/*
 * (C) Copyright 2007
 * Stefan Roese, DENX Software Engineering, sr@denx.de.
 *
 *  Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+ 
 */

#include <asm-offsets.h>
#include <ppc_asm.tmpl>
#include <config.h>
#include <asm/mmu.h>

/**************************************************************************
 * TLB TABLE
 *
 * This table is used by the cpu boot code to setup the initial tlb
 * entries. Rather than make broad assumptions in the cpu source tree,
 * this table lets each board set things up however they like.
 *
 *  Pointer to the table is returned in r1
 *
 *************************************************************************/
	.section .bootpg,"ax"
	.globl tlbtab

tlbtab:
	tlbtab_start

	/*
	 * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
	 * speed up boot process. It is patched after relocation to enable SA_I
	 */
#ifndef CONFIG_NAND_SPL
	tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 0, AC_RWX | SA_G)
#else
	tlbentry(CONFIG_SYS_NAND_BOOT_SPL_SRC, SZ_4K, CONFIG_SYS_NAND_BOOT_SPL_SRC, 0, AC_RWX | SA_G)
	tlbentry(CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, 0, AC_RWX | SA_IG)
#endif

	/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
	tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G)

	/* PCI base & peripherals */
	tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, CONFIG_SYS_PCI_BASE, 0, AC_RW | SA_IG)

	tlbentry(CONFIG_SYS_NVRAM_BASE_ADDR, SZ_256M, CONFIG_SYS_NVRAM_BASE_ADDR, 0, AC_RWX | SA_W|SA_I)
	tlbentry(CONFIG_SYS_NAND_ADDR, SZ_4K, CONFIG_SYS_NAND_ADDR, 0, AC_RWX | SA_W|SA_I)

	/* PCI */
	tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 0, AC_RW | SA_IG)
	tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 0, AC_RW | SA_IG)
	tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 0, AC_RW | SA_IG)
	tlbentry(CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 0, AC_RW | SA_IG)

	/* USB 2.0 Device */
	tlbentry(CONFIG_SYS_USB_DEVICE, SZ_1K, CONFIG_SYS_USB_DEVICE, 0, AC_RW | SA_IG)

	tlbtab_end

#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
	/*
	 * For NAND booting the first TLB has to be reconfigured to full size
	 * and with caching disabled after running from RAM!
	 */
#define TLB00	TLB0(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M)
#define TLB01	TLB1(CONFIG_SYS_BOOT_BASE_ADDR, 0)
#define TLB02	TLB2(AC_RWX | SA_IG)

	.globl	reconfig_tlb0
reconfig_tlb0:
	sync
	isync
	addi	r4,r0,0x0000		/* TLB entry #0 */
	lis	r5,TLB00@h
	ori	r5,r5,TLB00@l
	tlbwe	r5,r4,0x0000		/* Save it out */
	lis	r5,TLB01@h
	ori	r5,r5,TLB01@l
	tlbwe	r5,r4,0x0001		/* Save it out */
	lis	r5,TLB02@h
	ori	r5,r5,TLB02@l
	tlbwe	r5,r4,0x0002		/* Save it out */
	sync
	isync
	blr
#endif