blob: 17aab5a7bbf0f57c014564eb4f37b5f4dd13d018 [file] [log] [blame]
John Schmollerbfe18812010-10-22 00:20:34 -05001/*
2 * Copyright 2010 Extreme Engineering Solutions, Inc.
3 * Copyright 2007-2008 Freescale Semiconductor, Inc.
4 *
5 * See file CREDITS for list of people who contributed to this
6 * project.
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License as
10 * published by the Free Software Foundation; either version 2 of
11 * the License, or (at your option) any later version.
12 * This program is distributed in the hope that it will be useful,
13 * but WITHOUT ANY WARRANTY; without even the implied warranty of
14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
15 * GNU General Public License for more details.
16 *
17 * You should have received a copy of the GNU General Public License
18 * along with this program; if not, write to the Free Software
19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
20 * MA 02111-1307 USA
21 */
22
23/*
24 * xpedite550x board configuration file
25 */
26#ifndef __CONFIG_H
27#define __CONFIG_H
28
29/*
30 * High Level Configuration Options
31 */
32#define CONFIG_BOOKE 1 /* BOOKE */
33#define CONFIG_E500 1 /* BOOKE e500 family */
34#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
35#define CONFIG_P2020 1
36#define CONFIG_XPEDITE550X 1
37#define CONFIG_SYS_BOARD_NAME "XPedite5500"
38#define CONFIG_SYS_FORM_PMC_XMC 1
39#define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */
40#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
41
42#ifndef CONFIG_SYS_TEXT_BASE
43#define CONFIG_SYS_TEXT_BASE 0xfff80000
44#endif
45
46#define CONFIG_PCI 1 /* Enable PCI/PCIE */
47#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
48#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
49#define CONFIG_PCIE1 1 /* PCIE controler 1 (PEX8112 or XMC) */
50#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
51#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
52#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
53#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
54#define CONFIG_FSL_ELBC 1
55
56/*
57 * Multicore config
58 */
59#define CONFIG_MP
60#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */
61#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */
62
63/*
64 * DDR config
65 */
66#define CONFIG_FSL_DDR3
67#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
68#define CONFIG_DDR_SPD
69#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
Kumar Galac39f44d2011-01-31 22:18:47 -060070#define SPD_EEPROM_ADDRESS 0x54
John Schmollerbfe18812010-10-22 00:20:34 -050071#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
72#define CONFIG_NUM_DDR_CONTROLLERS 1
73#define CONFIG_DIMM_SLOTS_PER_CTLR 1
74#define CONFIG_CHIP_SELECTS_PER_CTRL 2
75#define CONFIG_DDR_ECC
76#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
77#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
78#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
79#define CONFIG_VERY_BIG_RAM
80
81#ifndef __ASSEMBLY__
82extern unsigned long get_board_sys_clk(unsigned long dummy);
83extern unsigned long get_board_ddr_clk(unsigned long dummy);
84#endif
85
86#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
87#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
88
89/*
90 * These can be toggled for performance analysis, otherwise use default.
