include/configs/nitrogen6x.h

/*
 * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
 *
 * Configuration settings for the Boundary Devices Nitrogen6X
 * and Freescale i.MX6Q Sabre Lite boards.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include "mx6_common.h"

#define CONFIG_MACH_TYPE	3769

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_MISC_INIT_R
#define CONFIG_USBD_HS
#define CONFIG_USB_ETHER
#define CONFIG_USB_ETH_CDC
#define CONFIG_NETCONSOLE

#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE	       UART2_BASE

#ifdef CONFIG_CMD_SF
#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS  0
#define CONFIG_SF_DEFAULT_CS   0
#define CONFIG_SF_DEFAULT_SPEED 25000000
#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
#endif

/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED		100000
#define CONFIG_I2C_EDID

/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR      0
#define CONFIG_SYS_FSL_USDHC_NUM       2

#ifdef CONFIG_MX6Q
#define CONFIG_CMD_SATA
#endif

/*
 * SATA Configs
 */
#ifdef CONFIG_CMD_SATA
#define CONFIG_DWC_AHSATA
#define CONFIG_SYS_SATA_MAX_DEVICE	1
#define CONFIG_DWC_AHSATA_PORT_ID	0
#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
#define CONFIG_LIBATA
#endif

#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE			ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE		RGMII
#define CONFIG_ETHPRIME			"FEC"
#define CONFIG_FEC_MXC_PHYADDR		6
#define CONFIG_PHYLIB
#define CONFIG_PHY_MICREL
#define CONFIG_PHY_MICREL_KSZ9021

/* USB Configs */
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_ETHER_MCS7830
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */
#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS	0
#define CONFIG_USB_KEYBOARD
#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP

/* Miscellaneous commands */
#define CONFIG_CMD_BMODE

/* Framebuffer and LCD */
#define CONFIG_VIDEO
#define CONFIG_VIDEO_IPUV3
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_VIDEO_BMP_GZIP
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (6 * 1024 * 1024)
#define CONFIG_BMP_16BPP
#define CONFIG_IPUV3_CLK 260000000
#define CONFIG_CMD_HDMIDETECT
#define CONFIG_CONSOLE_MUX
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP

#define CONFIG_PREBOOT                 ""

#ifdef CONFIG_CMD_SATA
#define CONFIG_DRIVE_SATA "sata "
#else
#define CONFIG_DRIVE_SATA
#endif

#ifdef CONFIG_CMD_MMC
#define CONFIG_DRIVE_MMC "mmc "
#else
#define CONFIG_DRIVE_MMC
#endif

#ifdef CONFIG_USB_STORAGE
#define CONFIG_DRIVE_USB "usb "
#else
#define CONFIG_DRIVE_USB
#endif

#define CONFIG_DRIVE_TYPES CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC CONFIG_DRIVE_USB
#define CONFIG_UMSDEVS CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC

#if defined(CONFIG_SABRELITE)
#define CONFIG_EXTRA_ENV_SETTINGS \
	"script=boot.scr\0" \
	"uimage=uImage\0" \
	"console=ttymxc1\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_file=imx6q-sabrelite.dtb\0" \
	"fdt_addr=0x18000000\0" \
	"boot_fdt=try\0" \
	"ip_dyn=yes\0" \
	"mmcdevs=0 1\0" \
	"mmcpart=1\0" \
	"mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
	"mmcargs=setenv bootargs console=${console},${baudrate} " \
		"root=${mmcroot}\0" \
	"loadbootscript=" \
		"load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
		"source\0" \
	"loaduimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
	"loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if run loadfdt; then " \
				"bootm ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"if test ${boot_fdt} = try; then " \
					"bootm; " \
				"else " \
					"echo WARN: Cannot load the DT; " \
				"fi; " \
			"fi; " \
		"else " \
			"bootm; " \
		"fi;\0" \
	"netargs=setenv bootargs console=${console},${baudrate} " \
		"root=/dev/nfs " \
	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
		"netboot=echo Booting from net ...; " \
		"run netargs; " \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"${get_cmd} ${uimage}; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
				"bootm ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"if test ${boot_fdt} = try; then " \
					"bootm; " \
				"else " \
					"echo WARN: Cannot load the DT; " \
				"fi; " \
			"fi; " \
		"else " \
			"bootm; " \
		"fi;\0"

