blob: aec835276bcfbe57d31539ca3a921fb585319abe [file] [log] [blame]
Dirk Behmef904cdb2009-01-27 18:19:12 +01001/*
2 * (C) Copyright 2006-2008
3 * Texas Instruments.
4 * Richard Woodruff <r-woodruff2@ti.com>
5 * Syed Mohammed Khasim <x0khasim@ti.com>
6 *
7 * Configuration settings for the TI OMAP3530 Beagle board.
8 *
Wolfgang Denk3765b3e2013-10-07 13:07:26 +02009 * SPDX-License-Identifier: GPL-2.0+
Dirk Behmef904cdb2009-01-27 18:19:12 +010010 */
11
12#ifndef __CONFIG_H
13#define __CONFIG_H
Dirk Behmef904cdb2009-01-27 18:19:12 +010014
Tom Rinidf4dbb52014-04-03 15:17:15 -040015#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
16
Dirk Behmef904cdb2009-01-27 18:19:12 +010017/*
Tom Rinidf4dbb52014-04-03 15:17:15 -040018 * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
19 * 64 bytes before this address should be set aside for u-boot.img's
20 * header. That is 0x800FFFC0--0x80100000 should not be used for any
21 * other needs. We use this rather than the inherited defines from
22 * ti_armv7_common.h for backwards compatibility.
Dirk Behmef904cdb2009-01-27 18:19:12 +010023 */
Tom Rinidf4dbb52014-04-03 15:17:15 -040024#define CONFIG_SYS_TEXT_BASE 0x80100000
25#define CONFIG_SPL_BSS_START_ADDR 0x80000000
26#define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */
27#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
28#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
Dirk Behmef904cdb2009-01-27 18:19:12 +010029
Tom Rinidf4dbb52014-04-03 15:17:15 -040030#include <configs/ti_omap3_common.h>
Dirk Behmef904cdb2009-01-27 18:19:12 +010031
Sanjeev Premi6a6b62e2009-04-27 21:27:27 +053032/*
33 * Display CPU and Board information
34 */
35#define CONFIG_DISPLAY_CPUINFO 1
36#define CONFIG_DISPLAY_BOARDINFO 1
37
Dirk Behmef904cdb2009-01-27 18:19:12 +010038#define CONFIG_MISC_INIT_R
39
Dirk Behmef904cdb2009-01-27 18:19:12 +010040#define CONFIG_REVISION_TAG 1
Dirk Behmef904cdb2009-01-27 18:19:12 +010041#define CONFIG_ENV_OVERWRITE
Dirk Behmef904cdb2009-01-27 18:19:12 +010042
Jason Kridner70d8c942011-04-18 17:23:35 -040043/* Status LED */
44#define CONFIG_STATUS_LED 1
45#define CONFIG_BOARD_SPECIFIC_LED 1
46#define STATUS_LED_BIT 0x01
47#define STATUS_LED_STATE STATUS_LED_ON
48#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
49#define STATUS_LED_BIT1 0x02
50#define STATUS_LED_STATE1 STATUS_LED_ON
51#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
52#define STATUS_LED_BOOT STATUS_LED_BIT
53#define STATUS_LED_GREEN STATUS_LED_BIT1
54
Jason Kridnerf74fc4a2011-07-22 23:42:44 -050055/* Enable Multi Bus support for I2C */
56#define CONFIG_I2C_MULTI_BUS 1
57
58/* Probe all devices */
Sanjeev Premi8c4e0ca2011-09-05 00:25:53 +000059#define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}}
Jason Kridnerf74fc4a2011-07-22 23:42:44 -050060
Tom Rix25374bf2009-10-31 12:37:43 -050061/* USB */
Ilya Yanokc2af3452012-11-06 13:48:31 +000062#define CONFIG_USB_MUSB_OMAP2PLUS
Paul Kocialkowski95de1e22015-08-04 17:04:06 +020063#define CONFIG_USB_MUSB_PIO_ONLY