91 */
92#define CONFIG_L2_CACHE /* toggle L2 cache */
93#define CONFIG_BTB /* toggle branch predition */
94#define CONFIG_ENABLE_36BIT_PHYS 1
95
96/*
97 * Base addresses -- Note these are effective addresses where the
98 * actual resources get mapped (not physical addresses)
99 */
100#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
101#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */
102#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
103#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
104
105/*
106 * Diagnostics
107 */
108#define CONFIG_SYS_ALT_MEMTEST
109#define CONFIG_SYS_MEMTEST_START 0x10000000
110#define CONFIG_SYS_MEMTEST_END 0x20000000
111#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
112 CONFIG_SYS_POST_I2C)
113#define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \
114 CONFIG_SYS_I2C_LM75_ADDR, \
115 CONFIG_SYS_I2C_LM90_ADDR, \
116 CONFIG_SYS_I2C_PCA953X_ADDR0, \
117 CONFIG_SYS_I2C_PCA953X_ADDR2, \
118 CONFIG_SYS_I2C_PCA953X_ADDR3, \
119 CONFIG_SYS_I2C_RTC_ADDR}
120
121/*
122 * Memory map
123 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
124 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
125 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
126 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
127 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable
128 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
129 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
130 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
131 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
132 */
133
134#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3)
135
136/*
137 * NAND flash configuration
138 */
139#define CONFIG_SYS_NAND_BASE 0xef800000
140#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
141#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \
142 CONFIG_SYS_NAND_BASE2}
143#define CONFIG_SYS_MAX_NAND_DEVICE 2
144#define CONFIG_MTD_NAND_VERIFY_WRITE
145#define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */
146#define CONFIG_NAND_FSL_ELBC
147
148/*
149 * NOR flash configuration
150 */
151#define CONFIG_SYS_FLASH_BASE 0xf8000000
152#define CONFIG_SYS_FLASH_BASE2 0xf0000000
153#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
154#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
155#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
156#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
157#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
158#define CONFIG_FLASH_CFI_DRIVER
159#define CONFIG_SYS_FLASH_CFI
160#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
161#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
162 {0xf7f40000, 0xc0000} }
163#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
164
165/*
166 * Chip select configuration
167 */
168/* NOR Flash 0 on CS0 */
169#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
170 BR_PS_16 | \
171 BR_V)
172#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \
173 OR_GPCM_CSNT | \
174 OR_GPCM_XACS | \
175 OR_GPCM_ACS_DIV2 | \
176 OR_GPCM_SCY_8 | \
177 OR_GPCM_TRLX | \
178 OR_GPCM_EHTR | \
179 OR_GPCM_EAD)
180
181/* NOR Flash 1 on CS1 */
182#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \
183 BR_PS_16 | \
184 BR_V)
185#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
186
187/* NAND flash on CS2 */
188#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \
189 (2<<BR_DECC_SHIFT) | \
190 BR_PS_8 | \
191 BR_MS_FCM | \
192 BR_V)
193
194/* NAND flash on CS2 */
195#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \
196 OR_FCM_PGS | \
197 OR_FCM_CSCT | \
198 OR_FCM_CST | \
199 OR_FCM_CHT | \
200 OR_FCM_SCY_1 | \
201 OR_FCM_TRLX | \
202 OR_FCM_EHTR)
203
204/* NAND flash on CS3 */
205#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \
206 (2<<BR_DECC_SHIFT) | \
207 BR_PS_8 | \
208 BR_MS_FCM | \
209 BR_V)
210#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
211
212/*
213 * Use L1 as initial stack
214 */
215#define CONFIG_SYS_INIT_RAM_LOCK 1
216#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
Wolfgang Denk553f0982010-10-26 13:32:32 +0200217#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
John Schmollerbfe18812010-10-22 00:20:34 -0500218
Wolfgang Denk25ddd1f2010-10-26 14:34:52 +0200219#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
John Schmollerbfe18812010-10-22 00:20:34 -0500220#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
221
222#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
223#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
224
225/*
226 * Serial Port
227 */
228#define CONFIG_CONS_INDEX 1
229#define CONFIG_SYS_NS16550
230#define CONFIG_SYS_NS16550_SERIAL
231#define CONFIG_SYS_NS16550_REG_SIZE 1
232#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
233#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
234#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
235#define CONFIG_SYS_BAUDRATE_TABLE \
236 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
237#define CONFIG_BAUDRATE 115200
238#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
239#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
240
241/*
242 * Use the HUSH parser
243 */
