// SPDX-License-Identifier: GPL-2.0+ OR X11
/*
 * NXP ls1028AQDS device tree source
 *
 * Copyright 2019 NXP
 *
 */

/dts-v1/;

#include "fsl-ls1028a.dtsi"

/ {
	model = "NXP Layerscape 1028a QDS Board";
	compatible = "fsl,ls1028a-qds", "fsl,ls1028a";
	aliases {
		spi0 = &fspi;
	};

};

&dspi0 {
	status = "okay";
};

&dspi1 {
	status = "okay";
};

&dspi2 {
	status = "okay";
};

&esdhc0 {
	status = "okay";
};

&esdhc1 {
	status = "okay";

};

&fspi {
	status = "okay";

	mt35xu02g0: flash@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "jedec,spi-nor";
		spi-max-frequency = <50000000>;
		reg = <0>;
		spi-rx-bus-width = <8>;
		spi-tx-bus-width = <1>;
	};
};

&i2c0 {
	status = "okay";
	u-boot,dm-pre-reloc;

	fpga@66 {
		#address-cells = <1>;
		#size-cells = <0>;
		compatible = "simple-mfd";
		reg = <0x66>;

		mux-mdio@54 {
			#address-cells = <1>;
			#size-cells = <0>;
			compatible = "mdio-mux-i2creg";
			reg = <0x54>;
			#mux-control-cells = <1>;
			mux-reg-masks = <0x54 0xf0>;
			mdio-parent-bus = <&mdio0>;

			/* on-board MDIO with a single RGMII PHY */
			mdio@00 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x00>;

				qds_phy0: phy@5 {
					reg = <5>;
				};
			};
			/* slot 1 */
			slot1: mdio@40 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x40>;
			};
			/* slot 2 */
			slot2: mdio@50 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x50>;
			};
			/* slot 3 */
			slot3: mdio@60 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x60>;
			};
			/* slot 4 */
			slot4: mdio@70 {
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x70>;
			};
		};
	};

	i2c-mux@77 {
		compatible = "nxp,pca9547";
		reg = <0x77>;
		#address-cells = <1>;
		#size-cells = <0>;
	};
};

&i2c1 {
	status = "okay";

	rtc@51 {
		compatible = "pcf2127-rtc";
		reg = <0x51>;
	};
};

&i2c2 {
	status = "okay";
};

&i2c3 {
	status = "okay";
};

&i2c4 {
	status = "okay";
};

&i2c5 {
	status = "okay";
};

&i2c6 {
	status = "okay";
};

&i2c7 {
	status = "okay";
};

&sata {
	status = "okay";
};

&serial0 {
	status = "okay";
};

&serial1 {
	status = "okay";
};

&usb1 {
	status = "okay";
};

&usb2 {
	status = "okay";
};

&enetc1 {
	status = "okay";
	phy-mode = "rgmii";
	phy-handle = <&qds_phy0>;
};

&mdio0 {
	status = "okay";
};