masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 1 | /* |
| 2 | * board/renesas/blanche/blanche.c |
| 3 | * This file is blanche board support. |
| 4 | * |
| 5 | * Copyright (C) 2016 Renesas Electronics Corporation |
| 6 | * |
| 7 | * SPDX-License-Identifier: GPL-2.0 |
| 8 | */ |
| 9 | |
| 10 | #include <common.h> |
| 11 | #include <malloc.h> |
| 12 | #include <netdev.h> |
| 13 | #include <dm.h> |
| 14 | #include <dm/platform_data/serial_sh.h> |
| 15 | #include <asm/processor.h> |
| 16 | #include <asm/mach-types.h> |
| 17 | #include <asm/io.h> |
Masahiro Yamada | 1221ce4 | 2016-09-21 11:28:55 +0900 | [diff] [blame] | 18 | #include <linux/errno.h> |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 19 | #include <asm/arch/sys_proto.h> |
| 20 | #include <asm/gpio.h> |
| 21 | #include <asm/arch/rmobile.h> |
| 22 | #include <asm/arch/rcar-mstp.h> |
| 23 | #include <asm/arch/mmc.h> |
| 24 | #include <asm/arch/sh_sdhi.h> |
| 25 | #include <miiphy.h> |
| 26 | #include <i2c.h> |
| 27 | #include <mmc.h> |
| 28 | #include "qos.h" |
| 29 | |
| 30 | DECLARE_GLOBAL_DATA_PTR; |
| 31 | |
| 32 | struct pin_db { |
| 33 | u32 addr; /* register address */ |
| 34 | u32 mask; /* mask value */ |
| 35 | u32 val; /* setting value */ |
| 36 | }; |
| 37 | |
| 38 | #define PMMR 0xE6060000 |
masakazu.mochizuki.wd@hitachi.com | d8fc402 | 2016-05-17 13:53:03 +0900 | [diff] [blame] | 39 | #define GPSR0 0xE6060004 |
| 40 | #define GPSR1 0xE6060008 |
| 41 | #define GPSR4 0xE6060014 |
| 42 | #define GPSR5 0xE6060018 |
| 43 | #define GPSR6 0xE606001C |
| 44 | #define GPSR7 0xE6060020 |
| 45 | #define GPSR8 0xE6060024 |
| 46 | #define GPSR9 0xE6060028 |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 47 | #define GPSR10 0xE606002C |
masakazu.mochizuki.wd@hitachi.com | d8fc402 | 2016-05-17 13:53:03 +0900 | [diff] [blame] | 48 | #define GPSR11 0xE6060030 |
| 49 | #define IPSR6 0xE6060058 |
| 50 | #define PUPR2 0xE6060108 |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 51 | #define PUPR3 0xE606010C |
masakazu.mochizuki.wd@hitachi.com | d8fc402 | 2016-05-17 13:53:03 +0900 | [diff] [blame] | 52 | #define PUPR4 0xE6060110 |
| 53 | #define PUPR5 0xE6060114 |
| 54 | #define PUPR7 0xE606011C |
| 55 | #define PUPR9 0xE6060124 |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 56 | #define PUPR10 0xE6060128 |
| 57 | #define PUPR11 0xE606012C |
| 58 | |
| 59 | #define CPG_PLL1CR 0xE6150028 |
| 60 | #define CPG_PLL3CR 0xE61500DC |
| 61 | |
| 62 | #define SetREG(x) \ |
| 63 | writel((readl((x)->addr) & ~((x)->mask)) | ((x)->val), (x)->addr) |
| 64 | |
| 65 | #define SetGuardREG(x) \ |
| 66 | { \ |
| 67 | u32 val; \ |
| 68 | val = (readl((x)->addr) & ~((x)->mask)) | ((x)->val); \ |
| 69 | writel(~val, PMMR); \ |
| 70 | writel(val, (x)->addr); \ |
| 71 | } |
| 72 | |
