blob: 904da1a8acc5036e85d9c66a43d131753b93c04a [file] [log] [blame]
Andy Fleming87e29872015-11-04 15:48:32 -06001/*
2 * Based on corenet_ds.h
3 *
4 * SPDX-License-Identifier: GPL-2.0+
5 */
6
7#ifndef __CONFIG_H
8#define __CONFIG_H
9
Andy Fleming87e29872015-11-04 15:48:32 -060010#define CONFIG_CYRUS
11
York Sun95390362016-11-18 11:39:36 -080012#if !defined(CONFIG_ARCH_P5020) && !defined(CONFIG_ARCH_P5040)
Andy Fleming87e29872015-11-04 15:48:32 -060013#error Must call Cyrus CONFIG with a specific CPU enabled.
14#endif
15
Andy Fleming87e29872015-11-04 15:48:32 -060016#define CONFIG_SDCARD
17#define CONFIG_FSL_SATA_V2
18#define CONFIG_PCIE3
19#define CONFIG_PCIE4
York Suncefe11c2016-11-18 11:30:56 -080020#ifdef CONFIG_ARCH_P5020
Andy Fleming87e29872015-11-04 15:48:32 -060021#define CONFIG_SYS_FSL_RAID_ENGINE
22#define CONFIG_SYS_DPAA_RMAN
23#endif
24#define CONFIG_SYS_DPAA_PME
25
26/*
27 * Corenet DS style board configuration file
28 */
29#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
30#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
31#define CONFIG_SYS_FSL_PBL_PBI board/varisys/cyrus/pbi.cfg
York Suncefe11c2016-11-18 11:30:56 -080032#if defined(CONFIG_ARCH_P5020)
Andy Fleming87e29872015-11-04 15:48:32 -060033#define CONFIG_SYS_CLK_FREQ 133000000
34#define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5020_v2.cfg
York Sun95390362016-11-18 11:39:36 -080035#elif defined(CONFIG_ARCH_P5040)
Andy Fleming87e29872015-11-04 15:48:32 -060036#define CONFIG_SYS_CLK_FREQ 100000000
37#define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5040.cfg
38#endif
39
Andy Fleming87e29872015-11-04 15:48:32 -060040/* High Level Configuration Options */
Andy Fleming87e29872015-11-04 15:48:32 -060041#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
42#define CONFIG_MP /* support multiple processors */
43
Andy Fleming87e29872015-11-04 15:48:32 -060044#define CONFIG_SYS_MMC_MAX_DEVICE 1
45
46#ifndef CONFIG_SYS_TEXT_BASE
47#define CONFIG_SYS_TEXT_BASE 0xeff40000
48#endif
49
50#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
York Sun51370d52016-12-28 08:43:45 -080051#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
Robert P. J. Dayb38eaec2016-05-03 19:52:49 -040052#define CONFIG_PCIE1 /* PCIE controller 1 */
53#define CONFIG_PCIE2 /* PCIE controller 2 */
Andy Fleming87e29872015-11-04 15:48:32 -060054#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
55#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
56
Andy Fleming87e29872015-11-04 15:48:32 -060057#define CONFIG_ENV_OVERWRITE
58
Andy Fleming87e29872015-11-04 15:48:32 -060059#if defined(CONFIG_SDCARD)
60#define CONFIG_SYS_EXTRA_ENV_RELOC
61#define CONFIG_ENV_IS_IN_MMC
62#define CONFIG_FSL_FIXED_MMC_LOCATION
63#define CONFIG_SYS_MMC_ENV_DEV 0
64#define CONFIG_ENV_SIZE 0x2000
65#define CONFIG_ENV_OFFSET (512 * 1658)
66#endif
67
68/*
69 * These can be toggled for performance analysis, otherwise use default.
