blob: 9b5539fff33e00bc89b6592b7b044233e12c0f3f [file] [log] [blame]
Mingkai Hu4f1d1b72011-07-07 12:29:15 +08001Overview
2=========
3The P2041 Processor combines four Power Architecture processor cores
4with high-performance datapath acceleration architecture(DPAA), CoreNet
5fabric infrastructure, as well as network and peripheral bus interfaces
6required for networking, telecom/datacom, wireless infrastructure, and
7military/aerospace applications.
8
9P2041RDB board is a quad core platform supporting the P2041 processor
10of QorIQ DPAA series.
11
12Boot from NOR flash
13===================
141. Build image
15 make P2041RDB_config
16 make all
17
182. Program image
19 => tftp 1000000 u-boot.bin
20 => protect off all
Prabhakar Kushwahae222b1f2014-01-14 11:34:26 +053021 => erase eff40000 efffffff
22 => cp.b 1000000 eff40000 c0000
Mingkai Hu4f1d1b72011-07-07 12:29:15 +080023
243. Program RCW
25 => tftp 1000000 rcw.bin
26 => protect off all
27 => erase e8000000 e801ffff
28 => cp.b 1000000 e8000000 50
29
304. Program FMAN Firmware ucode
31 => tftp 1000000 ucode.bin
32 => protect off all
Prabhakar Kushwahae222b1f2014-01-14 11:34:26 +053033 => erase eff00000 eff3ffff
34 => cp.b 1000000 eff00000 2000
Mingkai Hu4f1d1b72011-07-07 12:29:15 +080035
365. Change DIP-switch
37 SW1[1-5] = 10110
38 Note: 1 stands for 'on', 0 stands for 'off'
39
40Boot from SDCard
41===================
421. Build image
43 make P2041RDB_SDCARD_config
44 make all
45
462. Generate PBL imge
47 Use PE tool to produce a image used to be programed to
48 SDCard which contains RCW and U-Boot image.
49
503. Program the PBL image to SDCard
51 => tftp 1000000 pbl_sd.bin
52 => mmcinfo
Prabhakar Kushwahae222b1f2014-01-14 11:34:26 +053053 => mmc write 1000000 8 672
Mingkai Hu4f1d1b72011-07-07 12:29:15 +080054
554. Program FMAN Firmware ucode
56 => tftp 1000000 ucode.bin
Prabhakar Kushwahae222b1f2014-01-14 11:34:26 +053057 => mmc write 1000000 690 10
Mingkai Hu4f1d1b72011-07-07 12:29:15 +080058
595. Change DIP-switch
60 SW1[1-5] = 01100
61 Note: 1 stands for 'on', 0 stands for 'off'
62
63Boot from SPI flash
64===================
651. Build image
66 make P2041RDB_SPIFLASH_config
67 make all
68
692. Generate PBL imge
70 Use PE tool to produce a image used to be programed to
71 SPI flash which contains RCW and U-Boot image.
72
733. Program the PBL image to SPI flash
74 => tftp 1000000 pbl_spi.bin
75 => spi probe 0
76 => sf erase 0 100000
77 => sf write 1000000 0 $filesize
78
794. Program FMAN Firmware ucode
80 => tftp 1000000 ucode.bin
81 => sf erase 110000 10000
82 => sf write 1000000 110000 $filesize
83
845. Change DIP-switch
85 SW1[1-5] = 10100
86 Note: 1 stands for 'on', 0 stands for 'off'
87
88CPLD command
89============
90The CPLD is used to control the power sequence and some serdes lane
91mux function.
92
93cpld reset - hard reset to default bank
94cpld reset altbank - reset to alternate bank
95cpld lane_mux <lane> <mux_value> - set multiplexed lane pin
96 lane 6: 0 -> slot1 (Default)
97 1 -> SGMII
98 lane a: 0 -> slot2 (Default)
99 1 -> AURORA
100 lane c: 0 -> slot2 (Default)
101 1 -> SATA0
102 lane d: 0 -> slot2 (Default)
103 1 -> SATA1
104
105Using the Device Tree Source File
106=================================
107To create the DTB (Device Tree Binary) image file, use a command
108similar to this:
109 dtc -O dtb -b 0 -p 1024 p2041rdb.dts > p2041rdb.dtb
110
111Or use the following command:
112 {linux-2.6}/make p2041rdb.dtb ARCH=powerpc
113
114then the dtb file will be generated under the following directory:
115 {linux-2.6}/arch/powerpc/boot/p2041rdb.dtb
116
117Booting Linux
118=============
119Place a linux uImage in the TFTP disk area.
120 tftp 1000000 uImage
121 tftp 2000000 rootfs.ext2.gz.uboot
122 tftp 3000000 p2041rdb.dtb
123 bootm 1000000 2000000 3000000