| 73 | struct pin_db pin_guard[] = { |
masakazu.mochizuki.wd@hitachi.com | d8fc402 | 2016-05-17 13:53:03 +0900 | [diff] [blame] | 74 | { GPSR0, 0xFFFFFFFF, 0x0BFFFFFF }, |
| 75 | { GPSR1, 0xFFFFFFFF, 0x002FFFFF }, |
| 76 | { GPSR4, 0xFFFFFFFF, 0x00000FFF }, |
| 77 | { GPSR5, 0xFFFFFFFF, 0x00010FFF }, |
| 78 | { GPSR6, 0xFFFFFFFF, 0x00010FFF }, |
| 79 | { GPSR7, 0xFFFFFFFF, 0x00010FFF }, |
| 80 | { GPSR8, 0xFFFFFFFF, 0x00010FFF }, |
| 81 | { GPSR9, 0xFFFFFFFF, 0x00010FFF }, |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 82 | { GPSR10, 0xFFFFFFFF, 0x04006000 }, |
masakazu.mochizuki.wd@hitachi.com | d8fc402 | 2016-05-17 13:53:03 +0900 | [diff] [blame] | 83 | { GPSR11, 0xFFFFFFFF, 0x303FEFE0 }, |
| 84 | { IPSR6, 0xFFFFFFFF, 0x0002000E }, |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 85 | }; |
| 86 | |
| 87 | struct pin_db pin_tbl[] = { |
masakazu.mochizuki.wd@hitachi.com | d8fc402 | 2016-05-17 13:53:03 +0900 | [diff] [blame] | 88 | { PUPR2, 0xFFFFFFFF, 0x00000000 }, |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 89 | { PUPR3, 0xFFFFFFFF, 0x0803FF40 }, |
masakazu.mochizuki.wd@hitachi.com | d8fc402 | 2016-05-17 13:53:03 +0900 | [diff] [blame] | 90 | { PUPR4, 0xFFFFFFFF, 0x0000FFFF }, |
| 91 | { PUPR5, 0xFFFFFFFF, 0x00010FFF }, |
| 92 | { PUPR7, 0xFFFFFFFF, 0x0001AFFF }, |
| 93 | { PUPR9, 0xFFFFFFFF, 0x0001CFFF }, |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 94 | { PUPR10, 0xFFFFFFFF, 0xC0438001 }, |
| 95 | { PUPR11, 0xFFFFFFFF, 0x0FC00007 }, |
| 96 | }; |
| 97 | |
| 98 | void pin_init(void) |
| 99 | { |
| 100 | struct pin_db *db; |
| 101 | |
| 102 | for (db = pin_guard; db < &pin_guard[sizeof(pin_guard)/sizeof(struct pin_db)]; db++) { |
| 103 | SetGuardREG(db); |
| 104 | } |
| 105 | for (db = pin_tbl; db < &pin_tbl[sizeof(pin_tbl) /sizeof(struct pin_db)]; db++) { |
| 106 | SetREG(db); |
| 107 | } |
| 108 | } |
| 109 | |
| 110 | #define s_init_wait(cnt) \ |
| 111 | ({ \ |
| 112 | volatile u32 i = 0x10000 * cnt; \ |
| 113 | while (i > 0) \ |
| 114 | i--; \ |
| 115 | }) |
| 116 | |
| 117 | void s_init(void) |
| 118 | { |
| 119 | struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE; |
| 120 | struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE; |
| 121 | u32 cpu_type; |
| 122 | |
| 123 | cpu_type = rmobile_get_cpu_type(); |
| 124 | if (cpu_type == 0x4A) { |
| 125 | writel(0x4D000000, CPG_PLL1CR); |
| 126 | writel(0x4F000000, CPG_PLL3CR); |
| 127 | } |
| 128 | |
| 129 | /* Watchdog init */ |
| 130 | writel(0xA5A5A500, &rwdt->rwtcsra); |
| 131 | writel(0xA5A5A500, &swdt->swtcsra); |
| 132 | |
| 133 | /* QoS(Quality-of-Service) Init */ |
| 134 | qos_init(); |
| 135 | |
| 136 | /* SCIF Init */ |
| 137 | pin_init(); |
| 138 | |
