relaxed(drv->tcs[ACTIVE_TCS].mask,
		       drv->tcs_base + drv->regs[RSC_DRV_IRQ_ENABLE]);

	spin_lock_init(&drv->client.cache_lock);
	INIT_LIST_HEAD(&drv->client.cache);
	INIT_LIST_HEAD(&drv->client.batch_cache);

	dev_set_drvdata(dev, drv);
	drv->dev = dev;

	printf("RPMh: %s: v%d.%d (priv %p)\n", dev->name, drv->ver.major, drv->ver.minor, dev_get_priv(dev));

	return ret;
}

// static int rpmh_rsc_of_bind(struct udevice *parent)
// {
// 	lists_bind_drivers(parent, false);

// 	return 0;
// }

static const struct udevice_id qcom_rpmh_ids[] = {
	{ .compatible = "qcom,rpmh-rsc" },
	{ }
};

U_BOOT_DRIVER(qcom_rpmh_rsc) = {
	.name		= "qcom_rpmh_rsc",
	.id		= UCLASS_MISC,
	.priv_auto	= sizeof(struct rsc_drv),
	.probe		= rpmh_rsc_probe,
	//.bind		= rpmh_rsc_of_bind,
	.of_match	= qcom_rpmh_ids,
};