blob: 18fe277cada77b585012af8d5c0279ea834a7d0e [file] [log] [blame]
Masahiro Yamada5894ca02014-10-03 19:21:06 +09001/*
2 * Copyright (C) 2012-2014 Panasonic Corporation
3 * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
4 *
5 * SPDX-License-Identifier: GPL-2.0+
6 */
7
8/* U-boot - Common settings for UniPhier Family */
9
10#ifndef __CONFIG_UNIPHIER_COMMON_H__
11#define __CONFIG_UNIPHIER_COMMON_H__
12
13#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD) && \
14 defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
15# error "Both CONFIG_PFC_MICRO_SUPPORT_CARD and CONFIG_DCC_MICRO_SUPPORT_CARD \
16are defined. Select only one of them."
17#endif
18
19/*
20 * Support card address map
21 */
22#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
23# define CONFIG_SUPPORT_CARD_BASE 0x03f00000
24# define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
25# define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00090000)
26# define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x000b0000)
27#endif
28
29#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
30# define CONFIG_SUPPORT_CARD_BASE 0x08000000
31# define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
32# define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00401630)
33# define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00200000)
34#endif
35
36#define CONFIG_SYS_NS16550
37#define CONFIG_SYS_NS16550_COM1 CONFIG_SUPPORT_CARD_UART_BASE
38#define CONFIG_SYS_NS16550_CLK 12288000
39#define CONFIG_SYS_NS16550_REG_SIZE -2
40
41#define CONFIG_SMC911X_BASE CONFIG_SUPPORT_CARD_ETHER_BASE
42#define CONFIG_SMC911X_32_BIT
43
44#define CONFIG_SYS_UNIPHIER_SERIAL_BASE0 0x54006800
45#define CONFIG_SYS_UNIPHIER_SERIAL_BASE1 0x54006900
46#define CONFIG_SYS_UNIPHIER_SERIAL_BASE2 0x54006a00
47#define CONFIG_SYS_UNIPHIER_SERIAL_BASE3 0x54006b00
48
49/*-----------------------------------------------------------------------
50 * MMU and Cache Setting
51 *----------------------------------------------------------------------*/
52
53/* Comment out the following to enable L1 cache */
54/* #define CONFIG_SYS_ICACHE_OFF */
55/* #define CONFIG_SYS_DCACHE_OFF */
56
57/* Comment out the following to enable L2 cache */
58#define CONFIG_UNIPHIER_L2CACHE_ON
59
60#define CONFIG_DISPLAY_CPUINFO
61#define CONFIG_DISPLAY_BOARDINFO
62#define CONFIG_BOARD_LATE_INIT
63
64#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
65
66#define CONFIG_TIMESTAMP
67
68/* FLASH related */
69#define CONFIG_MTD_DEVICE
70
71/*
72 * uncomment the following to disable FLASH related code.
73 */
74/* #define CONFIG_SYS_NO_FLASH */
75
76#define CONFIG_FLASH_CFI_DRIVER
77#define CONFIG_SYS_FLASH_CFI
78
79#define CONFIG_SYS_MAX_FLASH_SECT 256
80#define CONFIG_SYS_MONITOR_BASE 0
81#define CONFIG_SYS_FLASH_BASE 0
82
83/*
84 * flash_toggle does not work for out supoort card.
85 * We need to use flash_status_poll.
86 */
87#define CONFIG_SYS_CFI_FLASH_STATUS_POLL
88
89#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
90
91#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
92# define CONFIG_SYS_MAX_FLASH_BANKS 1
93# define CONFIG_SYS_FLASH_BANKS_LIST {0x00000000}
94# define CONFIG_SYS_FLASH_BANKS_SIZES {0x02000000}
95#endif
96
97#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
98# define CONFIG_SYS_MAX_FLASH_BANKS 1
99# define CONFIG_SYS_FLASH_BANKS_LIST {0x04000000}
100# define CONFIG_SYS_FLASH_BANKS_SIZES {0x04000000}
101#endif
102
103/* serial console configuration */
104#define CONFIG_BAUDRATE 115200
105
106#define CONFIG_SYS_GENERIC_BOARD
107
108#if !defined(CONFIG_SPL_BUILD)
109#define CONFIG_USE_ARCH_MEMSET
110#define CONFIG_USE_ARCH_MEMCPY
111#endif
112
113#define CONFIG_SYS_LONGHELP /* undef to save memory */
114
115#define CONFIG_CMDLINE_EDITING /* add command line history */
116#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
117#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
118/* Print Buffer Size */
119#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
120#define CONFIG_SYS_MAXARGS 16 /* max number of command */
121/* Boot Argument Buffer Size */
122#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
123
124#define CONFIG_CONS_INDEX 1
125
126/*
127 * For NAND booting the environment is embedded in the U-Boot image. Please take
128 * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
129 */
130/* #define CONFIG_ENV_IS_IN_NAND */
131#define CONFIG_ENV_IS_NOWHERE
132#define CONFIG_ENV_SIZE 0x2000
133#define CONFIG_ENV_OFFSET 0x0
134/* #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
135
136/* Time clock 1MHz */
137#define CONFIG_SYS_TIMER_RATE 1000000
138
139/*
140 * By default, ARP timeout is 5 sec.