Masahiro Yamada | e856bdc | 2017-02-11 22:43:54 +0900 | [diff] [blame] | 139 | #if defined(CONFIG_MTD_NOR_FLASH) |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 140 | struct rcar_lbsc *lbsc = (struct rcar_lbsc *)LBSC_BASE; |
| 141 | struct rcar_dbsc3 *dbsc3_0 = (struct rcar_dbsc3 *)DBSC3_0_BASE; |
| 142 | |
| 143 | /* LBSC */ |
| 144 | writel(0x00000020, &lbsc->cs0ctrl); |
| 145 | writel(0x00000020, &lbsc->cs1ctrl); |
| 146 | writel(0x00002020, &lbsc->ecs0ctrl); |
| 147 | writel(0x00002020, &lbsc->ecs1ctrl); |
| 148 | |
| 149 | writel(0x2A103320, &lbsc->cswcr0); |
| 150 | writel(0x2A103320, &lbsc->cswcr1); |
| 151 | writel(0x19102110, &lbsc->ecswcr0); |
| 152 | writel(0x19102110, &lbsc->ecswcr1); |
| 153 | |
| 154 | /* DBSC3 */ |
| 155 | s_init_wait(10); |
| 156 | |
| 157 | writel(0x0000A55A, &dbsc3_0->dbpdlck); |
| 158 | |
| 159 | writel(0x21000000, &dbsc3_0->dbcmd); /* opc=RstH (RESET => H) */ |
| 160 | writel(0x11000000, &dbsc3_0->dbcmd); /* opc=PDXt(CKE=H) */ |
| 161 | writel(0x10000000, &dbsc3_0->dbcmd); /* opc=PDEn(CKE=L) */ |
| 162 | |
| 163 | /* Stop Auto-Calibration */ |
| 164 | writel(0x00000001, &dbsc3_0->dbpdrga); |
| 165 | writel(0x80000000, &dbsc3_0->dbpdrgd); |
| 166 | |
| 167 | writel(0x00000004, &dbsc3_0->dbpdrga); |
| 168 | while ((readl(&dbsc3_0->dbpdrgd) & 0x00000001) != 0x00000001); |
| 169 | |
| 170 | /* PLLCR: PLL Control Register */ |
| 171 | writel(0x00000006, &dbsc3_0->dbpdrga); |
| 172 | writel(0x0001C000, &dbsc3_0->dbpdrgd); // > DDR1440 |
| 173 | |
| 174 | /* DXCCR: DATX8 Common Configuration Register */ |
| 175 | writel(0x0000000F, &dbsc3_0->dbpdrga); |
| 176 | writel(0x00181EE4, &dbsc3_0->dbpdrgd); |
| 177 | |
| 178 | /* DSGCR :DDR System General Configuration Register */ |
| 179 | writel(0x00000010, &dbsc3_0->dbpdrga); |
| 180 | writel(0xF00464DB, &dbsc3_0->dbpdrgd); |
| 181 | |
| 182 | writel(0x00000061, &dbsc3_0->dbpdrga); |
| 183 | writel(0x0000008D, &dbsc3_0->dbpdrgd); |
| 184 | |
| 185 | /* Re-Execute ZQ calibration */ |
| 186 | writel(0x00000001, &dbsc3_0->dbpdrga); |
| 187 | writel(0x00000073, &dbsc3_0->dbpdrgd); |
| 188 | |
| 189 | writel(0x00000007, &dbsc3_0->dbkind); |
| 190 | writel(0x0F030A02, &dbsc3_0->dbconf0); |
| 191 | writel(0x00000001, &dbsc3_0->dbphytype); |
| 192 | writel(0x00000000, &dbsc3_0->dbbl); |
| 193 | |
| 194 | writel(0x0000000B, &dbsc3_0->dbtr0); // tCL=11 |
| 195 | writel(0x00000008, &dbsc3_0->dbtr1); // tCWL=8 |
| 196 | writel(0x00000000, &dbsc3_0->dbtr2); // tAL=0 |
| 197 | writel(0x0000000B, &dbsc3_0->dbtr3); // tRCD=11 |
| 198 | writel(0x000C000B, &dbsc3_0->dbtr4); // tRPA=12,tRP=11 |
| 199 | writel(0x00000027, &dbsc3_0->dbtr5); // tRC = 39 |
| 200 | writel(0x0000001C, &dbsc3_0->dbtr6); // tRAS = 28 |
| 201 | writel(0x00000006, &dbsc3_0->dbtr7); // tRRD = 6 |
| 202 | writel(0x00000020, &dbsc3_0->dbtr8); // tRFAW = 32 |
