blob: a4249c47c6251017f72eb73fec1acfaa384cc92c [file] [log] [blame]
wdenk281e00a2004-08-01 22:48:16 +00001/*
2 * Copyright (C) 2003 ETC s.r.o.
3 *
4 * This program is free software; you can redistribute it and/or
5 * modify it under the terms of the GNU General Public License as
6 * published by the Free Software Foundation; either version 2 of
7 * the License, or (at your option) any later version.
8 *
9 * This program is distributed in the hope that it will be useful,
10 * but WITHOUT ANY WARRANTY; without even the implied warranty of
11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
12 * GNU General Public License for more details.
13 *
14 * You should have received a copy of the GNU General Public License
15 * along with this program; if not, write to the Free Software
16 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
17 * MA 02111-1307 USA
18 *
19 * Written by Peter Figuli <peposh@etc.sk>, 2003.
20 *
21 * 2003/13/06 Initial MP10 Support copied from wepep250
22 */
23
24#ifndef __CONFIG_H
25#define __CONFIG_H
26
27#define CONFIG_ARM920T 1 /* this is an ARM920T CPU */
28#define CONFIG_IMX 1 /* in a Motorola MC9328MXL Chip */
29#define CONFIG_SCB9328 1 /* on a scb9328tronix board */
30#undef CONFIG_USE_IRQ /* don't need use IRQ/FIQ */
31
32#define CONFIG_IMX_SERIAL1
33/*
34 * Select serial console configuration
35 */
36
37
38/*
39 * Definition of u-boot build in commands. Check out CONFIG_CMD_DFL if
40 * neccessary in include/cmd_confdefs.h file. (Un)comment for getting
41 * functionality or size of u-boot code.
42 */
43#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
44 & ~CFG_CMD_LOADS \
45 & ~CFG_CMD_CONSOLE \
46 & ~CFG_CMD_AUTOSCRIPT \
47 | CFG_CMD_NET \
48 | CFG_CMD_PING \
49 | CFG_CMD_DHCP \
50 )
51
52#include <cmd_confdefs.h>
53
54/*
55 * Boot options. Setting delay to -1 stops autostart count down.
56 * NOTE: Sending parameters to kernel depends on kernel version and
57 * 2.4.19-rmk6-pxa1 patch used while my u-boot coding didn't accept
58 * parameters at all! Do not get confused by them so.
59 */
60#define CONFIG_BOOTDELAY -1
61#define CONFIG_BOOTARGS "console=ttySMX0,115200n8 root=/dev/mtdblock3 rootfstype=jffs2 mtdparts=scb9328_flash:128k(U-boot)ro,128k(U-boot_env),1m(kernel),4m(root),4m(fs) eval_board=evk9328"
62#define CONFIG_BOOTCOMMAND "bootm 10040000"
63#define CONFIG_SHOW_BOOT_PROGRESS
64#define CONFIG_ETHADDR 80:81:82:83:84:85
65#define CONFIG_NETMASK 255.255.255.0
66#define CONFIG_IPADDR 10.10.10.9
67#define CONFIG_SERVERIP 10.10.10.10
68
69/*
70 * General options for u-boot. Modify to save memory foot print
71 */
72#define CFG_LONGHELP /* undef saves memory */
73#define CFG_PROMPT "scb9328> " /* prompt string */
74#define CFG_CBSIZE 256 /* console I/O buffer */
75#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer size */
76#define CFG_MAXARGS 16 /* max command args */
77#define CFG_BARGSIZE CFG_CBSIZE /* boot args buf size */
78
79#define CFG_MEMTEST_START 0x08100000 /* memtest test area */
80#define CFG_MEMTEST_END 0x08F00000
81
82#undef CFG_CLKS_IN_HZ /* use HZ for freq. display */
83
84#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
85#define CFG_CPUSPEED 0x141 /* core clock - register value */
86
87#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
88#define CONFIG_BAUDRATE 115200
89/*
90 * Definitions related to passing arguments to kernel.
91 */
92#define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */
93#define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */
94#define CONFIG_INITRD_TAG 1 /* send initrd params */
95#undef CONFIG_VFD /* do not send framebuffer setup */
96
97
98/*
99 * Malloc pool need to host env + 128 Kb reserve for other allocations.