Tom Rix25374bf2009-10-31 12:37:43 -050064#define CONFIG_TWL4030_USB 1
Ilya Yanokc642b152012-11-06 13:48:30 +000065#define CONFIG_USB_ETHER
66#define CONFIG_USB_ETHER_RNDIS
Rob Herringdd5b68f2014-05-05 15:08:11 -050067#define CONFIG_G_DNL_VENDOR_NUM 0x0451
68#define CONFIG_G_DNL_PRODUCT_NUM 0xd022
69#define CONFIG_G_DNL_MANUFACTURER "TI"
Paul Kocialkowski17da3c02015-06-12 19:56:59 +020070#define CONFIG_USB_FUNCTION_FASTBOOT
Rob Herringdd5b68f2014-05-05 15:08:11 -050071#define CONFIG_CMD_FASTBOOT
72#define CONFIG_ANDROID_BOOT_IMAGE
Paul Kocialkowskia588d992015-07-20 12:38:22 +020073#define CONFIG_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR
74#define CONFIG_FASTBOOT_BUF_SIZE 0x07000000
Tom Rix25374bf2009-10-31 12:37:43 -050075
Alexander Hollerd90859a2011-04-19 09:30:35 -040076/* USB EHCI */
77#define CONFIG_CMD_USB
78#define CONFIG_USB_EHCI
Govindraj.R928c4bd2012-02-06 03:55:32 +000079
Ilya Yanok29321c02012-02-06 03:55:33 +000080#define CONFIG_USB_EHCI_OMAP
Ilya Yanok29321c02012-02-06 03:55:33 +000081#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
82
Alexander Hollerd90859a2011-04-19 09:30:35 -040083#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
Koen Kooi21624392011-06-17 09:31:09 +020084#define CONFIG_USB_HOST_ETHER
Koen Kooi54b62d52011-06-17 09:47:08 +020085#define CONFIG_USB_ETHER_ASIX
Gerhard Sittiga7434152014-03-08 19:46:16 +010086#define CONFIG_USB_ETHER_MCS7830
Gerhard Sittigeddf6d22014-03-08 19:46:15 +010087#define CONFIG_USB_ETHER_SMSC95XX
Koen Kooi21624392011-06-17 09:31:09 +020088
Stefan Roesece23b182013-12-17 14:14:06 +010089/* GPIO banks */
90#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */
91#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
Alexander Hollerd90859a2011-04-19 09:30:35 -040092
Dirk Behmef904cdb2009-01-27 18:19:12 +010093/* commands to include */
Tom Rini776bebb2012-05-21 11:20:46 +000094#define CONFIG_CMD_ASKENV
95
Heiko Schocher95c6f6d2010-09-17 13:10:31 +020096#define CONFIG_CMD_CACHE
Tom Rinidf4dbb52014-04-03 15:17:15 -040097
Nishanth Menon917cfc72009-03-25 22:13:56 +010098#define MTDIDS_DEFAULT "nand0=nand"
99#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
100 "1920k(u-boot),128k(u-boot-env),"\
101 "4m(kernel),-(fs)"
Dirk Behmef904cdb2009-01-27 18:19:12 +0100102
Alexander Hollerd90859a2011-04-19 09:30:35 -0400103#define CONFIG_USB_STORAGE /* USB storage support */
Dirk Behmef904cdb2009-01-27 18:19:12 +0100104#define CONFIG_CMD_NAND /* NAND support */
Jason Kridner70d8c942011-04-18 17:23:35 -0400105#define CONFIG_CMD_LED /* LED support */
Tyler Bakerfafee9e2014-06-23 11:11:29 -0700106#define CONFIG_CMD_DHCP
Dirk Behmef904cdb2009-01-27 18:19:12 +0100107
Koen Kooi25a4d012011-06-21 22:18:01 +0200108#define CONFIG_VIDEO_OMAP3 /* DSS Support */
Dirk Behmef904cdb2009-01-27 18:19:12 +0100109
110/*
Tom Rix2c155132009-06-28 12:52:30 -0500111 * TWL4030
112 */
Tom Rix2c155132009-06-28 12:52:30 -0500113#define CONFIG_TWL4030_LED 1
114
115/*
Dirk Behmef904cdb2009-01-27 18:19:12 +0100116 * Board NAND Info.
