/*
 * Copyright (C) 2014 Stefan Roese <sr@denx.de>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _CONFIG_DB_MV7846MP_GP_H
#define _CONFIG_DB_MV7846MP_GP_H

/*
 * High Level Configuration Options (easy to change)
 */
#define CONFIG_ARMADA_XP		/* SOC Family Name */
#define CONFIG_DB_784MP_GP		/* Board target name for DDR training */

#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_BOARDINFO_LATE

#define	CONFIG_SYS_TEXT_BASE	0x04000000
#define CONFIG_SYS_TCLK		250000000	/* 250MHz */

/*
 * Commands configuration
 */
#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IDE
#define CONFIG_CMD_PING
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
#define CONFIG_CMD_TFTPPUT
#define CONFIG_CMD_TIME

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_I2C_MVTWSI_BASE0		MVEBU_TWSI_BASE
#define CONFIG_SYS_I2C_SLAVE		0x0
#define CONFIG_SYS_I2C_SPEED		100000

/* SPI NOR flash default params, used by sf commands */
#define CONFIG_SF_DEFAULT_SPEED		1000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_3
#define CONFIG_SPI_FLASH_STMICRO

/* Environment in SPI NOR flash */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET		(1 << 20) /* 1MiB in */
#define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
#define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */

#define CONFIG_PHY_MARVELL		/* there is a marvell phy */
#define CONFIG_PHY_ADDR			{ 0x10, 0x11, 0x12, 0x13 }
#define CONFIG_SYS_NETA_INTERFACE_TYPE	PHY_INTERFACE_MODE_QSGMII
#define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */
#define CONFIG_RESET_PHY_R

#define CONFIG_SYS_CONSOLE_INFO_QUIET	/* don't print console @ startup */
#define CONFIG_SYS_ALT_MEMTEST

/* SATA support */
#ifdef CONFIG_CMD_IDE
#define __io
#define CONFIG_IDE_PREINIT
#define CONFIG_MVSATA_IDE

/* Needs byte-swapping for ATA data register */
#define CONFIG_IDE_SWAP_IO

#define CONFIG_SYS_ATA_REG_OFFSET	0x0100 /* Offset for register access */
#define CONFIG_SYS_ATA_DATA_OFFSET	0x0100 /* Offset for data I/O */
#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100

/* Each 8-bit ATA register is aligned to a 4-bytes address */
#define CONFIG_SYS_ATA_STRIDE		4

/* CONFIG_CMD_IDE requires some #defines for ATA registers */
#define CONFIG_SYS_IDE_MAXBUS		2
#define CONFIG_SYS_IDE_MAXDEVICE	CONFIG_SYS_IDE_MAXBUS

/* ATA registers base is at SATA controller base */
#define CONFIG_SYS_ATA_BASE_ADDR	MVEBU_AXP_SATA_BASE
#define CONFIG_SYS_ATA_IDE0_OFFSET	0x2000
#define CONFIG_SYS_ATA_IDE1_OFFSET	0x4000

#define CONFIG_DOS_PARTITION
#endif /* CONFIG_CMD_IDE */

/*
 * mv-common.h should be defined after CMD configs since it used them
 * to enable certain macros
 */
#include "mv-common.h"

/*
 * Memory layout while starting into the bin_hdr via the
 * BootROM:
 *
 * 0x4000.4000 - 0x4003.4000	headers space (192KiB)
 * 0x4000.4030			bin_hdr start address
 * 0x4003.4000 - 0x4004.7c00	BootROM memory allocations (15KiB)
 * 0x4007.fffc			BootROM stack top
 *
 * The address space between 0x4007.fffc and 0x400f.fff is not locked in
 * L2 cache thus cannot be used.
 */

/* SPL */
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE		0x40004030
#define CONFIG_SPL_MAX_SIZE		((128 << 10) - 0x4030)

#define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + (128 << 10))
#define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)

#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
					 CONFIG_SPL_BSS_MAX_SIZE)
#define CONFIG_SYS_SPL_MALLOC_SIZE	(16 << 10)

#define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)

#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT

/* SPL related SPI defines */
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_BUS		0
#define CONFIG_SPL_SPI_CS		0
#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x20000

/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
#define CONFIG_SYS_MVEBU_DDR
#define CONFIG_SPD_EEPROM		0x4e

#endif /* _CONFIG_DB_MV7846MP_GP_H */