// SPDX-License-Identifier: GPL-2.0+
/*
 * (C) Copyright 2005
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 */

#include <common.h>
#include <fdt_support.h>
#include <init.h>
#include <ioports.h>
#include <mpc83xx.h>
#include <asm/mpc8349_pci.h>
#include <i2c.h>
#include <miiphy.h>
#include <asm/mmu.h>
#include <pci.h>
#include <flash.h>
#include <mtd/cfi_flash.h>

DECLARE_GLOBAL_DATA_PTR;

#define IOSYNC			asm("eieio")
#define ISYNC			asm("isync")
#define SYNC			asm("sync")
#define FPW			FLASH_PORT_WIDTH
#define FPWV			FLASH_PORT_WIDTHV

#define DDR_MAX_SIZE_PER_CS	0x20000000

#if defined(DDR_CASLAT_20)
#define TIMING_CASLAT		TIMING_CFG1_CASLAT_20
#define MODE_CASLAT		DDR_MODE_CASLAT_20
#else
#define TIMING_CASLAT		TIMING_CFG1_CASLAT_25
#define MODE_CASLAT		DDR_MODE_CASLAT_25
#endif

#define INITIAL_CS_CONFIG	(CSCONFIG_EN | CSCONFIG_ROW_BIT_12 | \
				CSCONFIG_COL_BIT_9)

/* External definitions */
ulong flash_get_size (ulong base, int banknum);

/* Local functions */
static int detect_num_flash_banks(void);
static long int get_ddr_bank_size(short cs, long *base);
static void set_cs_bounds(short cs, ulong base, ulong size);
static void set_cs_config(short cs, long config);
static void set_ddr_config(void);

/* Local variable */
static volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;

/**************************************************************************
 * Board initialzation after relocation to RAM. Used to detect the number
 * of Flash banks on TQM834x.
 */
int board_early_init_r (void) {
	/* sanity check, IMMARBAR should be mirrored at offset zero of IMMR */
	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
		return 0;

	/* detect the number of Flash banks */
	return detect_num_flash_banks();
}

/**************************************************************************
 * DRAM initalization and size detection
 */
int dram_init(void)
{
	long bank_size;
	long size;
	int cs;

	/* during size detection, set up the max DDRLAW size */
	im->sysconf.ddrlaw[0].bar = CONFIG_SYS_SDRAM_BASE;
	im->sysconf.ddrlaw[0].ar = (LAWAR_EN | LAWAR_SIZE_2G);

	/* set CS bounds to maximum size */
	for(cs = 0; cs < 4; ++cs) {
		set_cs_bounds(cs,
			CONFIG_SYS_SDRAM_BASE + (cs * DDR_MAX_SIZE_PER_CS),
			DDR_MAX_SIZE_PER_CS);

		set_cs_config(cs, INITIAL_CS_CONFIG);
	}

	/* configure ddr controller */
	set_ddr_config();

	udelay(200);

	/* enable DDR controller */
	im->ddr.sdram_cfg = (SDRAM_CFG_MEM_EN |
		SDRAM_CFG_SREN |
		SDRAM_CFG_SDRAM_TYPE_DDR1);
	SYNC;

	/* size detection */
	debug("\n");
	size = 0;
	for(cs = 0; cs < 4; ++cs) {
		debug("\nDetecting Bank%d\n", cs);

		bank_size = get_ddr_bank_size(cs,
			(long *)(CONFIG_SYS_SDRAM_BASE + size));
		size += bank_size;

		debug("DDR Bank%d size: %ld MiB\n\n", cs, bank_size >> 20);

		/* exit if less than one bank */
		if(size < DDR_MAX_SIZE_PER_CS) break;
	}

	gd->ram_size = size;

	return 0;
}

/**************************************************************************
 * checkboard()
 */
int checkboard (void)
{
	puts("Board: TQM834x\n");

#ifdef CONFIG_PCI
	volatile immap_t * immr;
	u32 w, f;

	immr = (immap_t *)CONFIG_SYS_IMMR;
	if (!(immr->reset.rcwh & HRCWH_PCI_HOST)) {
		printf("PCI:   NOT in host mode..?!\n");
		return 0;
	}

	/* get bus width */
	w = 32;
	if (immr->reset.rcwh & HRCWH_64_BIT_PCI)
		w = 64;

	/* get clock */
	f = gd->pci_clk;

	printf("PCI1:  %d bit, %d MHz\n", w, f / 1000000);
#else
	printf("PCI:   disabled\n");
#endif
	return 0;
}


/**************************************************************************
 *
 * Local functions
 *
 *************************************************************************/