117 */
118#define CONFIG_NAND_OMAP_GPMC
Dirk Behmef904cdb2009-01-27 18:19:12 +0100119#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
120 /* devices */
Dirk Behmef904cdb2009-01-27 18:19:12 +0100121
Dirk Behmef904cdb2009-01-27 18:19:12 +0100122#define CONFIG_EXTRA_ENV_SETTINGS \
Jason Kridnerf4b36ea2011-07-23 00:01:14 -0500123 "loadaddr=0x80200000\0" \
124 "rdaddr=0x81000000\0" \
Nishanth Menon2ade4962013-07-15 07:11:32 -0500125 "fdt_high=0xffffffff\0" \
126 "fdtaddr=0x80f80000\0" \
Tom Rix25374bf2009-10-31 12:37:43 -0500127 "usbtty=cdc_acm\0" \
Nishanth Menona33e3c72013-07-15 07:11:29 -0500128 "bootfile=uImage\0" \
Nishanth Menon102ce9e2013-07-15 07:11:31 -0500129 "ramdisk=ramdisk.gz\0" \
130 "bootdir=/boot\0" \
131 "bootpart=0:2\0" \
Koen Kooi27b8c8f2011-11-27 03:51:06 +0000132 "console=ttyO2,115200n8\0" \
Koen Kooif6e593b2011-04-18 17:28:32 -0400133 "mpurate=auto\0" \
Peter Meerwald847b83d2012-07-02 03:43:31 +0000134 "buddy=none\0" \
Jason Kridnerc522eac2011-09-03 23:37:24 -0400135 "optargs=\0" \
136 "camera=none\0" \
Steve Sakoman13d2cb92009-10-10 14:29:37 -0400137 "vram=12M\0" \
Jason Kridnerf4b36ea2011-07-23 00:01:14 -0500138 "dvimode=640x480MR-16@60\0" \
Steve Sakoman13d2cb92009-10-10 14:29:37 -0400139 "defaultdisplay=dvi\0" \
Steve Sakoman0cd31142010-09-19 21:19:48 -0700140 "mmcdev=0\0" \
Steve Sakoman13d2cb92009-10-10 14:29:37 -0400141 "mmcroot=/dev/mmcblk0p2 rw\0" \
142 "mmcrootfstype=ext3 rootwait\0" \
Steve Sakoman3c6e50d2011-09-30 09:29:11 +0000143 "nandroot=ubi0:rootfs ubi.mtd=4\0" \
144 "nandrootfstype=ubifs\0" \
Jason Kridnerf4b36ea2011-07-23 00:01:14 -0500145 "ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
146 "ramrootfstype=ext2\0" \
Dirk Behmef904cdb2009-01-27 18:19:12 +0100147 "mmcargs=setenv bootargs console=${console} " \
Jason Kridnerc522eac2011-09-03 23:37:24 -0400148 "${optargs} " \
Steve Sakoman5af32462010-02-03 14:39:14 -0800149 "mpurate=${mpurate} " \
Koen Kooib1660312011-08-11 00:39:28 -0500150 "buddy=${buddy} "\
Jason Kridnerc522eac2011-09-03 23:37:24 -0400151 "camera=${camera} "\
Steve Sakoman13d2cb92009-10-10 14:29:37 -0400152 "vram=${vram} " \
153 "omapfb.mode=dvi:${dvimode} " \
Steve Sakoman13d2cb92009-10-10 14:29:37 -0400154 "omapdss.def_disp=${defaultdisplay} " \
155 "root=${mmcroot} " \
156 "rootfstype=${mmcrootfstype}\0" \
Dirk Behmef904cdb2009-01-27 18:19:12 +0100157 "nandargs=setenv bootargs console=${console} " \
Jason Kridnerc522eac2011-09-03 23:37:24 -0400158 "${optargs} " \
Steve Sakoman5af32462010-02-03 14:39:14 -0800159 "mpurate=${mpurate} " \
Koen Kooib1660312011-08-11 00:39:28 -0500160 "buddy=${buddy} "\
Jason Kridnerc522eac2011-09-03 23:37:24 -0400161 "camera=${camera} "\
Steve Sakoman13d2cb92009-10-10 14:29:37 -0400162 "vram=${vram} " \
163 "omapfb.mode=dvi:${dvimode} " \
Steve Sakoman13d2cb92009-10-10 14:29:37 -0400164 "omapdss.def_disp=${defaultdisplay} " \
165 "root=${nandroot} " \
166 "rootfstype=${nandrootfstype}\0" \
Nishanth Menon2ade4962013-07-15 07:11:32 -0500167 "findfdt=" \
168 "if test $beaglerev = AxBx; then " \
169 "setenv fdtfile omap3-beagle.dtb; fi; " \
170 "if test $beaglerev = Cx; then " \
171 "setenv fdtfile omap3-beagle.dtb; fi; " \
Robert Nelson5c9038b2014-01-17 09:51:28 -0600172 "if test $beaglerev = C4; then " \
173 "setenv fdtfile omap3-beagle.dtb; fi; " \
Nishanth Menon2ade4962013-07-15 07:11:32 -0500174 "if test $beaglerev = xMAB; then " \
Robert Nelson3d47ffb2014-05-02 15:14:39 -0500175 "setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \
Nishanth Menon2ade4962013-07-15 07:11:32 -0500176 "if test $beaglerev = xMC; then " \
177 "setenv fdtfile omap3-beagle-xm.dtb; fi; " \
178 "if test $fdtfile = undefined; then " \
179 "echo WARNING: Could not determine device tree to use; fi; \0" \
Robert Nelson4fa24272014-05-02 15:15:03 -0500180 "validatefdt=" \
181 "if test $beaglerev = xMAB; then " \
