CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_POSITION_INDEPENDENT=y
CONFIG_ARCH_SNAPDRAGON=y
CONFIG_DEFAULT_DEVICE_TREE="dragonboard845c"
CONFIG_SYS_LOAD_ADDR=0x0
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_BOOTSTD_FULL=y
# CONFIG_BOOTMETH_EXTLINUX is not set
# CONFIG_BOOTMETH_VBE is not set
# CONFIG_BOOTMETH_SCRIPT is not set
CONFIG_BOOTDELAY=1
CONFIG_USE_PREBOOT=y
CONFIG_LOG_MAX_LEVEL=9
CONFIG_LOG_DEFAULT_LEVEL=4
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_MAXARGS=64
CONFIG_SYS_CBSIZE=512
CONFIG_CMD_BOOTMENU=y
CONFIG_CMD_CLK=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_MMC=y
CONFIG_CMD_PART=y
CONFIG_CMD_UFS=y
CONFIG_CMD_USB=y
CONFIG_CMD_CAT=y
CONFIG_CMD_BMP=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_CMD_LOG=y
CONFIG_EFI_PARTITION=y
# CONFIG_NET is not set
CONFIG_CLK=y
CONFIG_CLK_QCOM_QCS404=y
CONFIG_CLK_QCOM_SDM845=y
CONFIG_MSM_GPIO=y
CONFIG_QCOM_PMIC_GPIO=y
CONFIG_DM_KEYBOARD=y
CONFIG_BUTTON_KEYBOARD=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_MSM=y
CONFIG_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_QCOM_QCS404=y
CONFIG_PINCTRL_QCOM_SDM845=y
CONFIG_DM_PMIC=y
CONFIG_PMIC_QCOM=y
CONFIG_SCSI=y
CONFIG_DM_SCSI=y
CONFIG_MSM_GENI_SERIAL=y
CONFIG_SPMI_MSM=y
CONFIG_SYSINFO=y
CONFIG_SYSINFO_SMBIOS=y
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
CONFIG_USB_DWC3=y
CONFIG_USB_STORAGE=y
CONFIG_UFS=y
CONFIG_VIDEO=y
# CONFIG_VIDEO_FONT_8X16 is not set
CONFIG_VIDEO_FONT_16X32=y
CONFIG_SYS_WHITE_ON_BLACK=y
CONFIG_NO_FB_CLEAR=y
CONFIG_VIDEO_SIMPLE=y
CONFIG_HEXDUMP=y
# CONFIG_GENERATE_SMBIOS_TABLE is not set
CONFIG_LMB_MAX_REGIONS=64

CONFIG_BAUDRATE=115200

# Uncomment to enable UART pre-relocation
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_ANNOUNCE=y
# This is the address of the debug-uart peripheral
# The value here is for SDM845, other platforms will vary
CONFIG_DEBUG_UART_BASE=0xa84000
# Boards older than ~2018 pre-date the GENI driver and unfortunately
# aren't supported here
CONFIG_DEBUG_UART_MSM_GENI=y
# For sdm845 this is the UART clock rate
CONFIG_DEBUG_UART_CLOCK=7372800
# Most newer boards have an oversampling value of 16 instead
# of 32, they need the clock rate to be doubled
#CONFIG_DEBUG_UART_CLOCK=14745600

CONFIG_LOG=y
CONFIG_HEXDUMP=y
CONFIG_CMD_LOG=y
CONFIG_LOG_MAX_LEVEL=9
CONFIG_LOG_DEFAULT_LEVEL=9
CONFIG_LOGLEVEL=9