| 203 | writel(0x00000008, &dbsc3_0->dbtr9); // tRDPR = 8 |
| 204 | writel(0x0000000C, &dbsc3_0->dbtr10); // tWR = 12 |
| 205 | writel(0x00000009, &dbsc3_0->dbtr11); // tRDWR = 9 |
| 206 | writel(0x00000012, &dbsc3_0->dbtr12); // tWRRD = 18 |
| 207 | writel(0x000000D0, &dbsc3_0->dbtr13); // tRFC = 208 |
| 208 | writel(0x00140005, &dbsc3_0->dbtr14); |
| 209 | writel(0x00050004, &dbsc3_0->dbtr15); |
| 210 | writel(0x70233005, &dbsc3_0->dbtr16); /* DQL = 35, WDQL = 5 */ |
| 211 | writel(0x000C0000, &dbsc3_0->dbtr17); |
| 212 | writel(0x00000300, &dbsc3_0->dbtr18); |
| 213 | writel(0x00000040, &dbsc3_0->dbtr19); |
| 214 | writel(0x00000001, &dbsc3_0->dbrnk0); |
| 215 | writel(0x00020001, &dbsc3_0->dbadj0); |
| 216 | writel(0x20082004, &dbsc3_0->dbadj2); /* blanche QoS rev0.1 */ |
| 217 | writel(0x00020002, &dbsc3_0->dbwt0cnf0); /* 1600 */ |
| 218 | writel(0x0000001F, &dbsc3_0->dbwt0cnf4); |
| 219 | |
| 220 | while ((readl(&dbsc3_0->dbdfistat) & 0x00000001) != 0x00000001); |
| 221 | writel(0x00000011, &dbsc3_0->dbdficnt); |
| 222 | |
| 223 | /* PGCR1 :PHY General Configuration Register 1 */ |
| 224 | writel(0x00000003, &dbsc3_0->dbpdrga); |
| 225 | writel(0x0300C4E1, &dbsc3_0->dbpdrgd); /* DDR3 */ |
| 226 | |
| 227 | /* PGCR2: PHY General Configuration Registers 2 */ |
| 228 | writel(0x00000023, &dbsc3_0->dbpdrga); |
| 229 | writel(0x00FCDB60, &dbsc3_0->dbpdrgd); |
| 230 | |
| 231 | writel(0x00000011, &dbsc3_0->dbpdrga); |
| 232 | writel(0x1000040B, &dbsc3_0->dbpdrgd); |
| 233 | |
| 234 | /* DTPR0 :DRAM Timing Parameters Register 0 */ |
| 235 | writel(0x00000012, &dbsc3_0->dbpdrga); |
| 236 | writel(0x9D9CBB66, &dbsc3_0->dbpdrgd); |
| 237 | |
| 238 | /* DTPR1 :DRAM Timing Parameters Register 1 */ |
| 239 | writel(0x00000013, &dbsc3_0->dbpdrga); |
| 240 | writel(0x1A868400, &dbsc3_0->dbpdrgd); |
| 241 | |
| 242 | /* DTPR2 ::DRAM Timing Parameters Register 2 */ |
| 243 | writel(0x00000014, &dbsc3_0->dbpdrga); |
| 244 | writel(0x300214D8, &dbsc3_0->dbpdrgd); |
| 245 | |
| 246 | /* MR0 :Mode Register 0 */ |
| 247 | writel(0x00000015, &dbsc3_0->dbpdrga); |
| 248 | writel(0x00000D70, &dbsc3_0->dbpdrgd); |
| 249 | |
| 250 | /* MR1 :Mode Register 1 */ |
| 251 | writel(0x00000016, &dbsc3_0->dbpdrga); |
| 252 | writel(0x00000004, &dbsc3_0->dbpdrgd); /* DRAM Drv 40ohm */ |
| 253 | |
| 254 | /* MR2 :Mode Register 2 */ |
| 255 | writel(0x00000017, &dbsc3_0->dbpdrga); |
| 256 | writel(0x00000018, &dbsc3_0->dbpdrgd); /* CWL=8 */ |
| 257 | |
| 258 | /* VREF(ZQCAL) */ |
| 259 | writel(0x0000001A, &dbsc3_0->dbpdrga); |
| 260 | writel(0x910035C7, &dbsc3_0->dbpdrgd); |
| 261 | |
| 262 | /* PGSR0 :PHY General Status Registers 0 */ |
| 263 | writel(0x00000004, &dbsc3_0->dbpdrga); |
| 264 | while ((readl(&dbsc3_0->dbpdrgd) & 0x00000001) != 0x00000001); |
| 265 | |
| 266 | /* DRAM Init (set MRx etc) */ |