182 "if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \
183 "setenv fdtfile omap3-beagle-xm.dtb; " \
184 "fi; " \
185 "fi; \0" \
Jason Kridnerf835ea72010-07-21 07:41:25 -0500186 "bootenv=uEnv.txt\0" \
187 "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
Alexander Hollercf073e42011-04-18 17:25:13 -0400188 "importbootenv=echo Importing environment from mmc ...; " \
Alexander Holler44bd26f2014-07-14 17:49:56 +0200189 "env import -t -r $loadaddr $filesize\0" \
Jason Kridnerf4b36ea2011-07-23 00:01:14 -0500190 "ramargs=setenv bootargs console=${console} " \
191 "${optargs} " \
192 "mpurate=${mpurate} " \
193 "buddy=${buddy} "\
194 "vram=${vram} " \
195 "omapfb.mode=dvi:${dvimode} " \
196 "omapdss.def_disp=${defaultdisplay} " \
197 "root=${ramroot} " \
198 "rootfstype=${ramrootfstype}\0" \
Nishanth Menon102ce9e2013-07-15 07:11:31 -0500199 "loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
200 "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
Guillaume GARDET09642262014-08-26 10:48:13 +0200201 "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
202 "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
203 "source ${loadaddr}\0" \
Robert Nelson4fa24272014-05-02 15:15:03 -0500204 "loadfdt=run validatefdt; load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
Dirk Behmef904cdb2009-01-27 18:19:12 +0100205 "mmcboot=echo Booting from mmc ...; " \
206 "run mmcargs; " \
207 "bootm ${loadaddr}\0" \
Nishanth Menonea706902013-07-15 07:11:33 -0500208 "mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
209 "run mmcargs; " \
210 "bootz ${loadaddr} - ${fdtaddr}\0" \
Dirk Behmef904cdb2009-01-27 18:19:12 +0100211 "nandboot=echo Booting from nand ...; " \
212 "run nandargs; " \
213 "nand read ${loadaddr} 280000 400000; " \
214 "bootm ${loadaddr}\0" \
Jason Kridnerf4b36ea2011-07-23 00:01:14 -0500215 "ramboot=echo Booting from ramdisk ...; " \
216 "run ramargs; " \
217 "bootm ${loadaddr}\0" \
Joel Fernandesaae58b92011-09-11 08:37:33 +0000218 "userbutton=if gpio input 173; then run userbutton_xm; " \
219 "else run userbutton_nonxm; fi;\0" \
220 "userbutton_xm=gpio input 4;\0" \
221 "userbutton_nonxm=gpio input 7;\0"
Robert P. J. Dayd7aff442012-11-11 23:20:58 +0000222/* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
Dirk Behmef904cdb2009-01-27 18:19:12 +0100223#define CONFIG_BOOTCOMMAND \
Nishanth Menon2ade4962013-07-15 07:11:32 -0500224 "run findfdt; " \
Andrew Bradford66968112012-10-01 05:06:52 +0000225 "mmc dev ${mmcdev}; if mmc rescan; then " \
Joel Fernandesaae58b92011-09-11 08:37:33 +0000226 "if run userbutton; then " \
227 "setenv bootenv uEnv.txt;" \
228 "else " \
Jason Kridnerf835ea72010-07-21 07:41:25 -0500229 "setenv bootenv user.txt;" \
230 "fi;" \
Alexander Hollercf073e42011-04-18 17:25:13 -0400231 "echo SD/MMC found on device ${mmcdev};" \
232 "if run loadbootenv; then " \
Jason Kridnerf835ea72010-07-21 07:41:25 -0500233 "echo Loaded environment from ${bootenv};" \
Alexander Hollercf073e42011-04-18 17:25:13 -0400234 "run importbootenv;" \
235 "fi;" \
236 "if test -n $uenvcmd; then " \
237 "echo Running uenvcmd ...;" \
238 "run uenvcmd;" \
239 "fi;" \
Guillaume GARDET09642262014-08-26 10:48:13 +0200240 "if run loadbootscript; then " \
241 "run bootscript; " \
242 "else " \
243 "if run loadimage; then " \
244 "run mmcboot;" \
245 "fi;" \
246 "fi; " \
Alexander Hollercf073e42011-04-18 17:25:13 -0400247 "fi;" \
248 "run nandboot;" \
Nishanth Menonea706902013-07-15 07:11:33 -0500249 "setenv bootfile zImage;" \
250 "if run loadimage; then " \
251 "run loadfdt;" \
252 "run mmcbootz; " \
253 "fi; " \
Dirk Behmef904cdb2009-01-27 18:19:12 +0100254
Dirk Behmef904cdb2009-01-27 18:19:12 +0100255/*
Manikandan Pillaid3a513c2009-04-21 17:29:05 +0200256 * OMAP3 has 12 GP timers, they can be driven by the system clock
257 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
258 * This rate is divided by a local divisor.