/**************************************************************************
 * Detect the number of flash banks (1 or 2). Store it in
 * a global variable tqm834x_num_flash_banks.
 * Bank detection code based on the Monitor code.
 */
static int detect_num_flash_banks(void)
{
	typedef unsigned long FLASH_PORT_WIDTH;
	typedef volatile unsigned long FLASH_PORT_WIDTHV;
	FPWV *bank1_base;
	FPWV *bank2_base;
	FPW bank1_read;
	FPW bank2_read;
	ulong bank1_size;
	ulong bank2_size;
	ulong total_size;

	cfi_flash_num_flash_banks = 2;	/* assume two banks */

	/* Get bank 1 and 2 information */
	bank1_size = flash_get_size(CONFIG_SYS_FLASH_BASE, 0);
	debug("Bank1 size: %lu\n", bank1_size);
	bank2_size = flash_get_size(CONFIG_SYS_FLASH_BASE + bank1_size, 1);
	debug("Bank2 size: %lu\n", bank2_size);
	total_size = bank1_size + bank2_size;

	if (bank2_size > 0) {
		/* Seems like we've got bank 2, but maybe it's mirrored 1 */

		/* Set the base addresses */
		bank1_base = (FPWV *) (CONFIG_SYS_FLASH_BASE);
		bank2_base = (FPWV *) (CONFIG_SYS_FLASH_BASE + bank1_size);

		/* Put bank 2 into CFI command mode and read */
		bank2_base[0x55] = 0x00980098;
		IOSYNC;
		ISYNC;
		bank2_read = bank2_base[0x10];

		/* Read from bank 1 (it's in read mode) */
		bank1_read = bank1_base[0x10];

		/* Reset Flash */
		bank1_base[0] = 0x00F000F0;
		bank2_base[0] = 0x00F000F0;

		if (bank2_read == bank1_read) {
			/*
			 * Looks like just one bank, but not sure yet. Let's
			 * read from bank 2 in autosoelect mode.
			 */
			bank2_base[0x0555] = 0x00AA00AA;
			bank2_base[0x02AA] = 0x00550055;
			bank2_base[0x0555] = 0x00900090;
			IOSYNC;
			ISYNC;
			bank2_read = bank2_base[0x10];

			/* Read from bank 1 (it's in read mode) */
			bank1_read = bank1_base[0x10];

			/* Reset Flash */
			bank1_base[0] = 0x00F000F0;
			bank2_base[0] = 0x00F000F0;

			if (bank2_read == bank1_read) {
				/*
				 * In both CFI command and autoselect modes,
				 * we got the some data reading from Flash.
				 * There is only one mirrored bank.
				 */
				cfi_flash_num_flash_banks = 1;
				total_size = bank1_size;
			}
		}
	}

	debug("Number of flash banks detected: %d\n", cfi_flash_num_flash_banks);

	/* set OR0 and BR0 */
	set_lbc_or(0, OR_GPCM_CSNT | OR_GPCM_ACS_DIV4 | OR_GPCM_SCY_5 |
		   OR_GPCM_TRLX | (-(total_size) & OR_GPCM_AM));
	set_lbc_br(0, (CONFIG_SYS_FLASH_BASE & BR_BA) |
		   (BR_MS_GPCM | BR_PS_32 | BR_V));

	return (0);
}

/*************************************************************************
 * Detect the size of a ddr bank. Sets CS bounds and CS config accordingly.
 */
static long int get_ddr_bank_size(short cs, long *base)
{
	/* This array lists all valid DDR SDRAM configurations, with
	 * Bank sizes in bytes. (Refer to Table 9-27 in the MPC8349E RM).
	 * The last entry has to to have size equal 0 and is igonred during
	 * autodection. Bank sizes must be in increasing order of size
	 */
	struct {
		long row;
		long col;
		long size;
	} conf[] = {
		{CSCONFIG_ROW_BIT_12,	CSCONFIG_COL_BIT_8,	32 << 20},
		{CSCONFIG_ROW_BIT_12,	CSCONFIG_COL_BIT_9,	64 << 20},
		{CSCONFIG_ROW_BIT_12,	CSCONFIG_COL_BIT_10,	128 << 20},
		{CSCONFIG_ROW_BIT_13,	CSCONFIG_COL_BIT_9,	128 << 20},
		{CSCONFIG_ROW_BIT_13,	CSCONFIG_COL_BIT_10,	256 << 20},
		{CSCONFIG_ROW_BIT_13,	CSCONFIG_COL_BIT_11,	512 << 20},
		{CSCONFIG_ROW_BIT_14,	CSCONFIG_COL_BIT_10,	512 << 20},
		{CSCONFIG_ROW_BIT_14,	CSCONFIG_COL_BIT_11,	1024 << 20},
		{0,			0,			0}
	};

	int i;
	int detected;
	long size;

	detected = -1;
	for(i = 0; conf[i].size != 0; ++i) {

		/* set sdram bank configuration */
		set_cs_config(cs, CSCONFIG_EN | conf[i].col | conf[i].row);

		debug("Getting RAM size...\n");
		size = get_ram_size(base, DDR_MAX_SIZE_PER_CS);

		if((size == conf[i].size) && (i == detected + 1))
			detected = i;

		debug("Trying %ld x %ld (%ld MiB) at addr %p, detected: %ld MiB\n",
			conf[i].row,
			conf[i].col,
			conf[i].size >> 20,
			base,
			size >> 20);
	}

	if(detected == -1){
		/* disable empty cs */
		debug("\nNo valid configurations for CS%d, disabling...\n", cs);
		set_cs_config(cs, 0);
		return 0;
	}

	debug("\nDetected configuration %ld x %ld (%ld MiB) at addr %p\n",
			conf[detected].row, conf[detected].col, conf[detected].size >> 20, base);