141 * The first ARP request does not seem to work.
142 * So we need to retry ARP request anyway.
143 * We want to shrink the interval until the second ARP request.
144 */
145#define CONFIG_ARP_TIMEOUT 500UL /* 0.5 msec */
146
147/*
148 * Command line configuration.
149 */
150#include <config_cmd_default.h>
151
152#define CONFIG_CMD_PING
153#define CONFIG_CMD_TIME
154#define CONFIG_CMD_NAND /* NAND flash suppport */
155
156#define CONFIG_SYS_MAX_NAND_DEVICE 1
157#define CONFIG_SYS_NAND_MAX_CHIPS 2
158#define CONFIG_SYS_NAND_ONFI_DETECTION
159
160#define CONFIG_NAND_DENALI_ECC_SIZE 1024
161
162#define CONFIG_SYS_NAND_REGS_BASE 0x68100000
163#define CONFIG_SYS_NAND_DATA_BASE 0x68000000
164
165#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_DATA_BASE + 0x10)
166
167#define CONFIG_SYS_NAND_USE_FLASH_BBT
168#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
169
170/* memtest works on */
171#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
172#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01000000)
173
174#define CONFIG_BOOTDELAY 3
175#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
176#define CONFIG_AUTOBOOT_KEYED 1
177#define CONFIG_AUTOBOOT_PROMPT \
178 "Press SPACE to abort autoboot in %d seconds\n", bootdelay
179#define CONFIG_AUTOBOOT_DELAY_STR "d"
180#define CONFIG_AUTOBOOT_STOP_STR " "
181
182/*
183 * Network Configuration
184 */
185#define CONFIG_ETHADDR 00:21:83:24:00:00
186#define CONFIG_SERVERIP 192.168.11.1
187#define CONFIG_IPADDR 192.168.11.10
188#define CONFIG_GATEWAYIP 192.168.11.1
189#define CONFIG_NETMASK 255.255.255.0
190
191#define CONFIG_LOADADDR 0x84000000
192#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
193#define CONFIG_BOOTFILE "fit.itb"
194
195#define CONFIG_CMDLINE_EDITING /* add command line history */
196
197#define CONFIG_BOOTCOMMAND "run $bootmode"
198
199#define CONFIG_ROOTPATH "/nfs/root/path"
200#define CONFIG_NFSBOOTCOMMAND \
201 "setenv bootargs $bootargs root=/dev/nfs rw " \
202 "nfsroot=$serverip:$rootpath " \
203 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
204 "tftpboot; bootm;"
205
206#define CONFIG_BOOTARGS " user_debug=0x1f init=/sbin/init"
207
208#define CONFIG_EXTRA_ENV_SETTINGS \
209 "netdev=eth0\0" \
210 "image_offset=0x00080000\0" \
211 "image_size=0x00f00000\0" \
212 "verify=n\0" \
213 "autostart=yes\0" \
214 "norboot=run add_default_bootargs;" \
215 "bootm $image_offset\0" \
216 "nandboot=run add_default_bootargs;" \
217 "nand read $loadaddr $image_offset $image_size;" \
218 "bootm\0" \
219 "add_default_bootargs=setenv bootargs $bootargs" \
220 " console=ttyS0,$baudrate\0" \
221
222/* FIT support */
223#define CONFIG_FIT
224#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
225
226/* Open Firmware flat tree */
227#define CONFIG_OF_LIBFDT
228
229#define CONFIG_HAVE_ARM_SECURE
230
231/* Memory Size & Mapping */
232#define CONFIG_SYS_SDRAM_BASE CONFIG_SDRAM0_BASE
233
234#if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE
235/* Thre is no memory hole */
236#define CONFIG_NR_DRAM_BANKS 1
237#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE)
238#else
239#define CONFIG_NR_DRAM_BANKS 2
240#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE)
241#endif
242
243#define CONFIG_SYS_TEXT_BASE 0x84000000
244
245#if defined(CONFIG_SPL_BUILD)
246#define CONFIG_BOARD_POSTCLK_INIT
247#else
248#define CONFIG_SKIP_LOWLEVEL_INIT
249#endif
250
251#define CONFIG_SYS_SPL_MALLOC_START (0x0ff00000)
252#define CONFIG_SYS_SPL_MALLOC_SIZE (0x00004000)
253
254#define CONFIG_SYS_INIT_SP_ADDR (0x0ff08000)
255
256#define CONFIG_SPL_FRAMEWORK
257#define CONFIG_SPL_NAND_SUPPORT
258
259#define CONFIG_SPL_LIBCOMMON_SUPPORT /* for mem_malloc_init */
260#define CONFIG_SPL_LIBGENERIC_SUPPORT
261
262#define CONFIG_SPL_BOARD_INIT
263
264#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x10000
265
266#endif /* __CONFIG_UNIPHIER_COMMON_H__ */