blob: bc264276d4687a01942187efca325ae163c8d577 [file] [log] [blame]
Alison Wang186fc4d2012-10-18 19:25:52 +00001/*
2 * Configuation settings for the Freescale MCF54418 TWR board.
3 *
4 * Copyright 2010-2012 Freescale Semiconductor, Inc.
5 * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
6 *
Wolfgang Denk1a459662013-07-08 09:37:19 +02007 * SPDX-License-Identifier: GPL-2.0+
Alison Wang186fc4d2012-10-18 19:25:52 +00008 */
9
10/*
11 * board/config.h - configuration options, board specific
12 */
13
14#ifndef _M54418TWR_H
15#define _M54418TWR_H
16
17/*
18 * High Level Configuration Options
19 * (easy to change)
20 */
21#define CONFIG_MCF5441x /* define processor family */
22#define CONFIG_M54418 /* define processor type */
23#define CONFIG_M54418TWR /* M54418TWR board */
24
25#define CONFIG_MCFUART
26#define CONFIG_SYS_UART_PORT (0)
27#define CONFIG_BAUDRATE 115200
28#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
29
30#undef CONFIG_WATCHDOG
31
32#define CONFIG_TIMESTAMP /* Print image info with timestamp */
33
34/*
35 * BOOTP options
36 */
37#define CONFIG_BOOTP_BOOTFILESIZE
38#define CONFIG_BOOTP_BOOTPATH
39#define CONFIG_BOOTP_GATEWAY
40#define CONFIG_BOOTP_HOSTNAME
41
42/* Command line configuration */
43#include <config_cmd_default.h>
44
45#define CONFIG_CMD_BOOTD
46#define CONFIG_CMD_CACHE
47#undef CONFIG_CMD_DATE
48#define CONFIG_CMD_DHCP
49#define CONFIG_CMD_ELF
50#undef CONFIG_CMD_FLASH
51#undef CONFIG_CMD_I2C
52#undef CONFIG_CMD_JFFS2
53#undef CONFIG_CMD_UBI
54#define CONFIG_CMD_MEMORY
55#define CONFIG_CMD_MISC
56#define CONFIG_CMD_MII
57#undef CONFIG_CMD_NAND
58#undef CONFIG_CMD_NAND_YAFFS
59#define CONFIG_CMD_NET
60#define CONFIG_CMD_NFS
61#define CONFIG_CMD_PING
62#define CONFIG_CMD_REGINFO
63#define CONFIG_CMD_SPI
64#define CONFIG_CMD_SF
65#undef CONFIG_CMD_IMLS
66
67#undef CONFIG_CMD_LOADB
68#undef CONFIG_CMD_LOADS
69
70/*
71 * NAND FLASH
72 */
73#ifdef CONFIG_CMD_NAND
74#define CONFIG_JFFS2_NAND
75#define CONFIG_NAND_FSL_NFC
76#define CONFIG_SYS_NAND_BASE 0xFC0FC000
77#define CONFIG_SYS_MAX_NAND_DEVICE 1
78#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
79#define CONFIG_SYS_NAND_SELECT_DEVICE
80#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
81#endif
82
83/* Network configuration */
84#define CONFIG_MCFFEC
85#ifdef CONFIG_MCFFEC
86#define CONFIG_NET_MULTI 1
87#define CONFIG_MII 1
88#define CONFIG_MII_INIT 1
89#define CONFIG_SYS_DISCOVER_PHY
90#define CONFIG_SYS_RX_ETH_BUFFER 2
91#define CONFIG_SYS_FAULT_ECCONFIG_SYS_NO_FLASHHO_LINK_DOWN
92#define CONFIG_SYS_TX_ETH_BUFFER 2
93#define CONFIG_HAS_ETH1
94
95#define CONFIG_SYS_FEC0_PINMUX 0
96#define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
97#define CONFIG_SYS_FEC1_PINMUX 0
98#define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_MIIBASE
99#define MCFFEC_TOUT_LOOP 50000
100#define CONFIG_SYS_FEC0_PHYADDR 0
101#define CONFIG_SYS_FEC1_PHYADDR 1
102
103#define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */
104
105#ifdef CONFIG_SYS_NAND_BOOT
106#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rw rootfstype=jffs2 " \
107 "mtdparts=NAND:1M(u-boot)ro,7M(kernel)ro," \
108 "-(jffs2) console=ttyS0,115200"
109#else
110#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=" \
111 __stringify(CONFIG_SERVERIP) ":/tftpboot/" \
112 __stringify(CONFIG_IPADDR) " ip=" \
113 __stringify(CONFIG_IPADDR) ":" \