Dirk Behmef904cdb2009-01-27 18:19:12 +0100259 */
Manikandan Pillaid3a513c2009-04-21 17:29:05 +0200260#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
Dirk Behmef904cdb2009-01-27 18:19:12 +0100261
262/*-----------------------------------------------------------------------
Dirk Behmef904cdb2009-01-27 18:19:12 +0100263 * FLASH and environment organization
264 */
265
266/* **** PISMO SUPPORT *** */
Luca Ceresoli6cbec7b2011-04-20 11:02:05 -0400267#if defined(CONFIG_CMD_NAND)
pekon gupta222a3112014-07-18 17:59:41 +0530268#define CONFIG_SYS_FLASH_BASE NAND_BASE
Luca Ceresoli6cbec7b2011-04-20 11:02:05 -0400269#endif
Dirk Behmef904cdb2009-01-27 18:19:12 +0100270
271/* Monitor at start of flash */
272#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
273#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
274
275#define CONFIG_ENV_IS_IN_NAND 1
Tom Rinidf4dbb52014-04-03 15:17:15 -0400276#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
Dirk Behmef904cdb2009-01-27 18:19:12 +0100277#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
278#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
279
Luca Ceresoli6cbec7b2011-04-20 11:02:05 -0400280#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
281#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
Dirk Behmef904cdb2009-01-27 18:19:12 +0100282#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
283
Dirk Behme53736ba2010-12-11 11:01:00 -0500284#define CONFIG_OMAP3_SPI
285
Aneesh V8e408522011-11-21 23:38:59 +0000286#define CONFIG_SYS_CACHELINE_SIZE 64
287
Tom Rini75c57a32011-11-18 12:48:08 +0000288/* Defines for SPL */
Tom Rini75c57a32011-11-18 12:48:08 +0000289#define CONFIG_SPL_OMAP3_ID_NAND
Tom Rini75c57a32011-11-18 12:48:08 +0000290
291/* NAND boot config */
Stefano Babic55f1b392015-07-26 15:18:15 +0200292#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
Tom Rini75c57a32011-11-18 12:48:08 +0000293#define CONFIG_SYS_NAND_5_ADDR_CYCLE
294#define CONFIG_SYS_NAND_PAGE_COUNT 64
295#define CONFIG_SYS_NAND_PAGE_SIZE 2048
296#define CONFIG_SYS_NAND_OOBSIZE 64
297#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
298#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
299#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
300 10, 11, 12, 13}
301#define CONFIG_SYS_NAND_ECCSIZE 512
302#define CONFIG_SYS_NAND_ECCBYTES 3
pekon gupta3f719062013-11-18 19:03:01 +0530303#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
Tom Rini75c57a32011-11-18 12:48:08 +0000304#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
pekon gupta434f2cf2014-07-18 17:59:42 +0530305/* NAND: SPL falcon mode configs */
306#ifdef CONFIG_SPL_OS_BOOT
307#define CONFIG_CMD_SPL_NAND_OFS 0x240000
308#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
309#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
310#endif
Tom Rini75c57a32011-11-18 12:48:08 +0000311
Dirk Behmef904cdb2009-01-27 18:19:12 +0100312#endif /* __CONFIG_H */