244#define CONFIG_SYS_HUSH_PARSER
245#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
246
247/*
248 * Pass open firmware flat tree
249 */
250#define CONFIG_OF_LIBFDT 1
251#define CONFIG_OF_BOARD_SETUP 1
252#define CONFIG_OF_STDOUT_VIA_ALIAS 1
253#define CONFIG_FDT_FIXUP_PCI_IRQ 1
254
255/*
256 * I2C
257 */
258#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
259#define CONFIG_HARD_I2C /* I2C with hardware support */
260#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
261#define CONFIG_SYS_I2C_SLAVE 0x7F
262#define CONFIG_SYS_I2C_OFFSET 0x3000
263#define CONFIG_SYS_I2C2_OFFSET 0x3100
264#define CONFIG_I2C_MULTI_BUS
265
266/* I2C DS7505 temperature sensor */
267#define CONFIG_DTT_LM75
268#define CONFIG_DTT_SENSORS { 0 }
269#define CONFIG_SYS_I2C_LM75_ADDR 0x48
270
271/* I2C ADT7461 temperature sensor */
272#define CONFIG_SYS_I2C_LM90_ADDR 0x4C
273
274/* I2C EEPROM - AT24C128B */
275#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
276#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
277#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
278#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
279
280/* I2C RTC */
281#define CONFIG_RTC_M41T11 1
282#define CONFIG_SYS_I2C_RTC_ADDR 0x68
283#define CONFIG_SYS_M41T11_BASE_YEAR 2000
284
285/* GPIO */
286#define CONFIG_PCA953X
287#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
288#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
289#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
290#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
291#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
292
293/*
294 * GPIO pin definitions, PU = pulled high, PD = pulled low
295 */
296/* PCA9557 @ 0x18*/
297#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
298#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */
299#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
300#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */
301#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
302#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */
303
304/* PCA9557 @ 0x1e*/
305#define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */
306#define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */
307#define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */
308#define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */
309#define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */
310#define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */
311#define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */
312
313/* PCA9557 @ 0x1f */
314#define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */
315#define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */
316#define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */
317#define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */
318#define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */
319#define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */
320#define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */
321#define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */
322
323/*
324 * General PCI
325 * Memory space is mapped 1-1, but I/O space must start from 0.
326 */
327
328/* controller 1 - PEX8112 or XMC, depending on build option */
329#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
330#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
331#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
332#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
333#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
334#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
335
336
337/*
338 * Networking options
339 */
340#define CONFIG_TSEC_ENET /* tsec ethernet support */
341#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
342#define CONFIG_NET_MULTI 1
343#define CONFIG_TSEC_TBI
344#define CONFIG_MII 1 /* MII PHY management */
345#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
346#define CONFIG_ETHPRIME "eTSEC2"
347
Kumar Gala72c96a62010-12-01 22:55:54 -0600348/*
349 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
350 * 1000mbps SGMII link
351 */
352#define CONFIG_TSEC_TBICR_SETTINGS ( \
353 TBICR_PHY_RESET \
354 | TBICR_FULL_DUPLEX \
355 | TBICR_SPEED1_SET \
356 )
357
John Schmollerbfe18812010-10-22 00:20:34 -0500358#define CONFIG_TSEC1 1
359#define CONFIG_TSEC1_NAME "eTSEC1"
360#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
361#define TSEC1_PHY_ADDR 1
362#define TSEC1_PHYIDX 0
363#define CONFIG_HAS_ETH0
364
365#define CONFIG_TSEC2 1
366#define CONFIG_TSEC2_NAME "eTSEC2"
367#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
368#define TSEC2_PHY_ADDR 2
369#define TSEC2_PHYIDX 0
370#define CONFIG_HAS_ETH1
371
372#define CONFIG_TSEC3 1
373#define CONFIG_TSEC3_NAME "eTSEC3"
374#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
375#define TSEC3_PHY_ADDR 3
376#define TSEC3_PHYIDX 0
377#define CONFIG_HAS_ETH2
378
379/*
380 * USB
381 */
382#define CONFIG_USB_STORAGE
383#define CONFIG_USB_EHCI
384#define CONFIG_USB_EHCI_FSL
385#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
386#define CONFIG_DOS_PARTITION
387
388/*
389 * Command configuration.