114 __stringify(CONFIG_SERVERIP)":" \
115 __stringify(CONFIG_GATEWAYIP)": " \
116 __stringify(CONFIG_NETMASK) \
117 "::eth0:off:rw console=ttyS0,115200"
118#endif
119
120#define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
121#define CONFIG_ETH1ADDR 00:e0:0c:bc:e5:61
122#define CONFIG_ETHPRIME "FEC0"
123#define CONFIG_IPADDR 192.168.1.2
124#define CONFIG_NETMASK 255.255.255.0
125#define CONFIG_SERVERIP 192.168.1.1
126#define CONFIG_GATEWAYIP 192.168.1.1
127
128#define CONFIG_OVERWRITE_ETHADDR_ONCE
129#define CONFIG_SYS_FEC_BUF_USE_SRAM
130/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
131#ifndef CONFIG_SYS_DISCOVER_PHY
132#define FECDUPLEX FULL
133#define FECSPEED _100BASET
134#define LINKSTATUS 1
135#else
136#define LINKSTATUS 0
137#ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
138#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
139#endif
140#endif /* CONFIG_SYS_DISCOVER_PHY */
141#endif
142
143#define CONFIG_HOSTNAME M54418TWR
144
145#if defined(CONFIG_CF_SBF)
146/* ST Micro serial flash */
147#define CONFIG_SYS_LOAD_ADDR2 0x40010007
148#define CONFIG_EXTRA_ENV_SETTINGS \
149 "netdev=eth0\0" \
150 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
151 "loadaddr=0x40010000\0" \
152 "sbfhdr=sbfhdr.bin\0" \
153 "uboot=u-boot.bin\0" \
154 "load=tftp ${loadaddr} ${sbfhdr};" \
155 "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \
156 "upd=run load; run prog\0" \
157 "prog=sf probe 0:1 1000000 3;" \
158 "sf erase 0 40000;" \
159 "sf write ${loadaddr} 0 40000;" \
160 "save\0" \
161 ""
162#elif defined(CONFIG_SYS_NAND_BOOT)
163#define CONFIG_EXTRA_ENV_SETTINGS \
164 "netdev=eth0\0" \
165 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
166 "loadaddr=0x40010000\0" \
167 "u-boot=u-boot.bin\0" \
168 "load=tftp ${loadaddr} ${u-boot};\0" \
169 "upd=run load; run prog\0" \
170 "prog=nand device 0;" \
171 "nand erase 0 40000;" \
172 "nb_update ${loadaddr} ${filesize};" \
173 "save\0" \
174 ""
175#else
176#define CONFIG_SYS_UBOOT_END 0x3FFFF
177#define CONFIG_EXTRA_ENV_SETTINGS \
178 "netdev=eth0\0" \
179 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
180 "loadaddr=40010000\0" \
181 "u-boot=u-boot.bin\0" \
182 "load=tftp ${loadaddr) ${u-boot}\0" \
183 "upd=run load; run prog\0" \
184 "prog=prot off mram" " ;" \
185 "cp.b ${loadaddr} 0 ${filesize};" \
186 "save\0" \
187 ""
188#endif
189
190/* Realtime clock */
191#undef CONFIG_MCFRTC
192#define CONFIG_RTC_MCFRRTC
193#define CONFIG_SYS_MCFRRTC_BASE 0xFC0A8000
194
195/* Timer */
196#define CONFIG_MCFTMR
197#undef CONFIG_MCFPIT
198
199/* I2c */
Heiko Schocher00f792e2012-10-24 13:48:22 +0200200#undef CONFIG_SYS_FSL_I2C
Alison Wang186fc4d2012-10-18 19:25:52 +0000201#undef CONFIG_HARD_I2C /* I2C with hardware support */
Heiko Schocherea818db2013-01-29 08:53:15 +0100202#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
Alison Wang186fc4d2012-10-18 19:25:52 +0000203/* I2C speed and slave address */
204#define CONFIG_SYS_I2C_SPEED 80000
205#define CONFIG_SYS_I2C_SLAVE 0x7F
206#define CONFIG_SYS_I2C_OFFSET 0x58000
207#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
208
209/* DSPI and Serial Flash */
210#define CONFIG_CF_SPI
211#define CONFIG_CF_DSPI
212#define CONFIG_SERIAL_FLASH
213#define CONFIG_HARD_SPI
214#define CONFIG_SYS_SBFHDR_SIZE 0x7
215#ifdef CONFIG_CMD_SPI
216# define CONFIG_SPI_FLASH