70 */
71#define CONFIG_SYS_CACHE_STASHING
72#define CONFIG_BACKSIDE_L2_CACHE
73#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
74#define CONFIG_BTB /* toggle branch predition */
75#define CONFIG_DDR_ECC
76#ifdef CONFIG_DDR_ECC
77#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
78#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
79#endif
80
81#define CONFIG_ENABLE_36BIT_PHYS
82
83#ifdef CONFIG_PHYS_64BIT
84#define CONFIG_ADDR_MAP
85#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
86#endif
87
88/* test POST memory test */
89#undef CONFIG_POST
90#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
91#define CONFIG_SYS_MEMTEST_END 0x00400000
92#define CONFIG_SYS_ALT_MEMTEST
93#define CONFIG_PANIC_HANG /* do not reset board on panic */
94
95/*
96 * Config the L3 Cache as L3 SRAM
97 */
98#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
99#ifdef CONFIG_PHYS_64BIT
100#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | CONFIG_RAMBOOT_TEXT_BASE)
101#else
102#define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR
103#endif
104#define CONFIG_SYS_L3_SIZE (1024 << 10)
105#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
106
107#ifdef CONFIG_PHYS_64BIT
108#define CONFIG_SYS_DCSRBAR 0xf0000000
109#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
110#endif
111
112/*
113 * DDR Setup
114 */
115#define CONFIG_VERY_BIG_RAM
116#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
117#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
118
119#define CONFIG_DIMM_SLOTS_PER_CTLR 1
120#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
121
122#define CONFIG_DDR_SPD
Andy Fleming87e29872015-11-04 15:48:32 -0600123
124#define CONFIG_SYS_SPD_BUS_NUM 1
125#define SPD_EEPROM_ADDRESS1 0x51
126#define SPD_EEPROM_ADDRESS2 0x52
127#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
128
129/*
130 * Local Bus Definitions
131 */
132
133#define CONFIG_SYS_LBC0_BASE 0xe0000000 /* Start of LBC Registers */
134#ifdef CONFIG_PHYS_64BIT
135#define CONFIG_SYS_LBC0_BASE_PHYS 0xfe0000000ull
136#else
137#define CONFIG_SYS_LBC0_BASE_PHYS CONFIG_SYS_LBC0_BASE
138#endif
139
140#define CONFIG_SYS_LBC1_BASE 0xe1000000 /* Start of LBC Registers */
141#ifdef CONFIG_PHYS_64BIT
142#define CONFIG_SYS_LBC1_BASE_PHYS 0xfe1000000ull
143#else
144#define CONFIG_SYS_LBC1_BASE_PHYS CONFIG_SYS_LBC1_BASE
145#endif
146
147/* Set the local bus clock 1/16 of platform clock */
148#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_16 | LCRR_EADC_1)
149
150#define CONFIG_SYS_BR0_PRELIM \
151(BR_PHYS_ADDR(CONFIG_SYS_LBC0_BASE_PHYS) | BR_PS_16 | BR_V)
152#define CONFIG_SYS_BR1_PRELIM \
153(BR_PHYS_ADDR(CONFIG_SYS_LBC1_BASE_PHYS) | BR_PS_16 | BR_V)
154
155#define CONFIG_SYS_OR0_PRELIM 0xfff00010
156#define CONFIG_SYS_OR1_PRELIM 0xfff00010
157
Andy Fleming87e29872015-11-04 15:48:32 -0600158#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
159
160#if defined(CONFIG_RAMBOOT_PBL)
161#define CONFIG_SYS_RAMBOOT
162#endif
163
Andy Fleming87e29872015-11-04 15:48:32 -0600164#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
165#define CONFIG_MISC_INIT_R
166
167#define CONFIG_HWCONFIG
168
169/* define to use L1 as initial stack */
170#define CONFIG_L1_INIT_RAM
171#define CONFIG_SYS_INIT_RAM_LOCK
172#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
173#ifdef CONFIG_PHYS_64BIT
174#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
175#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
176/* The assembler doesn't like typecast */
177#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
178 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
179 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
180#else
181#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
182#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
183#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
184#endif
185#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
186
187#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
188#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
189
190#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
191#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
192
193/* Serial Port - controlled on board with jumper J8
194 * open - index 2
195 * shorted - index 1
196 */
197#define CONFIG_CONS_INDEX 1
Andy Fleming87e29872015-11-04 15:48:32 -0600198#define CONFIG_SYS_NS16550_SERIAL
199#define CONFIG_SYS_NS16550_REG_SIZE 1
200#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
201
202#define CONFIG_SYS_BAUDRATE_TABLE \
203{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
204
205#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
206#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
207#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
208#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
209
Andy Fleming87e29872015-11-04 15:48:32 -0600210/* I2C */
211#define CONFIG_SYS_I2C
212#define CONFIG_SYS_I2C_FSL
213#define CONFIG_I2C_MULTI_BUS
214#define CONFIG_I2C_CMD_TREE
215#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed and slave address */
216#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
217#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
218#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed and slave address */
219#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
220#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
221#define CONFIG_SYS_FSL_I2C3_SPEED 400000 /* I2C speed and slave address */
222#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
223#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
224#define CONFIG_SYS_FSL_I2C4_SPEED 400000 /* I2C speed and slave address */
225#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
226#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
227
228#define CONFIG_ID_EEPROM
229#define CONFIG_SYS_I2C_EEPROM_NXID
230#define CONFIG_SYS_EEPROM_BUS_NUM 0
231#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
232#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
233
234#define CONFIG_SYS_I2C_GENERIC_MAC
235#define CONFIG_SYS_I2C_MAC1_BUS 3
236#define CONFIG_SYS_I2C_MAC1_CHIP_ADDR 0x57
237#define CONFIG_SYS_I2C_MAC1_DATA_ADDR 0xf2
238#define CONFIG_SYS_I2C_MAC2_BUS 0
239#define CONFIG_SYS_I2C_MAC2_CHIP_ADDR 0x50
240#define CONFIG_SYS_I2C_MAC2_DATA_ADDR 0xfa
241
Andy Fleming87e29872015-11-04 15:48:32 -0600242#define CONFIG_RTC_MCP79411 1
243#define CONFIG_SYS_RTC_BUS_NUM 3
244#define CONFIG_SYS_I2C_RTC_ADDR 0x6f
245
246/*
247 * eSPI - Enhanced SPI
248 */
Andy Fleming87e29872015-11-04 15:48:32 -0600249
250/*
251 * General PCI
252 * Memory space is mapped 1-1, but I/O space must start from 0.
