/*
 * Copyright (C) 2016 NXP Semiconductors
 *
 * Configuration settings for the i.MX7S Warp board.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __WARP7_CONFIG_H
#define __WARP7_CONFIG_H

#define CONFIG_BOOTDELAY                1
#include "mx7_common.h"

#define PHYS_SDRAM_SIZE			SZ_512M

#define CONFIG_MXC_UART_BASE		UART1_IPS_BASE_ADDR

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(32 * SZ_1M)

#define CONFIG_BOARD_EARLY_INIT_F

/* MMC Config*/
#define CONFIG_SYS_FSL_ESDHC_ADDR       USDHC3_BASE_ADDR
#define CONFIG_SUPPORT_EMMC_BOOT
#define CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE
#define CONFIG_SYS_MMC_IMG_LOAD_PART	1

#define CONFIG_DFU_ENV_SETTINGS \
	"dfu_alt_info=image raw 0 0x800000;"\
		"u-boot raw 0 0x4000;"\
		"bootimg part 0 1;"\
		"rootfs part 0 2\0" \

#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_DFU_ENV_SETTINGS \
	"script=boot.scr\0" \
	"image=zImage\0" \
	"console=ttymxc0\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_file=imx7d-warp.dtb\0" \
	"fdt_addr=0x83000000\0" \
	"boot_fdt=try\0" \
	"ip_dyn=yes\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcargs=setenv bootargs console=${console},${baudrate} " \
		"root=${mmcroot}\0" \
	"loadbootscript=" \
		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
		"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if run loadfdt; then " \
				"bootz ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"if test ${boot_fdt} = try; then " \
					"bootz; " \
				"else " \
					"echo WARN: Cannot load the DT; " \
				"fi; " \
			"fi; " \
		"else " \
			"bootz; " \
		"fi;\0" \

#define CONFIG_BOOTCOMMAND \
	   "mmc dev ${mmcdev};" \
	   "mmc dev ${mmcdev}; if mmc rescan; then " \
		   "if run loadbootscript; then " \
			   "run bootscript; " \
		   "else " \
			   "if run loadimage; then " \
				   "run mmcboot; " \
			   "fi; " \
		   "fi; " \
	   "fi"

#define CONFIG_SYS_MEMTEST_START	0x80000000
#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x20000000)

#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
#define CONFIG_SYS_HZ			1000

#define CONFIG_STACKSIZE		SZ_128K

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS		1
#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/* FLASH and environment organization */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_SIZE			SZ_8K
#define CONFIG_ENV_IS_IN_MMC

#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
#define CONFIG_SYS_FSL_USDHC_NUM	1

#define CONFIG_SYS_MMC_ENV_DEV		0
#define CONFIG_SYS_MMC_ENV_PART		0
#define CONFIG_MMCROOT			"/dev/mmcblk2p2"

/* USB Configs */
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX7
#define CONFIG_USB_STORAGE
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET

#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS		0
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 /* Only OTG1 port enabled */

#define CONFIG_IMX_THERMAL

#define CONFIG_CI_UDC
#define CONFIG_USBD_HS
#define CONFIG_USB_GADGET_DUALSPEED

#define CONFIG_USB_GADGET
#define CONFIG_USB_FUNCTION_MASS_STORAGE
#define CONFIG_USB_GADGET_DOWNLOAD
#define CONFIG_USB_GADGET_VBUS_DRAW	2

#define CONFIG_G_DNL_VENDOR_NUM		0x0525
#define CONFIG_G_DNL_PRODUCT_NUM	0xa4a5
#define CONFIG_G_DNL_MANUFACTURER	"FSL"

/* USB Device Firmware Update support */
#define CONFIG_USB_FUNCTION_DFU
#define CONFIG_DFU_MMC
#define CONFIG_SYS_DFU_DATA_BUF_SIZE	SZ_16M
#define DFU_DEFAULT_POLL_TIMEOUT	300

#endif