blob: 9953df017e1906d461f2bbafb39197960406277e [file] [log] [blame]
Tom Rini83d290c2018-05-06 17:58:06 -04001// SPDX-License-Identifier: GPL-2.0+
Tim Schendekehl14c32612011-11-01 23:55:01 +00002/*
3 * (C) Copyright 2011
4 * egnite GmbH <info@egnite.de>
5 *
6 * (C) Copyright 2010
7 * Ole Reinhardt <ole.reinhardt@thermotemp.de>
Tim Schendekehl14c32612011-11-01 23:55:01 +00008 */
9
10/*
11 * Ethernut 5 general board support
12 *
13 * Ethernut is an open source hardware and software project for
14 * embedded Ethernet devices. Hardware layouts and CAD files are
15 * freely available under BSD-like license.
16 *
17 * Ethernut 5 is the first member of the Ethernut board family
18 * with U-Boot and Linux support. This implementation is based
19 * on the original work done by Ole Reinhardt, but heavily modified
20 * to support additional features and the latest board revision 5.0F.
21 *
22 * Main board components are by default:
23 *
24 * Atmel AT91SAM9XE512 CPU with 512 kBytes NOR Flash
25 * 2 x 64 MBytes Micron MT48LC32M16A2P SDRAM
26 * 512 MBytes Micron MT29F4G08ABADA NAND Flash
27 * 4 MBytes Atmel AT45DB321D DataFlash
28 * SMSC LAN8710 Ethernet PHY
29 * Atmel ATmega168 MCU used for power management
30 * Linear Technology LTC4411 PoE controller
31 *
32 * U-Boot relevant board interfaces are:
33 *
34 * 100 Mbit Ethernet with IEEE 802.3af PoE
35 * RS-232 serial port
36 * USB host and device
37 * MMC/SD-Card slot
38 * Expansion port with I2C, SPI and more...
39 *
40 * Typically the U-Boot image is loaded from serial DataFlash into
41 * SDRAM by the samboot boot loader, which is located in internal
42 * NOR Flash and provides all essential initializations like CPU
43 * and peripheral clocks and, of course, the SDRAM configuration.
44 *
45 * For testing purposes it is also possibly to directly transfer
46 * the image into SDRAM via JTAG. A tested configuration exists
47 * for the Turtelizer 2 hardware dongle and the OpenOCD software.
48 * In this case the latter will do the basic hardware configuration
49 * via its reset-init script.
50 *
51 * For additional information visit the project home page at
52 * http://www.ethernut.de/
53 */
54
55#include <common.h>
Simon Glass9b4a2052019-12-28 10:45:05 -070056#include <init.h>
Tim Schendekehl14c32612011-11-01 23:55:01 +000057#include <net.h>
58#include <netdev.h>
59#include <miiphy.h>
60#include <i2c.h>
Tim Schendekehl14c32612011-11-01 23:55:01 +000061#include <mmc.h>
Andreas Bießmann77c3d842012-03-13 05:01:51 +000062#include <atmel_mci.h>
Simon Glass401d1c42020-10-30 21:38:53 -060063#include <asm/global_data.h>
Tim Schendekehl14c32612011-11-01 23:55:01 +000064
65#include <asm/arch/at91sam9260.h>
66#include <asm/arch/at91sam9260_matrix.h>
67#include <asm/arch/at91sam9_smc.h>
68#include <asm/arch/at91_common.h>
Wenyou Yang70341e22016-02-03 10:16:50 +080069#include <asm/arch/clk.h>
Tim Schendekehl14c32612011-11-01 23:55:01 +000070#include <asm/arch/gpio.h>
71#include <asm/io.h>
Andreas Bießmannac45bb12013-11-29 12:13:45 +010072#include <asm/gpio.h>
Tim Schendekehl14c32612011-11-01 23:55:01 +000073
74#include "ethernut5_pwrman.h"
75
76DECLARE_GLOBAL_DATA_PTR;
77
Tim Schendekehl14c32612011-11-01 23:55:01 +000078/*
79 * This is called last during early initialization. Most of the basic
80 * hardware interfaces are up and running.
81 *
82 * The SDRAM hardware has been configured by the first stage boot loader.
83 * We only need to announce its size, using u-boot's memory check.
84 */
85int dram_init(void)
86{
87 gd->ram_size = get_ram_size(
Tom Riniaa6e94d2022-11-16 13:10:37 -050088 (void *)CFG_SYS_SDRAM_BASE,
89 CFG_SYS_SDRAM_SIZE);
Tim Schendekehl14c32612011-11-01 23:55:01 +000090 return 0;
91}
92
93#ifdef CONFIG_CMD_NAND
94static void ethernut5_nand_hw_init(void)
95{
96 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
97 struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
98 unsigned long csa;
99
100 /* Assign CS3 to NAND/SmartMedia Interface */
101 csa = readl(&matrix->ebicsa);
102 csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
103 writel(csa, &matrix->ebicsa);
104
105 /* Configure SMC CS3 for NAND/SmartMedia */
106 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
107 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
108 &smc->cs[3].setup);
109 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
110 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
111 &smc->cs[3].pulse);
112 writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
113 &smc->cs[3].cycle);
114 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
115 AT91_SMC_MODE_EXNW_DISABLE |
116 AT91_SMC_MODE_DBW_8 |
117 AT91_SMC_MODE_TDF_CYCLE(2),
118 &smc->cs[3].mode);
119
Tom Rini4e590942022-11-12 17:36:51 -0500120#ifdef CFG_SYS_NAND_READY_PIN
Tim Schendekehl14c32612011-11-01 23:55:01 +0000121 /* Ready pin is optional. */
Tom Rini4e590942022-11-12 17:36:51 -0500122 at91_set_pio_input(CFG_SYS_NAND_READY_PIN, 1);
Tim Schendekehl14c32612011-11-01 23:55:01 +0000123#endif
Tom Rini4e590942022-11-12 17:36:51 -0500124 gpio_direction_output(CFG_SYS_NAND_ENABLE_PIN, 1);
Tim Schendekehl14c32612011-11-01 23:55:01 +0000125}
126#endif
127
128/*
129 * This is called first during late initialization.