253 */
254
255/* controller 1, direct to uli, tgtid 3, Base address 20000 */
256#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
257#ifdef CONFIG_PHYS_64BIT
258#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
259#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
260#else
261#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
262#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
263#endif
264#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
265#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
266#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
267#ifdef CONFIG_PHYS_64BIT
268#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
269#else
270#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
271#endif
272#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
273
274/* controller 2, Slot 2, tgtid 2, Base address 201000 */
275#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
276#ifdef CONFIG_PHYS_64BIT
277#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
278#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
279#else
280#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
281#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
282#endif
283#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
284#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
285#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
286#ifdef CONFIG_PHYS_64BIT
287#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
288#else
289#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
290#endif
291#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
292
293/* controller 3, Slot 1, tgtid 1, Base address 202000 */
294#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000
295#ifdef CONFIG_PHYS_64BIT
296#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
297#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
298#else
299#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000
300#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000
301#endif
302#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
303#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
304#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
305#ifdef CONFIG_PHYS_64BIT
306#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
307#else
308#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
309#endif
310#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
311
312/* controller 4, Base address 203000 */
313#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
314#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull
315#define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */
316#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
317#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
318#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
319
320/* Qman/Bman */
321#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
322#define CONFIG_SYS_BMAN_NUM_PORTALS 10
323#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
324#ifdef CONFIG_PHYS_64BIT
325#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
326#else
327#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
328#endif
329#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
330#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
331#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
332#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
333#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
334#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
335 CONFIG_SYS_BMAN_CENA_SIZE)
336#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
337#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
338#define CONFIG_SYS_QMAN_NUM_PORTALS 10
339#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
340#ifdef CONFIG_PHYS_64BIT
341#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
342#else
343#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
344#endif
345#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
346#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
347#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
348#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
349#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
350#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
351 CONFIG_SYS_QMAN_CENA_SIZE)
352#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
353#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
354
355#define CONFIG_SYS_DPAA_FMAN
356/* Default address of microcode for the Linux Fman driver */
357/*
358 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
359 * about 825KB (1650 blocks), Env is stored after the image, and the env size is
360 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
361 */
362#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
363#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
364
365#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
366#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
367
368#ifdef CONFIG_SYS_DPAA_FMAN
369#define CONFIG_FMAN_ENET
370#define CONFIG_PHY_MICREL
371#define CONFIG_PHY_MICREL_KSZ9021
372#endif
373
374#ifdef CONFIG_PCI
375#define CONFIG_PCI_INDIRECT_BRIDGE
Andy Fleming87e29872015-11-04 15:48:32 -0600376#define CONFIG_NET_MULTI
377
378#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
Andy Fleming87e29872015-11-04 15:48:32 -0600379#endif /* CONFIG_PCI */
380
381/* SATA */
382#ifdef CONFIG_FSL_SATA_V2
383#define CONFIG_LIBATA
384#define CONFIG_FSL_SATA
385
386#define CONFIG_SYS_SATA_MAX_DEVICE 2
387#define CONFIG_SATA1
388#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
389#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
390#define CONFIG_SATA2
391#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
392#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
393
394#define CONFIG_LBA48
395#define CONFIG_CMD_SATA
Andy Fleming87e29872015-11-04 15:48:32 -0600396#endif
397
398#ifdef CONFIG_FMAN_ENET
399#define CONFIG_SYS_TBIPA_VALUE 8
400#define CONFIG_MII /* MII PHY management */
401#define CONFIG_ETHPRIME "FM1@DTSEC4"
402#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
403#endif
404
405/*
406 * Environment
407 */
408#define CONFIG_LOADS_ECHO /* echo on for serial download */
409#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
410
411/*
412 * Command line configuration.