100 */
101#define CFG_MALLOC_LEN (CFG_ENV_SIZE + (128<<10) )
102
103
104#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
105
106#define CONFIG_STACKSIZE (120<<10) /* stack size */
107
108#ifdef CONFIG_USE_IRQ
109#define CONFIG_STACKSIZE_IRQ (4<<10) /* IRQ stack */
110#define CONFIG_STACKSIZE_FIQ (4<<10) /* FIQ stack */
111#endif
112
113/* SDRAM Setup Values
1140x910a8300 Precharge Command CAS 3
1150x910a8200 Precharge Command CAS 2
116
1170xa10a8300 AutoRefresh Command CAS 3
1180xa10a8200 Set AutoRefresh Command CAS 2 */
119
120#define PRECHARGE_CMD 0x910a8200
121#define AUTOREFRESH_CMD 0xa10a8200
wdenk281e00a2004-08-01 22:48:16 +0000122
123/*
124 * SDRAM Memory Map
125 */
126/* SH FIXME */
127#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SDRAM */
128#define SCB9328_SDRAM_1 0x08000000 /* SDRAM bank #1 */
129#define SCB9328_SDRAM_1_SIZE 0x01000000 /* 16 MB */
130
131/*
132 * Flash Controller settings
133 */
134
135/*
136 * Hardware drivers
137 */
138
139
140/*
141 * Configuration for FLASH memory for the Synertronixx board
142 */
143
144/* #define SCB9328_FLASH_32M */
145
146/* 32MB */
147#ifdef SCB9328_FLASH_32M
148#define CFG_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
149#define CFG_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */
150#define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */
151#define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */
152#define SCB9328_FLASH_BANK_SIZE 0x02000000 /* size of one flash bank */
153#define SCB9328_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */
154#define SCB9328_FLASH_BASE 0x10000000 /* location of flash memory */
155#define SCB9328_FLASH_UNLOCK 1 /* perform hw unlock first */
156#else
157
158/* 16MB */
159#define CFG_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
160#define CFG_MAX_FLASH_SECT 128 /* number of sector in FLASH bank */
161#define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */
162#define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */
163#define SCB9328_FLASH_BANK_SIZE 0x01000000 /* size of one flash bank */
164#define SCB9328_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */
165#define SCB9328_FLASH_BASE 0x10000000 /* location of flash memory */
166#define SCB9328_FLASH_UNLOCK 1 /* perform hw unlock first */
167#endif /* SCB9328_FLASH_32M */
168
169/* This should be defined if CFI FLASH device is present. Actually benefit
170 is not so clear to me. In other words we can provide more informations
171 to user, but this expects more complex flash handling we do not provide
172 now.*/
173#undef CFG_FLASH_CFI
174
175#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* timeout for Erase operation */
176#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* timeout for Write operation */
177
178#define CFG_FLASH_BASE SCB9328_FLASH_BASE
179
180/*
181 * This is setting for JFFS2 support in u-boot.
182 * Right now there is no gain for user, but later on booting kernel might be
183 * possible. Consider using XIP kernel running from flash to save RAM
184 * footprint.
185 * NOTE: Enable CFG_CMD_JFFS2 for JFFS2 support.
186 */
187#define CFG_JFFS2_FIRST_BANK 0
188#define CFG_JFFS2_FIRST_SECTOR 5
189#define CFG_JFFS2_NUM_BANKS 1
190
191/*
192 * Environment setup. Definitions of monitor location and size with
193 * definition of environment setup ends up in 2 possibilities.
194 * 1. Embeded environment - in u-boot code is space for environment
195 * 2. Environment is read from predefined sector of flash
196 * Right now we support 2. possiblity, but expecting no env placed
197 * on mentioned address right now. This also needs to provide whole
198 * sector for it - for us 256Kb is really waste of memory. U-boot uses
199 * default env. and until kernel parameters could be sent to kernel
200 * env. has no sense to us.
201 */
202
203/* Setup for PA23 which is Reset Default PA23 but has to become
204 CS5 */
205
206#define CFG_GPR_A_VAL 0x00800000
207#define CFG_GIUS_A_VAL 0x0043fffe
