| Tom Rini | 83d290c | 2018-05-06 17:58:06 -0400 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0 |
| Jorge Ramirez-Ortiz | ccaa83f | 2017-06-26 15:52:47 +0200 | [diff] [blame] | 2 | /* |
| 3 | * DTS File for HiSilicon Poplar Development Board |
| 4 | * |
| 5 | * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd. |
| Jorge Ramirez-Ortiz | ccaa83f | 2017-06-26 15:52:47 +0200 | [diff] [blame] | 6 | */ |
| 7 | |
| 8 | /dts-v1/; |
| 9 | |
| 10 | #include <dt-bindings/gpio/gpio.h> |
| 11 | #include "hi3798cv200.dtsi" |
| 12 | |
| 13 | / { |
| 14 | model = "HiSilicon Poplar Development Board"; |
| 15 | compatible = "hisilicon,hi3798cv200-poplar", "hisilicon,hi3798cv200"; |
| 16 | |
| 17 | aliases { |
| 18 | serial0 = &uart0; |
| 19 | serial2 = &uart2; |
| 20 | }; |
| 21 | |
| 22 | chosen { |
| 23 | stdout-path = "serial0:115200n8"; |
| 24 | }; |
| 25 | |
| 26 | memory@0 { |
| 27 | device_type = "memory"; |
| 28 | reg = <0x0 0x0 0x0 0x80000000>; |
| 29 | }; |
| 30 | |
| 31 | leds { |
| 32 | compatible = "gpio-leds"; |
| 33 | |
| 34 | user-led0 { |
| 35 | label = "USER-LED0"; |
| 36 | gpios = <&gpio6 3 GPIO_ACTIVE_LOW>; |
| 37 | linux,default-trigger = "heartbeat"; |
| 38 | default-state = "off"; |
| 39 | }; |
| 40 | |
| 41 | user-led1 { |
| 42 | label = "USER-LED1"; |
| 43 | gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; |
| 44 | linux,default-trigger = "mmc0"; |
| 45 | default-state = "off"; |
| 46 | }; |
| 47 | |
| 48 | user-led2 { |
| 49 | label = "USER-LED2"; |
| 50 | gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; |
| 51 | linux,default-trigger = "none"; |
| 52 | default-state = "off"; |
| 53 | }; |
| 54 | |
| 55 | user-led3 { |
| 56 | label = "USER-LED3"; |
| 57 | gpios = <&gpio10 6 GPIO_ACTIVE_LOW>; |
| 58 | linux,default-trigger = "cpu0"; |
| 59 | default-state = "off"; |
| 60 | }; |
| 61 | }; |
| 62 | }; |
| 63 | |
| 64 | &gmac1 { |
| 65 | status = "okay"; |
| 66 | #address-cells = <1>; |
| 67 | #size-cells = <0>; |
| 68 | phy-handle = <ð_phy1>; |
| 69 | phy-mode = "rgmii"; |
| 70 | hisilicon,phy-reset-delays-us = <10000 10000 30000>; |
| 71 | |
| 72 | eth_phy1: phy@3 { |
| 73 | reg = <3>; |
| 74 | }; |
| 75 | }; |
| 76 | |
| 77 | &gpio1 { |
| 78 | status = "okay"; |
| 79 | gpio-line-names = "LS-GPIO-E", "", |
| 80 | "", "", |
| 81 | "", "LS-GPIO-F", |
| 82 | "", "LS-GPIO-J"; |
| 83 | }; |
| 84 | |
| 85 | &gpio2 { |
| 86 | status = "okay"; |
| 87 | gpio-line-names = "LS-GPIO-H", "LS-GPIO-I", |
| 88 | "LS-GPIO-L", "LS-GPIO-G", |
| 89 | "LS-GPIO-K", "", |
| 90 | "", ""; |
| 91 | }; |
| 92 | |
| 93 | &gpio3 { |
| 94 | status = "okay"; |
| 95 | gpio-line-names = "", "", |
| 96 | "", "", |
| 97 | "LS-GPIO-C", "", |
| 98 | "", "LS-GPIO-B"; |
| 99 | }; |
| 100 | |
| 101 | &gpio4 { |
| 102 | status = "okay"; |
| 103 | gpio-line-names = "", "", |
| 104 | "", "", |
| 105 | "", "LS-GPIO-D", |
| 106 | "", ""; |
| 107 | }; |
| 108 | |
| 109 | &gpio5 { |
| 110 | status = "okay"; |
| 111 | gpio-line-names = "", "USER-LED-1", |
| 112 | "USER-LED-2", "", |
| 113 | "", "LS-GPIO-A", |
| 114 | "", ""; |
| 115 | }; |
| 116 | |
| 117 | &gpio6 { |
| 118 | status = "okay"; |
| 119 | gpio-line-names = "", "", |
| 120 | "", "USER-LED-0", |
| 121 | "", "", |
| 122 | "", ""; |
| 123 | }; |
| 124 | |
| 125 | &gpio10 { |
| 126 | status = "okay"; |
| 127 | gpio-line-names = "", "", |
| 128 | "", "", |
| 129 | "", "", |
| 130 | "USER-LED-3", ""; |
| 131 | }; |
| 132 | |
| 133 | &i2c0 { |
| 134 | status = "okay"; |
| 135 | label = "LS-I2C0"; |
| 136 | }; |
| 137 | |
| 138 | &i2c2 { |
| 139 | status = "okay"; |
| 140 | label = "LS-I2C1"; |
| 141 | }; |
| 142 | |
| 143 | &ir { |
| 144 | status = "okay"; |
| 145 | }; |
| 146 | |
| 147 | &spi0 { |
| 148 | status = "okay"; |
| 149 | label = "LS-SPI0"; |
| 150 | }; |
| 151 | |
| 152 | &uart0 { |
| 153 | status = "okay"; |
| 154 | }; |
| 155 | |
| 156 | &uart2 { |
| 157 | status = "okay"; |
| 158 | label = "LS-UART0"; |
| 159 | }; |
| 160 | /* No optional LS-UART1 on Low Speed Expansion Connector. */ |