413 */
Andy Fleming87e29872015-11-04 15:48:32 -0600414#define CONFIG_CMD_ERRATA
Andy Fleming87e29872015-11-04 15:48:32 -0600415#define CONFIG_CMD_IRQ
Andy Fleming87e29872015-11-04 15:48:32 -0600416#define CONFIG_CMD_REGINFO
417
418#ifdef CONFIG_PCI
419#define CONFIG_CMD_PCI
420#endif
421
422/*
423 * USB
424 */
425#define CONFIG_HAS_FSL_DR_USB
426#define CONFIG_HAS_FSL_MPH_USB
427
428#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
Andy Fleming87e29872015-11-04 15:48:32 -0600429#define CONFIG_USB_EHCI
430#define CONFIG_USB_EHCI_FSL
431#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
Andy Fleming87e29872015-11-04 15:48:32 -0600432#define CONFIG_EHCI_IS_TDI
Andy Fleming87e29872015-11-04 15:48:32 -0600433#define CONFIG_SYS_USB_EVENT_POLL
434 /* _VIA_CONTROL_EP */
Andy Fleming87e29872015-11-04 15:48:32 -0600435#endif
436
437#ifdef CONFIG_MMC
438#define CONFIG_FSL_ESDHC
439#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
440#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
Andy Fleming87e29872015-11-04 15:48:32 -0600441#endif
442
443/*
444 * Miscellaneous configurable options
445 */
446#define CONFIG_SYS_LONGHELP /* undef to save memory */
447#define CONFIG_CMDLINE_EDITING /* Command-line editing */
448#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
449#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
Andy Fleming87e29872015-11-04 15:48:32 -0600450#ifdef CONFIG_CMD_KGDB
451#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
452#else
453#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
454#endif
455#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
456#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
457#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
458
459/*
460 * For booting Linux, the board info and command line data
461 * have to be in the first 64 MB of memory, since this is
462 * the maximum mapped by the Linux kernel during initialization.
463 */
464#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
465#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
466
467#ifdef CONFIG_CMD_KGDB
468#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
469#endif
470
471/*
472 * Environment Configuration
473 */
474#define CONFIG_ROOTPATH "/opt/nfsroot"
475#define CONFIG_BOOTFILE "uImage"
476#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
477
478/* default location for tftp and bootm */
479#define CONFIG_LOADADDR 1000000
480
Andy Fleming87e29872015-11-04 15:48:32 -0600481#define __USB_PHY_TYPE utmi
482
483#define CONFIG_EXTRA_ENV_SETTINGS \
484"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
485"bank_intlv=cs0_cs1;" \
486"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
487"usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
488"netdev=eth0\0" \
489"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
490"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
491"consoledev=ttyS0\0" \
492"ramdiskaddr=2000000\0" \
Scott Woodb24a4f62016-07-19 17:52:06 -0500493"fdtaddr=1e00000\0" \
Andy Fleming87e29872015-11-04 15:48:32 -0600494"bdev=sda3\0"
495
496#define CONFIG_HDBOOT \
497"setenv bootargs root=/dev/$bdev rw " \
498"console=$consoledev,$baudrate $othbootargs;" \
499"tftp $loadaddr $bootfile;" \
500"tftp $fdtaddr $fdtfile;" \
501"bootm $loadaddr - $fdtaddr"
502
503#define CONFIG_NFSBOOTCOMMAND \
504"setenv bootargs root=/dev/nfs rw " \
505"nfsroot=$serverip:$rootpath " \
506"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
507"console=$consoledev,$baudrate $othbootargs;" \
508"tftp $loadaddr $bootfile;" \
509"tftp $fdtaddr $fdtfile;" \
510"bootm $loadaddr - $fdtaddr"
511
512#define CONFIG_RAMBOOTCOMMAND \
513"setenv bootargs root=/dev/ram rw " \
514"console=$consoledev,$baudrate $othbootargs;" \
515"tftp $ramdiskaddr $ramdiskfile;" \
516"tftp $loadaddr $bootfile;" \
517"tftp $fdtaddr $fdtfile;" \
518"bootm $loadaddr $ramdiskaddr $fdtaddr"
519
520#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
521
522#include <asm/fsl_secure_boot.h>
523
524#ifdef CONFIG_SECURE_BOOT
525#endif
526
527#endif /* __CONFIG_H */