include/configs/imx8mn_evk.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2018 NXP
 */

#ifndef __IMX8MN_EVK_H
#define __IMX8MN_EVK_H

#include <linux/sizes.h>
#include <linux/stringify.h>
#include <asm/arch/imx-regs.h>

#define CONFIG_SYS_BOOTM_LEN		(32 * SZ_1M)

#define CONFIG_SPL_MAX_SIZE		(148 * 1024)
#define CONFIG_SYS_MONITOR_LEN		SZ_512K
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
#define CONFIG_SYS_UBOOT_BASE	\
	(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_STACK		0x95fff0
#define CONFIG_SPL_BSS_START_ADDR	0x00950000
#define CONFIG_SPL_BSS_MAX_SIZE		SZ_8K	/* 8 KB */
#define CONFIG_SYS_SPL_MALLOC_START	0x42200000
#define CONFIG_SYS_SPL_MALLOC_SIZE	SZ_512K	/* 512 KB */
#define CONFIG_SYS_ICACHE_OFF
#define CONFIG_SYS_DCACHE_OFF

/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
#define CONFIG_MALLOC_F_ADDR		0x00940000

/* For RAW image gives a error info not panic */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE

#endif

/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"script=boot.scr\0" \
	"image=Image.itb\0" \
	"console=ttymxc1,115200\0" \
	"fdt_addr=0x43000000\0"			\
	"fdt_high=0xffffffffffffffff\0"		\
	"boot_fit=try\0" \
	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
	"initrd_addr=0x43800000\0"		\
	"initrd_high=0xffffffffffffffff\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcautodetect=yes\0" \
	"mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
		"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"if test ${boot_fit} = yes || test ${boot_fit} = try; then " \
			"bootm ${loadaddr}; " \
		"else " \
			"if run loadfdt; then " \
				"booti ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"echo WARN: Cannot load the DT; " \
			"fi; " \
		"fi;\0" \
	"netargs=setenv bootargs console=${console} " \
		"root=/dev/nfs " \
		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
		"run netargs;  " \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"${get_cmd} ${loadaddr} ${image}; " \
		"if test ${boot_fit} = yes || test ${boot_fit} = try; then " \
			"bootm ${loadaddr}; " \
		"else " \
			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
				"booti ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"echo WARN: Cannot load the DT; " \
			"fi; " \
		"fi;\0"

#define CONFIG_BOOTCOMMAND \
	   "mmc dev ${mmcdev}; if mmc rescan; then " \
		   "if run loadbootscript; then " \
			   "run bootscript; " \
		   "else " \
			   "if run loadimage; then " \
				   "run mmcboot; " \
			   "else run netboot; " \
			   "fi; " \
		   "fi; " \
	   "fi;"

/* Link Definitions */
#define CONFIG_LOADADDR			0x40480000

#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR

#define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE        0x200000
#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		SZ_32M

#define CONFIG_SYS_SDRAM_BASE           0x40000000
#define PHYS_SDRAM                      0x40000000
#define PHYS_SDRAM_SIZE			0x80000000 /* 2GB DDR */

#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR

/* Monitor Command Prompt */
#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
#define CONFIG_SYS_CBSIZE		2048
#define CONFIG_SYS_MAXARGS		64
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)

/* USDHC */
#define CONFIG_FSL_USDHC

#define CONFIG_SYS_FSL_USDHC_NUM	2
#define CONFIG_SYS_FSL_ESDHC_ADDR	0

#define CONFIG_SYS_MMC_IMG_LOAD_PART	1

#define CONFIG_SYS_I2C_SPEED		100000

#endif