| 267 | writel(0x00000001, &dbsc3_0->dbpdrga); |
| 268 | writel(0x00000181, &dbsc3_0->dbpdrgd); |
| 269 | |
| 270 | /* CKE = H */ |
| 271 | writel(0x11000000, &dbsc3_0->dbcmd); /* opc=PDXt(CKE=H) */ |
| 272 | |
| 273 | /* PGSR0 :PHY General Status Registers 0 */ |
| 274 | writel(0x00000004, &dbsc3_0->dbpdrga); |
| 275 | while ((readl(&dbsc3_0->dbpdrgd) & 0x00000001) != 0x00000001); |
| 276 | |
| 277 | /* RAM ACC Training */ |
| 278 | writel(0x00000001, &dbsc3_0->dbpdrga); |
| 279 | writel(0x0000FE01, &dbsc3_0->dbpdrgd); |
| 280 | |
| 281 | /* Bus control 0 */ |
| 282 | writel(0x00000000, &dbsc3_0->dbbs0cnt1); |
| 283 | /* DDR3 Calibration set */ |
| 284 | writel(0x01004C20, &dbsc3_0->dbcalcnf); |
| 285 | /* DDR3 Calibration timing */ |
| 286 | writel(0x014000AA, &dbsc3_0->dbcaltr); |
| 287 | /* Refresh */ |
| 288 | writel(0x00000140, &dbsc3_0->dbrfcnf0); |
| 289 | writel(0x00081860, &dbsc3_0->dbrfcnf1); |
| 290 | writel(0x00010000, &dbsc3_0->dbrfcnf2); |
| 291 | |
| 292 | /* PGSR0 :PHY General Status Registers 0 */ |
| 293 | writel(0x00000004, &dbsc3_0->dbpdrga); |
| 294 | while ((readl(&dbsc3_0->dbpdrgd) & 0x00000001) != 0x00000001); |
| 295 | |
| 296 | /* Enable Auto-Refresh */ |
| 297 | writel(0x00000001, &dbsc3_0->dbrfen); |
| 298 | /* Permit DDR-Access */ |
| 299 | writel(0x00000001, &dbsc3_0->dbacen); |
| 300 | |
| 301 | /* This locks the access to the PHY unit registers */ |
| 302 | writel(0x00000000, &dbsc3_0->dbpdlck); |
Masahiro Yamada | e856bdc | 2017-02-11 22:43:54 +0900 | [diff] [blame] | 303 | #endif /* CONFIG_MTD_NOR_FLASH */ |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 304 | |
| 305 | } |
| 306 | |
| 307 | #define TMU0_MSTP125 (1 << 25) |
| 308 | #define SCIF0_MSTP721 (1 << 21) |
| 309 | #define SDHI0_MSTP314 (1 << 14) |
| 310 | #define QSPI_MSTP917 (1 << 17) |
| 311 | |
| 312 | int board_early_init_f(void) |
| 313 | { |
| 314 | /* TMU0 */ |
| 315 | mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125); |
| 316 | /* SCIF0 */ |
| 317 | mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721); |
| 318 | /* SDHI0 */ |
| 319 | mstp_clrbits_le32(MSTPSR3, SMSTPCR3, SDHI0_MSTP314); |
| 320 | /* QSPI */ |
| 321 | mstp_clrbits_le32(MSTPSR9, SMSTPCR9, QSPI_MSTP917); |
| 322 | |
| 323 | return 0; |
| 324 | } |
| 325 | |
| 326 | DECLARE_GLOBAL_DATA_PTR; |
| 327 | int board_init(void) |
| 328 | { |
| 329 | /* adress of boot parameters */ |
| 330 | gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; |
| 331 | |
| 332 | /* Init PFC controller */ |
| 333 | r8a7792_pinmux_init(); |
| 334 | |
| 335 | gpio_request(GPIO_FN_D0, NULL); |
| 336 | gpio_request(GPIO_FN_D1, NULL); |
| 337 | gpio_request(GPIO_FN_D2, NULL); |
| 338 | gpio_request(GPIO_FN_D3, NULL); |
| 339 | gpio_request(GPIO_FN_D4, NULL); |