390 */
391#include <config_cmd_default.h>
392
393#define CONFIG_CMD_ASKENV
394#define CONFIG_CMD_DATE
395#define CONFIG_CMD_DHCP
396#define CONFIG_CMD_DTT
397#define CONFIG_CMD_EEPROM
398#define CONFIG_CMD_ELF
399#define CONFIG_CMD_FLASH
400#define CONFIG_CMD_I2C
401#define CONFIG_CMD_JFFS2
402#define CONFIG_CMD_MII
403#define CONFIG_CMD_NAND
404#define CONFIG_CMD_NET
405#define CONFIG_CMD_PCA953X
406#define CONFIG_CMD_PCA953X_INFO
407#define CONFIG_CMD_PCI
408#define CONFIG_CMD_PCI_ENUM
409#define CONFIG_CMD_PING
410#define CONFIG_CMD_REGINFO
411#define CONFIG_CMD_SAVEENV
412#define CONFIG_CMD_SNTP
413#define CONFIG_CMD_USB
414
415/*
416 * Miscellaneous configurable options
417 */
418#define CONFIG_SYS_LONGHELP /* undef to save memory */
419#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
420#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
421#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
422#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
423#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
424#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
425#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
426#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
427#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
428#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
429#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */
430#define CONFIG_PANIC_HANG /* do not reset board on panic */
431#define CONFIG_PREBOOT /* enable preboot variable */
432#define CONFIG_FIT 1
433#define CONFIG_FIT_VERBOSE 1
434#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
435
436/*
437 * For booting Linux, the board info and command line data
438 * have to be in the first 16 MB of memory, since this is
439 * the maximum mapped by the Linux kernel during initialization.
440 */
441#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
442#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
443
444/*
445 * Boot Flags
446 */
447#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
448#define BOOTFLAG_WARM 0x02 /* Software reboot */
449
450/*
451 * Environment Configuration
452 */
453#define CONFIG_ENV_IS_IN_FLASH 1
454#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
455#define CONFIG_ENV_SIZE 0x8000
456#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
457
458/*
459 * Flash memory map:
460 * fff80000 - ffffffff Pri U-Boot (512 KB)
461 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
462 * fff00000 - fff3ffff Pri FDT (256KB)
463 * fef00000 - ffefffff Pri OS image (16MB)
464 * f8000000 - feefffff Pri OS Use/Filesystem (111MB)
465 *
466 * f7f80000 - f7ffffff Sec U-Boot (512 KB)
467 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB)
468 * f7f00000 - f7f3ffff Sec FDT (256KB)
469 * f6f00000 - f7efffff Sec OS image (16MB)
470 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
471 */
472#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000)
473#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f80000)
474#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000)
475#define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7f00000)
476#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000)
477#define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000)
478
479#define CONFIG_PROG_UBOOT1 \
480 "$download_cmd $loadaddr $ubootfile; " \
481 "if test $? -eq 0; then " \
482 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
483 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
484 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
485 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
486 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
487 "if test $? -ne 0; then " \
488 "echo PROGRAM FAILED; " \
489 "else; " \
490 "echo PROGRAM SUCCEEDED; " \
491 "fi; " \
492 "else; " \
493 "echo DOWNLOAD FAILED; " \
494 "fi;"
495
496#define CONFIG_PROG_UBOOT2 \
497 "$download_cmd $loadaddr $ubootfile; " \
