/* Copyright 2014 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:    GPL-2.0+
 */

#include <common.h>
#include <console.h>
#include <malloc.h>
#include <ns16550.h>
#include <nand.h>
#include <i2c.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <spi_flash.h>
#include "../common/qixis.h"
#include "t102xqds_qixis.h"
#include "../common/spl.h"

DECLARE_GLOBAL_DATA_PTR;

phys_size_t get_effective_memsize(void)
{
	return CONFIG_SYS_L3_SIZE;
}

unsigned long get_board_sys_clk(void)
{
	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);

	switch (sysclk_conf & 0x0F) {
	case QIXIS_SYSCLK_83:
		return 83333333;
	case QIXIS_SYSCLK_100:
		return 100000000;
	case QIXIS_SYSCLK_125:
		return 125000000;
	case QIXIS_SYSCLK_133:
		return 133333333;
	case QIXIS_SYSCLK_150:
		return 150000000;
	case QIXIS_SYSCLK_160:
		return 160000000;
	case QIXIS_SYSCLK_166:
		return 166666666;
	}
	return 66666666;
}

unsigned long get_board_ddr_clk(void)
{
	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);

	switch ((ddrclk_conf & 0x30) >> 4) {
	case QIXIS_DDRCLK_100:
		return 100000000;
	case QIXIS_DDRCLK_125:
		return 125000000;
	case QIXIS_DDRCLK_133:
		return 133333333;
	}
	return 66666666;
}

void board_init_f(ulong bootflag)
{
	u32 plat_ratio, sys_clk, ccb_clk;
	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;

#if defined(CONFIG_PPC_T1040) && defined(CONFIG_SPL_NAND_BOOT)
	/*
	 * There is T1040 SoC issue where NOR, FPGA are inaccessible during
	 * NAND boot because IFC signals > IFC_AD7 are not enabled.
	 * This workaround changes RCW source to make all signals enabled.
	 */
	u32 porsr1, pinctl;
#define FSL_CORENET_CCSR_PORSR1_RCW_MASK        0xFF800000

	porsr1 = in_be32(&gur->porsr1);
	pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
	out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
#endif

	/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
	memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));

	/* Update GD pointer */
	gd = (gd_t *)(CONFIG_SPL_GD_ADDR);

	console_init_f();

	/* initialize selected port with appropriate baud rate */
	sys_clk = get_board_sys_clk();
	plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
	ccb_clk = sys_clk * plat_ratio / 2;

	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
		     ccb_clk / 16 / CONFIG_BAUDRATE);

#if defined(CONFIG_SPL_MMC_BOOT)
	puts("\nSD boot...\n");
#elif defined(CONFIG_SPL_SPI_BOOT)
	puts("\nSPI boot...\n");
#elif defined(CONFIG_SPL_NAND_BOOT)
	puts("\nNAND boot...\n");
#endif

	relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
}

void board_init_r(gd_t *gd, ulong dest_addr)
{
	bd_t *bd;

	bd = (bd_t *)(gd + sizeof(gd_t));
	memset(bd, 0, sizeof(bd_t));
	gd->bd = bd;
	bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
	bd->bi_memsize = CONFIG_SYS_L3_SIZE;

	probecpu();
	get_clocks();
	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
			CONFIG_SPL_RELOC_MALLOC_SIZE);
	gd->flags |= GD_FLG_FULL_MALLOC_INIT;

#ifdef CONFIG_SPL_NAND_BOOT
	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
			    (uchar *)CONFIG_ENV_ADDR);
#endif
#ifdef CONFIG_SPL_MMC_BOOT
	mmc_initialize(bd);
	mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
			   (uchar *)CONFIG_ENV_ADDR);
#endif
#ifdef CONFIG_SPL_SPI_BOOT
	fsl_spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
			       (uchar *)CONFIG_ENV_ADDR);
#endif

	gd->env_addr  = (ulong)(CONFIG_ENV_ADDR);
	gd->env_valid = 1;

	i2c_init_all();

	gd->ram_size = initdram(0);

#ifdef CONFIG_SPL_MMC_BOOT
	mmc_boot();
#elif defined(CONFIG_SPL_SPI_BOOT)
	fsl_spi_boot();
#elif defined(CONFIG_SPL_NAND_BOOT)
	nand_boot();
#endif
}