#define CONFIG_BOOTCOMMAND \
	"for mmcdev in ${mmcdevs}; do " \
		"mmc dev ${mmcdev}; " \
		"if mmc rescan; then " \
			"if run loadbootscript; then " \
				"run bootscript; " \
			"else " \
				"if run loaduimage; then " \
					"run mmcboot; " \
				"fi; " \
			"fi; " \
		"fi; " \
	"done; " \
	"run netboot; "
#else
#define CONFIG_EXTRA_ENV_SETTINGS \
	"bootdevs=" CONFIG_DRIVE_TYPES "\0" \
	"umsdevs=" CONFIG_UMSDEVS "\0" \
	"console=ttymxc1\0" \
	"clearenv=if sf probe || sf probe || sf probe 1 ; then " \
		"sf erase 0xc0000 0x2000 && " \
		"echo restored environment to factory default ; fi\0" \
	"bootcmd=for dtype in ${bootdevs}" \
		"; do " \
			"if itest.s \"xusb\" == \"x${dtype}\" ; then " \
				"usb start ;" \
			"fi; " \
			"for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
				"load " \
					"${dtype} ${disk}:1 " \
					"10008000 " \
					"/6x_bootscript" \
					"&& source 10008000 ; " \
			"done ; " \
		"done; " \
		"setenv stdout serial,vga ; " \
		"echo ; echo 6x_bootscript not found ; " \
		"echo ; echo serial console at 115200, 8N1 ; echo ; " \
		"echo details at http://boundarydevices.com/6q_bootscript ; " \
		"setenv stdout serial;" \
		"setenv stdin serial,usbkbd;" \
		"for dtype in ${umsdevs} ; do " \
			"if itest.s sata == ${dtype}; then " \
				"initcmd='sata init' ;" \
			"else " \
				"initcmd='mmc rescan' ;" \
			"fi; " \
			"for disk in 0 1 ; do " \
				"if $initcmd && $dtype dev $disk ; then " \
					"setenv stdout serial,vga; " \
					"echo expose ${dtype} ${disk} " \
						"over USB; " \
					"ums 0 $dtype $disk ;" \
				"fi; " \
		"	done; " \
		"done ;" \
		"setenv stdout serial,vga; " \
		"echo no block devices found;" \
		"\0" \
	"initrd_high=0xffffffff\0" \
	"upgradeu=for dtype in ${bootdevs}" \
		"; do " \
		"for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
			"load ${dtype} ${disk}:1 10008000 " \
				"/6x_upgrade " \
				"&& source 10008000 ; " \
		"done ; " \
	"done\0" \

#endif
/* Miscellaneous configurable options */
#define CONFIG_SYS_MEMTEST_START       0x10000000
#define CONFIG_SYS_MEMTEST_END	       0x10010000
#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS	       1
#define PHYS_SDRAM		       MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE	       PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/* Environment organization */
#define CONFIG_ENV_SIZE			(8 * 1024)

#if defined(CONFIG_SABRELITE)
#define CONFIG_ENV_IS_IN_MMC
#else
#define CONFIG_ENV_IS_IN_SPI_FLASH
#endif

#if defined(CONFIG_ENV_IS_IN_MMC)
#define CONFIG_ENV_OFFSET		(6 * 64 * 1024)
#define CONFIG_SYS_MMC_ENV_DEV		0
#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
#define CONFIG_ENV_OFFSET		(768 * 1024)
#define CONFIG_ENV_SECT_SIZE		(8 * 1024)
#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
#endif

#define CONFIG_CMD_BMP

#define CONFIG_SYS_ALT_MEMTEST

/*
 * PCI express
 */
#ifdef CONFIG_CMD_PCI
#define CONFIG_PCI
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIE_IMX
#endif

#define CONFIG_USB_FUNCTION_MASS_STORAGE

#define CONFIG_USB_FUNCTION_FASTBOOT
#define CONFIG_CMD_FASTBOOT
#define CONFIG_ANDROID_BOOT_IMAGE
#define CONFIG_FASTBOOT_BUF_ADDR   CONFIG_SYS_LOAD_ADDR
#define CONFIG_FASTBOOT_BUF_SIZE   0x07000000

#endif	       /* __CONFIG_H */