217# define CONFIG_SPI_FLASH_ATMEL
218
219# define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \
220 DSPI_CTAR_PCSSCK_1CLK | \
221 DSPI_CTAR_PASC(0) | \
222 DSPI_CTAR_PDT(0) | \
223 DSPI_CTAR_CSSCK(0) | \
224 DSPI_CTAR_ASC(0) | \
225 DSPI_CTAR_DT(1))
226# define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0)
227# define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0)
228#endif
229
230/* Input, PCI, Flexbus, and VCO */
231#define CONFIG_EXTRA_CLOCK
232
233#define CONFIG_PRAM 2048 /* 2048 KB */
234
235/* HUSH */
236#define CONFIG_SYS_HUSH_PARSER 1
237#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
238
239#define CONFIG_SYS_PROMPT "-> "
240#define CONFIG_SYS_LONGHELP /* undef to save memory */
241
242#if defined(CONFIG_CMD_KGDB)
243#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
244#else
245#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
246#endif
247/* Print Buffer Size */
248#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
249 sizeof(CONFIG_SYS_PROMPT) + 16)
250#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
251/* Boot Argument Buffer Size */
252#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
253
254#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000)
255
256#define CONFIG_SYS_HZ 1000
257
258#define CONFIG_SYS_MBAR 0xFC000000
259
260/*
261 * Low Level Configuration Settings
262 * (address mappings, register initial values, etc.)
263 * You should know what you are doing if you make changes here.
264 */
265
266/*-----------------------------------------------------------------------
267 * Definitions for initial stack pointer and data area (in DPRAM)
268 */
269#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
270/* End of used area in internal SRAM */
271#define CONFIG_SYS_INIT_RAM_SIZE 0x10000
272#define CONFIG_SYS_INIT_RAM_CTRL 0x221
273/* size in bytes reserved for initial data */
274#define CONFIG_SYS_GBL_DATA_SIZE 256
275#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \
276 CONFIG_SYS_GBL_DATA_SIZE) - 32)
277#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
278#define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32)
279
280/*-----------------------------------------------------------------------
281 * Start addresses for the final memory configuration
282 * (Set up by the startup code)
283 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
284 */
285#define CONFIG_SYS_SDRAM_BASE 0x40000000
286#define CONFIG_SYS_SDRAM_SIZE 128 /* SDRAM size in MB */
287
288#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x400)
289#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
290#define CONFIG_SYS_DRAM_TEST
291
292#if defined(CONFIG_CF_SBF) || defined(CONFIG_SYS_NAND_BOOT)
293#define CONFIG_SERIAL_BOOT
294#endif
295
296#if defined(CONFIG_SERIAL_BOOT)
297#define CONFIG_SYS_MONITOR_BASE (TEXT_BASE + 0x400)
298#else
299#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
300#endif
301
302#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024)
303/* Reserve 256 kB for Monitor */
304#define CONFIG_SYS_MONITOR_LEN (256 << 10)
305/* Reserve 256 kB for malloc() */
306#define CONFIG_SYS_MALLOC_LEN (256 << 10)
307
308/*
309 * For booting Linux, the board info and command line data
310 * have to be in the first 8 MB of memory, since this is
311 * the maximum mapped by the Linux kernel during initialization ??