| 340 | gpio_request(GPIO_FN_D5, NULL); |
| 341 | gpio_request(GPIO_FN_D6, NULL); |
| 342 | gpio_request(GPIO_FN_D7, NULL); |
| 343 | gpio_request(GPIO_FN_D8, NULL); |
| 344 | gpio_request(GPIO_FN_D9, NULL); |
| 345 | gpio_request(GPIO_FN_D10, NULL); |
| 346 | gpio_request(GPIO_FN_D11, NULL); |
| 347 | gpio_request(GPIO_FN_D12, NULL); |
| 348 | gpio_request(GPIO_FN_D13, NULL); |
| 349 | gpio_request(GPIO_FN_D14, NULL); |
| 350 | gpio_request(GPIO_FN_D15, NULL); |
| 351 | gpio_request(GPIO_FN_A0, NULL); |
| 352 | gpio_request(GPIO_FN_A1, NULL); |
| 353 | gpio_request(GPIO_FN_A2, NULL); |
| 354 | gpio_request(GPIO_FN_A3, NULL); |
| 355 | gpio_request(GPIO_FN_A4, NULL); |
| 356 | gpio_request(GPIO_FN_A5, NULL); |
| 357 | gpio_request(GPIO_FN_A6, NULL); |
| 358 | gpio_request(GPIO_FN_A7, NULL); |
| 359 | gpio_request(GPIO_FN_A8, NULL); |
| 360 | gpio_request(GPIO_FN_A9, NULL); |
| 361 | gpio_request(GPIO_FN_A10, NULL); |
| 362 | gpio_request(GPIO_FN_A11, NULL); |
| 363 | gpio_request(GPIO_FN_A12, NULL); |
| 364 | gpio_request(GPIO_FN_A13, NULL); |
| 365 | gpio_request(GPIO_FN_A14, NULL); |
| 366 | gpio_request(GPIO_FN_A15, NULL); |
| 367 | gpio_request(GPIO_FN_A16, NULL); |
| 368 | gpio_request(GPIO_FN_A17, NULL); |
| 369 | gpio_request(GPIO_FN_A18, NULL); |
| 370 | gpio_request(GPIO_FN_A19, NULL); |
Masahiro Yamada | e856bdc | 2017-02-11 22:43:54 +0900 | [diff] [blame] | 371 | #if !defined(CONFIG_MTD_NOR_FLASH) |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 372 | gpio_request(GPIO_FN_MOSI_IO0, NULL); |
| 373 | gpio_request(GPIO_FN_MISO_IO1, NULL); |
| 374 | gpio_request(GPIO_FN_IO2, NULL); |
| 375 | gpio_request(GPIO_FN_IO3, NULL); |
| 376 | gpio_request(GPIO_FN_SPCLK, NULL); |
| 377 | gpio_request(GPIO_FN_SSL, NULL); |
Masahiro Yamada | e856bdc | 2017-02-11 22:43:54 +0900 | [diff] [blame] | 378 | #else /* CONFIG_MTD_NOR_FLASH */ |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 379 | gpio_request(GPIO_FN_A20, NULL); |
| 380 | gpio_request(GPIO_FN_A21, NULL); |
| 381 | gpio_request(GPIO_FN_A22, NULL); |
| 382 | gpio_request(GPIO_FN_A23, NULL); |
| 383 | gpio_request(GPIO_FN_A24, NULL); |
| 384 | gpio_request(GPIO_FN_A25, NULL); |
Masahiro Yamada | e856bdc | 2017-02-11 22:43:54 +0900 | [diff] [blame] | 385 | #endif /* CONFIG_MTD_NOR_FLASH */ |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 386 | |
| 387 | gpio_request(GPIO_FN_CS1_A26, NULL); |
| 388 | gpio_request(GPIO_FN_EX_CS0, NULL); |
| 389 | gpio_request(GPIO_FN_EX_CS1, NULL); |
| 390 | gpio_request(GPIO_FN_BS, NULL); |
| 391 | gpio_request(GPIO_FN_RD, NULL); |
| 392 | gpio_request(GPIO_FN_WE0, NULL); |
| 393 | gpio_request(GPIO_FN_WE1, NULL); |
| 394 | gpio_request(GPIO_FN_EX_WAIT0, NULL); |
| 395 | gpio_request(GPIO_FN_IRQ0, NULL); |
| 396 | gpio_request(GPIO_FN_IRQ2, NULL); |