130 */
131int board_init(void)
132{
Wenyou Yang70341e22016-02-03 10:16:50 +0800133 at91_periph_clk_enable(ATMEL_ID_PIOA);
134 at91_periph_clk_enable(ATMEL_ID_PIOB);
135 at91_periph_clk_enable(ATMEL_ID_PIOC);
Tim Schendekehl14c32612011-11-01 23:55:01 +0000136
Tim Schendekehl14c32612011-11-01 23:55:01 +0000137 /* Set adress of boot parameters. */
Tom Riniaa6e94d2022-11-16 13:10:37 -0500138 gd->bd->bi_boot_params = CFG_SYS_SDRAM_BASE + 0x100;
Tim Schendekehl14c32612011-11-01 23:55:01 +0000139 /* Initialize UARTs and power management. */
Tim Schendekehl14c32612011-11-01 23:55:01 +0000140 ethernut5_power_init();
141#ifdef CONFIG_CMD_NAND
142 ethernut5_nand_hw_init();
143#endif
Tim Schendekehl14c32612011-11-01 23:55:01 +0000144 return 0;
145}
146
147#ifdef CONFIG_MACB
148/*
149 * This is optionally called last during late initialization.
150 */
Masahiro Yamadab75d8dc2020-06-26 15:13:33 +0900151int board_eth_init(struct bd_info *bis)
Tim Schendekehl14c32612011-11-01 23:55:01 +0000152{
153 const char *devname;
154 unsigned short mode;
Tim Schendekehl14c32612011-11-01 23:55:01 +0000155
Wenyou Yang70341e22016-02-03 10:16:50 +0800156 at91_periph_clk_enable(ATMEL_ID_EMAC0);
157
Tim Schendekehl14c32612011-11-01 23:55:01 +0000158 /* Need to reset PHY via power management. */
159 ethernut5_phy_reset();
160 /* Set peripheral pins. */
161 at91_macb_hw_init();
162 /* Basic EMAC initialization. */
Tom Rini52d596e2022-12-04 10:13:28 -0500163 if (macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, CFG_PHY_ID))
Tim Schendekehl14c32612011-11-01 23:55:01 +0000164 return -1;
165 /*
166 * Early board revisions have a pull-down at the PHY's MODE0
167 * strap pin, which forces the PHY into power down. Here we
168 * switch to all-capable mode.
169 */
170 devname = miiphy_get_current_dev();
171 if (miiphy_read(devname, 0, 18, &mode) == 0) {
172 /* Set mode[2:0] to 0b111. */
173 mode |= 0x00E0;
174 miiphy_write(devname, 0, 18, mode);
175 /* Soft reset overrides strap pins. */
176 miiphy_write(devname, 0, MII_BMCR, BMCR_RESET);
177 }
178 /* Sync environment with network devices, needed for nfsroot. */
Joe Hershbergerd2eaec62015-03-22 17:09:06 -0500179 return eth_init();
Tim Schendekehl14c32612011-11-01 23:55:01 +0000180}
181#endif
182
183#ifdef CONFIG_GENERIC_ATMEL_MCI
Masahiro Yamadab75d8dc2020-06-26 15:13:33 +0900184int board_mmc_init(struct bd_info *bd)
Tim Schendekehl14c32612011-11-01 23:55:01 +0000185{
Wenyou Yang70341e22016-02-03 10:16:50 +0800186 at91_periph_clk_enable(ATMEL_ID_MCI);
Tim Schendekehl14c32612011-11-01 23:55:01 +0000187
Tim Schendekehl14c32612011-11-01 23:55:01 +0000188 /* Initialize MCI hardware. */
189 at91_mci_hw_init();
190 /* Register the device. */
191 return atmel_mci_init((void *)ATMEL_BASE_MCI);
192}
193
prabhakar.csengg@gmail.com2271e7c2012-02-23 01:53:40 +0000194int board_mmc_getcd(struct mmc *mmc)
Tim Schendekehl14c32612011-11-01 23:55:01 +0000195{
Tom Rini65cc0e22022-11-16 13:10:41 -0500196 return !at91_get_pio_value(CFG_SYS_MMC_CD_PIN);
Tim Schendekehl14c32612011-11-01 23:55:01 +0000197}
198#endif