	/* configure cs ro detected params */
	set_cs_config(cs, CSCONFIG_EN | conf[detected].row |
			conf[detected].col);

	set_cs_bounds(cs, (long)base, conf[detected].size);

	return(conf[detected].size);
}

/**************************************************************************
 * Sets DDR bank CS bounds.
 */
static void set_cs_bounds(short cs, ulong base, ulong size)
{
	debug("Setting bounds %08lx, %08lx for cs %d\n", base, size, cs);
	if(size == 0){
		im->ddr.csbnds[cs].csbnds = 0x00000000;
	} else {
		im->ddr.csbnds[cs].csbnds =
			((base >> CSBNDS_SA_SHIFT) & CSBNDS_SA) |
			(((base + size - 1) >> CSBNDS_EA_SHIFT) &
				CSBNDS_EA);
	}
	SYNC;
}

/**************************************************************************
 * Sets DDR banks CS configuration.
 * config == 0x00000000 disables the CS.
 */
static void set_cs_config(short cs, long config)
{
	debug("Setting config %08lx for cs %d\n", config, cs);
	im->ddr.cs_config[cs] = config;
	SYNC;
}

/**************************************************************************
 * Sets DDR clocks, timings and configuration.
 */
static void set_ddr_config(void) {
	/* clock control */
	im->ddr.sdram_clk_cntl = DDR_SDRAM_CLK_CNTL_SS_EN |
		DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05;
	SYNC;

	/* timing configuration */
	im->ddr.timing_cfg_1 =
		(4 << TIMING_CFG1_PRETOACT_SHIFT) |
		(7 << TIMING_CFG1_ACTTOPRE_SHIFT) |
		(4 << TIMING_CFG1_ACTTORW_SHIFT)  |
		(5 << TIMING_CFG1_REFREC_SHIFT)   |
		(3 << TIMING_CFG1_WRREC_SHIFT)    |
		(3 << TIMING_CFG1_ACTTOACT_SHIFT) |
		(1 << TIMING_CFG1_WRTORD_SHIFT)   |
		(TIMING_CFG1_CASLAT & TIMING_CASLAT);

	im->ddr.timing_cfg_2 =
		TIMING_CFG2_CPO_DEF |
		(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT);
	SYNC;

	/* don't enable DDR controller yet */
	im->ddr.sdram_cfg =
		SDRAM_CFG_SREN |
		SDRAM_CFG_SDRAM_TYPE_DDR1;
	SYNC;

	/* Set SDRAM mode */
	im->ddr.sdram_mode =
		((DDR_MODE_EXT_MODEREG | DDR_MODE_WEAK) <<
			SDRAM_MODE_ESD_SHIFT) |
		((DDR_MODE_MODEREG | DDR_MODE_BLEN_4) <<
			SDRAM_MODE_SD_SHIFT) |
		((DDR_MODE_CASLAT << SDRAM_MODE_SD_SHIFT) &
			MODE_CASLAT);
	SYNC;

	/* Set fast SDRAM refresh rate */
	im->ddr.sdram_interval =
		(DDR_REFINT_166MHZ_7US << SDRAM_INTERVAL_REFINT_SHIFT) |
		(DDR_BSTOPRE << SDRAM_INTERVAL_BSTOPRE_SHIFT);
	SYNC;

	/* Workaround for DDR6 Erratum
	 * see MPC8349E Device Errata Rev.8, 2/2006
	 * This workaround influences the MPC internal "input enables"
	 * dependent on CAS latency and MPC revision. According to errata
	 * sheet the internal reserved registers for this workaround are
	 * not available from revision 2.0 and up.
	 */

	/* Get REVID from register SPRIDR. Skip workaround if rev >= 2.0
	 * (0x200)
	 */
	if ((im->sysconf.spridr & SPRIDR_REVID) < 0x200) {

		/* There is a internal reserved register at IMMRBAR+0x2F00
		 * which has to be written with a certain value defined by
		 * errata sheet.
		 */
		u32 *reserved_p = (u32 *)((u8 *)im + 0x2f00);

#if defined(DDR_CASLAT_20)
		*reserved_p = 0x201c0000;
#else
		*reserved_p = 0x202c0000;
#endif
	}
}

#ifdef CONFIG_OF_BOARD_SETUP
int ft_board_setup(void *blob, bd_t *bd)
{
	ft_cpu_setup(blob, bd);

#ifdef CONFIG_PCI
	ft_pci_setup(blob, bd);
#endif	/* CONFIG_PCI */

	return 0;
}
#endif	/* CONFIG_OF_BOARD_SETUP */