498 "if test $? -eq 0; then " \
499 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
500 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
501 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
502 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
503 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
504 "if test $? -ne 0; then " \
505 "echo PROGRAM FAILED; " \
506 "else; " \
507 "echo PROGRAM SUCCEEDED; " \
508 "fi; " \
509 "else; " \
510 "echo DOWNLOAD FAILED; " \
511 "fi;"
512
513#define CONFIG_BOOT_OS_NET \
514 "$download_cmd $osaddr $osfile; " \
515 "if test $? -eq 0; then " \
516 "if test -n $fdtaddr; then " \
517 "$download_cmd $fdtaddr $fdtfile; " \
518 "if test $? -eq 0; then " \
519 "bootm $osaddr - $fdtaddr; " \
520 "else; " \
521 "echo FDT DOWNLOAD FAILED; " \
522 "fi; " \
523 "else; " \
524 "bootm $osaddr; " \
525 "fi; " \
526 "else; " \
527 "echo OS DOWNLOAD FAILED; " \
528 "fi;"
529
530#define CONFIG_PROG_OS1 \
531 "$download_cmd $osaddr $osfile; " \
532 "if test $? -eq 0; then " \
533 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
534 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
535 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
536 "if test $? -ne 0; then " \
537 "echo OS PROGRAM FAILED; " \
538 "else; " \
539 "echo OS PROGRAM SUCCEEDED; " \
540 "fi; " \
541 "else; " \
542 "echo OS DOWNLOAD FAILED; " \
543 "fi;"
544
545#define CONFIG_PROG_OS2 \
546 "$download_cmd $osaddr $osfile; " \
547 "if test $? -eq 0; then " \
548 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
549 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
550 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
551 "if test $? -ne 0; then " \
552 "echo OS PROGRAM FAILED; " \
553 "else; " \
554 "echo OS PROGRAM SUCCEEDED; " \
555 "fi; " \
556 "else; " \
557 "echo OS DOWNLOAD FAILED; " \
558 "fi;"
559
560#define CONFIG_PROG_FDT1 \
561 "$download_cmd $fdtaddr $fdtfile; " \
562 "if test $? -eq 0; then " \
563 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
564 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
565 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
566 "if test $? -ne 0; then " \
567 "echo FDT PROGRAM FAILED; " \
568 "else; " \
569 "echo FDT PROGRAM SUCCEEDED; " \
570 "fi; " \
571 "else; " \
572 "echo FDT DOWNLOAD FAILED; " \
573 "fi;"
574
575#define CONFIG_PROG_FDT2 \
576 "$download_cmd $fdtaddr $fdtfile; " \
577 "if test $? -eq 0; then " \
578 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
579 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
580 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
581 "if test $? -ne 0; then " \
582 "echo FDT PROGRAM FAILED; " \
583 "else; " \
584 "echo FDT PROGRAM SUCCEEDED; " \
585 "fi; " \
586 "else; " \
587 "echo FDT DOWNLOAD FAILED; " \
588 "fi;"
589
590#define CONFIG_EXTRA_ENV_SETTINGS \
591 "autoload=yes\0" \
592 "download_cmd=tftp\0" \
593 "console_args=console=ttyS0,115200\0" \
594 "root_args=root=/dev/nfs rw\0" \
595 "misc_args=ip=on\0" \
596 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
597 "bootfile=/home/user/file\0" \
598 "osfile=/home/user/board.uImage\0" \
599 "fdtfile=/home/user/board.dtb\0" \
600 "ubootfile=/home/user/u-boot.bin\0" \
601 "fdtaddr=c00000\0" \
602 "osaddr=0x1000000\0" \
603 "loadaddr=0x1000000\0" \
604 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
605 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
606 "prog_os1="CONFIG_PROG_OS1"\0" \
607 "prog_os2="CONFIG_PROG_OS2"\0" \
608 "prog_fdt1="CONFIG_PROG_FDT1"\0" \
609 "prog_fdt2="CONFIG_PROG_FDT2"\0" \
610 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
611 "bootcmd_flash1=run set_bootargs; " \
612 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
613 "bootcmd_flash2=run set_bootargs; " \
614 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
615 "bootcmd=run bootcmd_flash1\0"
616#endif /* __CONFIG_H */