/*
 * Copyright (C) 2016 Stefan Roese <sr@denx.de>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _CONFIG_MVEBU_ARMADA_8K_H
#define _CONFIG_MVEBU_ARMADA_8K_H

/*
 * High Level Configuration Options (easy to change)
 */
#define CONFIG_SYS_TCLK		250000000	/* 250MHz */

#define CONFIG_DISPLAY_BOARDINFO_LATE

#define	CONFIG_SYS_TEXT_BASE	0x00000000

/* additions for new ARM relocation support */
#define CONFIG_SYS_SDRAM_BASE	0x00000000

#define CONFIG_NR_DRAM_BANKS	1

/* auto boot */
#define CONFIG_PREBOOT

#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, \
					  115200, 230400, 460800, 921600 }

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs  */
#define CONFIG_INITRD_TAG		/* enable INITRD tag */
#define CONFIG_SETUP_MEMORY_TAGS	/* enable memory tag */

#define	CONFIG_SYS_CBSIZE	1024	/* Console I/O Buff Size */
#define	CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE \
		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */

/*
 * Size of malloc() pool
 */
#define CONFIG_SYS_MALLOC_LEN	(4 << 20) /* 4MiB for malloc() */

/*
 * Other required minimal configurations
 */
#define CONFIG_SYS_LONGHELP
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
#define CONFIG_ARCH_CPU_INIT		/* call arch_cpu_init() */
#define CONFIG_SYS_LOAD_ADDR	0x00800000	/* default load adr- 8M */
#define CONFIG_SYS_MEMTEST_START 0x00800000	/* 8M */
#define CONFIG_SYS_MEMTEST_END	0x00ffffff	/*(_16M -1) */
#define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
#define CONFIG_SYS_MAXARGS	32	/* max number of command args */

#define CONFIG_SYS_ALT_MEMTEST

/* End of 16M scrubbed by training in bootrom */
#define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_TEXT_BASE + 0xFF0000)

/*
 * SPI Flash configuration
 */
#define CONFIG_KIRKWOOD_SPI
#define CONFIG_ENV_SPI_BUS		0
#define CONFIG_ENV_SPI_CS		0

/* SPI NOR flash default params, used by sf commands */
#define CONFIG_SF_DEFAULT_SPEED		1000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE

/* Environment in SPI NOR flash */
#ifdef CONFIG_MVEBU_SPI_BOOT
/* Environment in NAND flash */
#endif

#define CONFIG_ENV_OFFSET		0x180000 /* as Marvell U-Boot version */
#define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
#define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */

#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_MAX_CHIPS	1
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_USE_FLASH_BBT

/*
 * Ethernet Driver configuration
 */
#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
#define CONFIG_PHY_GIGE		/* GbE speed/duplex detect */
#define CONFIG_ARP_TIMEOUT	200
#define CONFIG_NET_RETRY_COUNT	50

#define CONFIG_USB_MAX_CONTROLLER_COUNT (3 + 3)

/* USB ethernet */
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_ETHER_MCS7830
#define CONFIG_USB_ETHER_RTL8152
#define CONFIG_USB_ETHER_SMSC95XX

/*
 * SATA/SCSI/AHCI configuration
 */
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_LIBATA
#define CONFIG_LBA48
#define CONFIG_SYS_64BIT_LBA

#define CONFIG_SYS_SCSI_MAX_SCSI_ID	2
#define CONFIG_SYS_SCSI_MAX_LUN		1
#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
					 CONFIG_SYS_SCSI_MAX_LUN)

#define CONFIG_SUPPORT_VFAT

/*
 * PCI configuration
 */
#ifdef CONFIG_PCIE_DW_MVEBU
#define CONFIG_E1000
#define CONFIG_CMD_PCI
#endif

#endif /* _CONFIG_MVEBU_ARMADA_8K_H */