| 397 | gpio_request(GPIO_FN_IRQ3, NULL); |
| 398 | gpio_request(GPIO_FN_CS0, NULL); |
| 399 | |
| 400 | /* Init timer */ |
| 401 | timer_init(); |
| 402 | |
| 403 | return 0; |
| 404 | } |
| 405 | |
| 406 | /* |
| 407 | Added for BLANCHE(R-CarV2H board) |
| 408 | */ |
| 409 | int board_eth_init(bd_t *bis) |
| 410 | { |
| 411 | int rc = 0; |
| 412 | |
| 413 | #ifdef CONFIG_SMC911X |
| 414 | #define STR_ENV_ETHADDR "ethaddr" |
| 415 | |
| 416 | struct eth_device *dev; |
| 417 | uchar eth_addr[6]; |
| 418 | |
| 419 | rc = smc911x_initialize(0, CONFIG_SMC911X_BASE); |
| 420 | |
Simon Glass | 35affd7 | 2017-08-03 12:22:14 -0600 | [diff] [blame] | 421 | if (!eth_env_get_enetaddr(STR_ENV_ETHADDR, eth_addr)) { |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 422 | dev = eth_get_dev_by_index(0); |
| 423 | if (dev) { |
Simon Glass | fd1e959 | 2017-08-03 12:22:11 -0600 | [diff] [blame] | 424 | eth_env_set_enetaddr(STR_ENV_ETHADDR, dev->enetaddr); |
masakazu.mochizuki.wd@hitachi.com | 6f107e4 | 2016-04-12 17:11:41 +0900 | [diff] [blame] | 425 | } else { |
| 426 | printf("blanche: Couldn't get eth device\n"); |
| 427 | rc = -1; |
| 428 | } |
| 429 | } |
| 430 | |
| 431 | #endif |
| 432 | |
| 433 | return rc; |
| 434 | } |
| 435 | |
| 436 | int board_mmc_init(bd_t *bis) |
| 437 | { |
| 438 | int ret = -ENODEV; |
| 439 | |
| 440 | #ifdef CONFIG_SH_SDHI |
| 441 | gpio_request(GPIO_FN_SD0_DAT0, NULL); |
| 442 | gpio_request(GPIO_FN_SD0_DAT1, NULL); |
| 443 | gpio_request(GPIO_FN_SD0_DAT2, NULL); |
| 444 | gpio_request(GPIO_FN_SD0_DAT3, NULL); |
| 445 | gpio_request(GPIO_FN_SD0_CLK, NULL); |
| 446 | gpio_request(GPIO_FN_SD0_CMD, NULL); |
| 447 | gpio_request(GPIO_FN_SD0_CD, NULL); |
| 448 | |
| 449 | gpio_request(GPIO_GP_11_12, NULL); |
| 450 | gpio_direction_output(GPIO_GP_11_12, 1); /* power on */ |
| 451 | |
| 452 | |
| 453 | ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI0_BASE, 0, |
| 454 | SH_SDHI_QUIRK_16BIT_BUF); |
| 455 | |
| 456 | if (ret) |
| 457 | return ret; |
| 458 | #endif |
| 459 | return ret; |
| 460 | } |
| 461 | |
| 462 | int dram_init(void) |
| 463 | { |
| 464 | gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; |
| 465 | gd->ram_size = CONFIG_SYS_SDRAM_SIZE; |
| 466 | |
| 467 | return 0; |
| 468 | } |
| 469 | |
| 470 | const struct rmobile_sysinfo sysinfo = { |
| 471 | CONFIG_RMOBILE_BOARD_STRING |
| 472 | }; |
| 473 | |
| 474 | void reset_cpu(ulong addr) |
| 475 | { |
| 476 | } |
| 477 | |
| 478 | static const struct sh_serial_platdata serial_platdata = { |
| 479 | .base = SCIF0_BASE, |
| 480 | .type = PORT_SCIF, |
| 481 | .clk = 14745600, |
| 482 | .clk_mode = EXT_CLK, |
| 483 | }; |
| 484 | |
| 485 | U_BOOT_DEVICE(blanche_serials) = { |
| 486 | .name = "serial_sh", |
| 487 | .platdata = &serial_platdata, |
| 488 | }; |