312 */
313/* Initial Memory map for Linux */
314#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \
315 (CONFIG_SYS_SDRAM_SIZE << 20))
316
317/* Configuration for environment
318 * Environment is embedded in u-boot in the second sector of the flash
319 */
320#if !defined(CONFIG_SERIAL_BOOT) /*MRAM boot*/
321#define CONFIG_SYS_NO_FLASH
322#define CONFIG_ENV_IS_IN_MRAM 1
323#define CONFIG_ENV_ADDR (0x40000 - 0x1000) /*MRAM size 40000*/
324#define CONFIG_ENV_SIZE 0x1000
325#endif
326
327#if defined(CONFIG_CF_SBF)
328#define CONFIG_SYS_NO_FLASH
329#define CONFIG_ENV_IS_IN_SPI_FLASH 1
330#define CONFIG_ENV_SPI_CS 1
331#define CONFIG_ENV_OFFSET 0x40000
332#define CONFIG_ENV_SIZE 0x2000
333#define CONFIG_ENV_SECT_SIZE 0x10000
334#endif
335#if defined(CONFIG_SYS_NAND_BOOT)
336#define CONFIG_SYS_NO_FLASH
Jason Jinb765fce2012-10-25 15:27:37 +0800337#define CONFIG_ENV_IS_NOWHERE
Alison Wang186fc4d2012-10-18 19:25:52 +0000338#define CONFIG_ENV_OFFSET 0x80000
339#define CONFIG_ENV_SIZE 0x20000
340#define CONFIG_ENV_SECT_SIZE 0x20000
341#endif
342#undef CONFIG_ENV_OVERWRITE
343
344/* FLASH organization */
345#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
346
347#undef CONFIG_SYS_FLASH_CFI
348#ifdef CONFIG_SYS_FLASH_CFI
349
350#define CONFIG_FLASH_CFI_DRIVER 1
351/* Max size that the board might have */
352#define CONFIG_SYS_FLASH_SIZE 0x1000000
353#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
354/* max number of memory banks */
355#define CONFIG_SYS_MAX_FLASH_BANKS 1
356/* max number of sectors on one chip */
357#define CONFIG_SYS_MAX_FLASH_SECT 270
358/* "Real" (hardware) sectors protection */
359#define CONFIG_SYS_FLASH_PROTECTION
360#define CONFIG_SYS_FLASH_CHECKSUM
361#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE }
362#else
363/* max number of sectors on one chip */
364#define CONFIG_SYS_MAX_FLASH_SECT 270
365/* max number of sectors on one chip */
366#define CONFIG_SYS_MAX_FLASH_BANKS 0
367#endif
368
369/*
370 * This is setting for JFFS2 support in u-boot.
371 * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
372 */
373#ifdef CONFIG_CMD_JFFS2
374#define CONFIG_JFFS2_DEV "nand0"
375#define CONFIG_JFFS2_PART_OFFSET (0x800000)
376#define CONFIG_CMD_MTDPARTS
377#define CONFIG_MTD_DEVICE
378#define MTDIDS_DEFAULT "nand0=m54418twr.nand"
379
380#define MTDPARTS_DEFAULT "mtdparts=m54418twr.nand:1m(data)," \
381 "7m(kernel)," \
382 "-(rootfs)"
383
384#endif
385
386#ifdef CONFIG_CMD_UBI
387#define CONFIG_CMD_MTDPARTS
388#define CONFIG_MTD_DEVICE /* needed for mtdparts command */
389#define CONFIG_MTD_PARTITIONS /* mtdparts and UBI support */
390#define CONFIG_RBTREE
391#define MTDIDS_DEFAULT "nand0=NAND"
392#define MTDPARTS_DEFAULT "mtdparts=NAND:1m(u-boot)," \
393 "-(ubi)"
394#endif
395/* Cache Configuration */
396#define CONFIG_SYS_CACHELINE_SIZE 16
397#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
398 CONFIG_SYS_INIT_RAM_SIZE - 8)
399#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
400 CONFIG_SYS_INIT_RAM_SIZE - 4)
401#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA)
402#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA)
403#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \
404 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
405 CF_ACR_EN | CF_ACR_SM_ALL)
406#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \
407 CF_CACR_ICINVA | CF_CACR_EUSP)
408#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \
409 CF_CACR_DEC | CF_CACR_DDCM_P | \
410 CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
411
412#define CACR_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
413 CONFIG_SYS_INIT_RAM_SIZE - 12)
414
415/*-----------------------------------------------------------------------
416 * Memory bank definitions
417 */
418/*
419 * CS0 - NOR Flash 16MB
420 * CS1 - Available
421 * CS2 - Available
422 * CS3 - Available
423 * CS4 - Available
424 * CS5 - Available
425 */
426
427 /* Flash */
428#define CONFIG_SYS_CS0_BASE 0x00000000
429#define CONFIG_SYS_CS0_MASK 0x000F0101
430#define CONFIG_SYS_CS0_CTRL 0x00001D60
431
432#endif /* _M54418TWR_H */