blob: b45213c245a32a2071cdb93fa7a1f2543fa10d12 [file] [log] [blame]
Tim Schendekehl14c32612011-11-01 23:55:01 +00001/*
2 * (C) Copyright 2011
3 * egnite GmbH <info@egnite.de>
4 *
5 * (C) Copyright 2010
6 * Ole Reinhardt <ole.reinhardt@thermotemp.de>
7 *
Wolfgang Denk1a459662013-07-08 09:37:19 +02008 * SPDX-License-Identifier: GPL-2.0+
Tim Schendekehl14c32612011-11-01 23:55:01 +00009 */
10
11/*
12 * Ethernut 5 general board support
13 *
14 * Ethernut is an open source hardware and software project for
15 * embedded Ethernet devices. Hardware layouts and CAD files are
16 * freely available under BSD-like license.
17 *
18 * Ethernut 5 is the first member of the Ethernut board family
19 * with U-Boot and Linux support. This implementation is based
20 * on the original work done by Ole Reinhardt, but heavily modified
21 * to support additional features and the latest board revision 5.0F.
22 *
23 * Main board components are by default:
24 *
25 * Atmel AT91SAM9XE512 CPU with 512 kBytes NOR Flash
26 * 2 x 64 MBytes Micron MT48LC32M16A2P SDRAM
27 * 512 MBytes Micron MT29F4G08ABADA NAND Flash
28 * 4 MBytes Atmel AT45DB321D DataFlash
29 * SMSC LAN8710 Ethernet PHY
30 * Atmel ATmega168 MCU used for power management
31 * Linear Technology LTC4411 PoE controller
32 *
33 * U-Boot relevant board interfaces are:
34 *
35 * 100 Mbit Ethernet with IEEE 802.3af PoE
36 * RS-232 serial port
37 * USB host and device
38 * MMC/SD-Card slot
39 * Expansion port with I2C, SPI and more...
40 *
41 * Typically the U-Boot image is loaded from serial DataFlash into
42 * SDRAM by the samboot boot loader, which is located in internal
43 * NOR Flash and provides all essential initializations like CPU
44 * and peripheral clocks and, of course, the SDRAM configuration.
45 *
46 * For testing purposes it is also possibly to directly transfer
47 * the image into SDRAM via JTAG. A tested configuration exists
48 * for the Turtelizer 2 hardware dongle and the OpenOCD software.
49 * In this case the latter will do the basic hardware configuration
50 * via its reset-init script.
51 *
52 * For additional information visit the project home page at
53 * http://www.ethernut.de/
54 */
55
56#include <common.h>
57#include <net.h>
58#include <netdev.h>
59#include <miiphy.h>
60#include <i2c.h>
61#include <spi.h>
62#include <dataflash.h>
63#include <mmc.h>
Andreas Bießmann77c3d842012-03-13 05:01:51 +000064#include <atmel_mci.h>
Tim Schendekehl14c32612011-11-01 23:55:01 +000065
66#include <asm/arch/at91sam9260.h>
67#include <asm/arch/at91sam9260_matrix.h>
68#include <asm/arch/at91sam9_smc.h>
69#include <asm/arch/at91_common.h>
70#include <asm/arch/at91_pmc.h>
71#include <asm/arch/at91_spi.h>
72#include <asm/arch/gpio.h>
73#include <asm/io.h>
Andreas Bießmannac45bb12013-11-29 12:13:45 +010074#include <asm/gpio.h>
Tim Schendekehl14c32612011-11-01 23:55:01 +000075
76#include "ethernut5_pwrman.h"
77
78DECLARE_GLOBAL_DATA_PTR;
79
80AT91S_DATAFLASH_INFO dataflash_info[CONFIG_SYS_MAX_DATAFLASH_BANKS];
81
82struct dataflash_addr cs[CONFIG_SYS_MAX_DATAFLASH_BANKS] = {
83 {CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0, 0}
84};
85
86/*
87 * In fact we have 7 partitions, but u-boot supports 5 only. This is
88 * no big deal, because the first partition is reserved for applications
89 * and the last one is used by Nut/OS. Both need not to be visible here.
90 */
91dataflash_protect_t area_list[NB_DATAFLASH_AREA] = {
92 { 0x00021000, 0x00041FFF, FLAG_PROTECT_SET, 0, "setup" },
93 { 0x00042000, 0x000C5FFF, FLAG_PROTECT_SET, 0, "uboot" },
94 { 0x000C6000, 0x00359FFF, FLAG_PROTECT_SET, 0, "kernel" },
95 { 0x0035A000, 0x003DDFFF, FLAG_PROTECT_SET, 0, "nutos" },
96 { 0x003DE000, 0x003FEFFF, FLAG_PROTECT_CLEAR, 0, "env" }
97};
98
99/*
100 * This is called last during early initialization. Most of the basic
101 * hardware interfaces are up and running.
102 *
103 * The SDRAM hardware has been configured by the first stage boot loader.
104 * We only need to announce its size, using u-boot's memory check.