208
209#define CFG_MONITOR_BASE 0x10000000
210#define CFG_MONITOR_LEN 0x20000 /* 128b ( 1 flash sector ) */
211#define CFG_ENV_IS_IN_FLASH 1
212#define CFG_ENV_ADDR 0x10020000 /* absolute address for now */
213#define CFG_ENV_SIZE 0x20000
214
215#define CONFIG_ENV_OVERWRITE 1 /* env is not writable now */
216
217/*
218 * CSxU_VAL:
219 * 63| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x|32
220 * |DTACK_SEL|0|BCD | BCS | PSZ|PME|SYNC| DOL | CNC| WSC | 0| WWS | EDC |
221 *
222 * CSxL_VAL:
223 * 31| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x| 0
224 * | OEA | OEN | WEA | WEN | CSA |EBC| DSZ | 0|SP|0|WP| 0 0|PA|CSEN|
225 */
226
227#define CFG_CS0U_VAL 0x000F2000
228#define CFG_CS0L_VAL 0x11110d01
229#define CFG_CS1U_VAL 0x000F0a00
230#define CFG_CS1L_VAL 0x11110601
231#define CFG_CS2U_VAL 0x0
232#define CFG_CS2L_VAL 0x0
233
234#define CFG_CS3U_VAL 0x000FFFFF
235#define CFG_CS3L_VAL 0x00000303
236
237#define CFG_CS4U_VAL 0x000F0a00
238#define CFG_CS4L_VAL 0x11110301
239
240/* CNC == 3 too long
241 #define CFG_CS5U_VAL 0x0000C210 */
242
243/* #define CFG_CS5U_VAL 0x00008400
244 mal laenger mahcen, ob der bei 150MHz laenger haelt dann und
245 kaum langsamer ist */
246/* #define CFG_CS5U_VAL 0x00009400
247 #define CFG_CS5L_VAL 0x11010D03 */
248
249#define CFG_CS5U_VAL 0x00008400
250#define CFG_CS5L_VAL 0x00000D03
251
252#define CONFIG_DRIVER_DM9000 1
253#define CONFIG_DRIVER_DM9000 1
254#define CONFIG_DM9000_BASE 0x16000000
255#define DM9000_IO CONFIG_DM9000_BASE
256#define DM9000_DATA (CONFIG_DM9000_BASE+4)
257/* #define CONFIG_DM9000_USE_8BIT */
258#define CONFIG_DM9000_USE_16BIT
259/* #define CONFIG_DM9000_USE_32BIT */
260
261/* f_{dpll}=2*f{ref}*(MFI+MFN/(MFD+1))/(PD+1)
262 f_ref=16,777MHz
263
264 0x002a141f: 191,9944MHz
265 0x040b2007: 144MHz
266 0x042a141f: 96MHz
267 0x0811140d: 64MHz
268 0x040e200e: 150MHz
269 0x00321431: 200MHz
270
271 0x08001800: 64MHz mit 16er Quarz
272 0x04001800: 96MHz mit 16er Quarz
273 0x04002400: 144MHz mit 16er Quarz
274
275 31 |x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x| 0
276 |XXX|--PD---|-------MFD---------|XXX|--MFI--|-----MFN-----------| */
277
278#define CPU200
279
280#ifdef CPU200
281#define CFG_MPCTL0_VAL 0x00321431
282#else
283#define CFG_MPCTL0_VAL 0x040e200e
284#endif
285
286/* #define BUS64 */
287#define BUS72
288
289#ifdef BUS72
290#define CFG_SPCTL0_VAL 0x04002400
291#endif
292
293#ifdef BUS96
294#define CFG_SPCTL0_VAL 0x04001800
295#endif
296
297#ifdef BUS64
298#define CFG_SPCTL0_VAL 0x08001800
299#endif
300
301/* Das ist der BCLK Divider, der aus der System PLL
302 BCLK und HCLK erzeugt:
303 31 | xxxx xxxx xxxx xxxx xx10 11xx xxxx xxxx | 0
304 0x2f008403 : 192MHz/2=96MHz, 144MHz/2=72MHz PRESC=1->BCLKDIV=2
305 0x2f008803 : 192MHz/3=64MHz, 240MHz/3=80MHz PRESC=1->BCLKDIV=2
306 0x2f001003 : 192MHz/5=38,4MHz
307 0x2f000003 : 64MHz/1
308 Bit 22: SPLL Restart
309 Bit 21: MPLL Restart */
310
311#ifdef BUS64
312#define CFG_CSCR_VAL 0x2f030003
313#endif
314
315#ifdef BUS72
316#define CFG_CSCR_VAL 0x2f030403
317#endif
318
319/*
320 * Well this has to be defined, but on the other hand it is used differently
321 * one may expect. For instance loadb command do not cares :-)
322 * So advice is - do not relay on this...
323 */
324#define CFG_LOAD_ADDR 0x08400000
325
326#define MHZ16QUARZINUSE
327
328#ifdef MHZ16QUARZINUSE
329#define CONFIG_SYSPLL_CLK_FREQ 16000000
330#else
331#define CONFIG_SYSPLL_CLK_FREQ 16780000
332#endif
333
334#define CONFIG_SYS_CLK_FREQ 16780000
335
336/* FMCR Bit 0 becomes 0 to make CS3 CS3 :P */
337#define CFG_FMCR_VAL 0x00000001
338
339/* Bit[0:3] contain PERCLK1DIV for UART 1
340 0x000b00b ->b<- -> 192MHz/12=16MHz
341 0x000b00b ->8<- -> 144MHz/09=16MHz
342 0x000b00b ->3<- -> 64MHz/4=16MHz */
343
344#ifdef BUS96
345#define CFG_PCDR_VAL 0x000b00b5
346#endif
347
348#ifdef BUS64
349#define CFG_PCDR_VAL 0x000b00b3
350#endif
351
352#ifdef BUS72
353#define CFG_PCDR_VAL 0x000b00b8
354#endif
355
356#endif /* __CONFIG_H */