105 */
106int dram_init(void)
107{
108 gd->ram_size = get_ram_size(
109 (void *)CONFIG_SYS_SDRAM_BASE,
110 CONFIG_SYS_SDRAM_SIZE);
111 return 0;
112}
113
114#ifdef CONFIG_CMD_NAND
115static void ethernut5_nand_hw_init(void)
116{
117 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
118 struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
119 unsigned long csa;
120
121 /* Assign CS3 to NAND/SmartMedia Interface */
122 csa = readl(&matrix->ebicsa);
123 csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
124 writel(csa, &matrix->ebicsa);
125
126 /* Configure SMC CS3 for NAND/SmartMedia */
127 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
128 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
129 &smc->cs[3].setup);
130 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
131 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
132 &smc->cs[3].pulse);
133 writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
134 &smc->cs[3].cycle);
135 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
136 AT91_SMC_MODE_EXNW_DISABLE |
137 AT91_SMC_MODE_DBW_8 |
138 AT91_SMC_MODE_TDF_CYCLE(2),
139 &smc->cs[3].mode);
140
141#ifdef CONFIG_SYS_NAND_READY_PIN
142 /* Ready pin is optional. */
143 at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1);
144#endif
Andreas Bießmannac45bb12013-11-29 12:13:45 +0100145 gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
Tim Schendekehl14c32612011-11-01 23:55:01 +0000146}
147#endif
148
149/*
150 * This is called first during late initialization.
151 */
152int board_init(void)
153{
154 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
155
156 /* Enable clocks for all PIOs */
157 writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
158 (1 << ATMEL_ID_PIOC),
159 &pmc->pcer);
160 /* Set adress of boot parameters. */
161 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
162 /* Initialize UARTs and power management. */
163 at91_seriald_hw_init();
164 ethernut5_power_init();
165#ifdef CONFIG_CMD_NAND
166 ethernut5_nand_hw_init();
167#endif
168#ifdef CONFIG_HAS_DATAFLASH
169 at91_spi0_hw_init(1 << 0);
170#endif
171 return 0;
172}
173
174#ifdef CONFIG_MACB
175/*
176 * This is optionally called last during late initialization.
177 */
178int board_eth_init(bd_t *bis)
179{
180 const char *devname;
181 unsigned short mode;
182 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
183
184 /* Enable on-chip EMAC clock. */
185 writel(1 << ATMEL_ID_EMAC0, &pmc->pcer);
186 /* Need to reset PHY via power management. */
187 ethernut5_phy_reset();
188 /* Set peripheral pins. */
189 at91_macb_hw_init();
190 /* Basic EMAC initialization. */
191 if (macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, CONFIG_PHY_ID))
192 return -1;
193 /*
194 * Early board revisions have a pull-down at the PHY's MODE0
195 * strap pin, which forces the PHY into power down. Here we
196 * switch to all-capable mode.
197 */
198 devname = miiphy_get_current_dev();
199 if (miiphy_read(devname, 0, 18, &mode) == 0) {
200 /* Set mode[2:0] to 0b111. */
201 mode |= 0x00E0;
202 miiphy_write(devname, 0, 18, mode);
203 /* Soft reset overrides strap pins. */
204 miiphy_write(devname, 0, MII_BMCR, BMCR_RESET);
205 }
206 /* Sync environment with network devices, needed for nfsroot. */
207 return eth_init(gd->bd);
208}
209#endif
210
211#ifdef CONFIG_GENERIC_ATMEL_MCI
212int board_mmc_init(bd_t *bd)
213{
214 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
215
216 /* Enable MCI clock. */
217 writel(1 << ATMEL_ID_MCI, &pmc->pcer);
218 /* Initialize MCI hardware. */
219 at91_mci_hw_init();
220 /* Register the device. */
221 return atmel_mci_init((void *)ATMEL_BASE_MCI);
222}
223
prabhakar.csengg@gmail.com2271e7c2012-02-23 01:53:40 +0000224int board_mmc_getcd(struct mmc *mmc)
Tim Schendekehl14c32612011-11-01 23:55:01 +0000225{
prabhakar.csengg@gmail.com2271e7c2012-02-23 01:53:40 +0000226 return !at91_get_pio_value(CONFIG_SYS_MMC_CD_PIN);
Tim Schendekehl14c32612011-11-01 23:55:01 +0000227}
228#endif
229
230#ifdef CONFIG_ATMEL_SPI
231/*
232 * Note, that u-boot uses different code for SPI bus access. While
233 * memory routines use automatic chip select control, the serial
234 * flash support requires 'manual' GPIO control. Thus, we switch
235 * modes.
236 */
237void spi_cs_activate(struct spi_slave *slave)
238{
239 /* Enable NPCS0 in GPIO mode. This disables peripheral control. */
240 at91_set_pio_output(AT91_PIO_PORTA, 3, 0);
241}
242
243void spi_cs_deactivate(struct spi_slave *slave)
244{
245 /* Disable NPCS0 in GPIO mode. */
246 at91_set_pio_output(AT91_PIO_PORTA, 3, 1);
247 /* Switch back to peripheral chip select control. */
248 at91_set_a_periph(AT91_PIO_PORTA, 3, 1);
249}
250
251int spi_cs_is_valid(unsigned int bus, unsigned int cs)
252{
253 return bus == 0 && cs == 0;
254}
255#endif