board/freescale/ls1088a/ls1088a.c

/*
 * Copyright 2017 NXP
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */
#include <common.h>
#include <i2c.h>
#include <malloc.h>
#include <errno.h>
#include <netdev.h>
#include <fsl_ifc.h>
#include <fsl_ddr.h>
#include <fsl_sec.h>
#include <asm/io.h>
#include <fdt_support.h>
#include <libfdt.h>
#include <fsl-mc/fsl_mc.h>
#include <environment.h>
#include <asm/arch-fsl-layerscape/soc.h>
#include <asm/arch/ppa.h>

#include "../common/qixis.h"
#include "ls1088a_qixis.h"

DECLARE_GLOBAL_DATA_PTR;

unsigned long long get_qixis_addr(void)
{
	unsigned long long addr;

	if (gd->flags & GD_FLG_RELOC)
		addr = QIXIS_BASE_PHYS;
	else
		addr = QIXIS_BASE_PHYS_EARLY;

	/*
	 * IFC address under 256MB is mapped to 0x30000000, any address above
	 * is mapped to 0x5_10000000 up to 4GB.
	 */
	addr = addr  > 0x10000000 ? addr + 0x500000000ULL : addr + 0x30000000;

	return addr;
}

int checkboard(void)
{
	char buf[64];
	u8 sw;
	static const char *const freq[] = {"100", "125", "156.25",
					    "100 separate SSCG"};
	int clock;


	printf("Board: LS1088A-RDB, ");

	sw = QIXIS_READ(arch);
	printf("Board Arch: V%d, ", sw >> 4);

	printf("Board version: %c, boot from ", (sw & 0xf) + 'A');


	memset((u8 *)buf, 0x00, ARRAY_SIZE(buf));

	sw = QIXIS_READ(brdcfg[0]);
	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;

#ifdef CONFIG_SD_BOOT
	puts("SD card\n");
#endif
	switch (sw) {
	case 0:

		puts("QSPI:");
		sw = QIXIS_READ(brdcfg[0]);
		sw = (sw & QIXIS_QMAP_MASK) >> QIXIS_QMAP_SHIFT;
		if (sw == 0 || sw == 4)
			puts("0\n");
		else if (sw == 1)
			puts("1\n");
		else
			puts("EMU\n");
		break;

	default:
		printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
		break;
	}


	printf("CPLD: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata));


	/*
	 * Display the actual SERDES reference clocks as configured by the
	 * dip switches on the board.  Note that the SWx registers could
	 * technically be set to force the reference clocks to match the
	 * values that the SERDES expects (or vice versa).  For now, however,
	 * we just display both values and hope the user notices when they
	 * don't match.
	 */
	puts("SERDES1 Reference : ");
	sw = QIXIS_READ(brdcfg[2]);
	clock = (sw >> 6) & 3;
	printf("Clock1 = %sMHz ", freq[clock]);
	clock = (sw >> 4) & 3;
	printf("Clock2 = %sMHz", freq[clock]);

	puts("\nSERDES2 Reference : ");
	clock = (sw >> 2) & 3;
	printf("Clock1 = %sMHz ", freq[clock]);
	clock = (sw >> 0) & 3;
	printf("Clock2 = %sMHz\n", freq[clock]);

	return 0;
}

bool if_board_diff_clk(void)
{
	u8 diff_conf = QIXIS_READ(dutcfg[11]);
	return diff_conf & 0x80;
}

unsigned long get_board_sys_clk(void)
{
	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);

	switch (sysclk_conf & 0x0f) {
	case QIXIS_SYSCLK_83:
		return 83333333;
	case QIXIS_SYSCLK_100:
		return 100000000;
	case QIXIS_SYSCLK_125:
		return 125000000;
	case QIXIS_SYSCLK_133:
		return 133333333;
	case QIXIS_SYSCLK_150:
		return 150000000;
	case QIXIS_SYSCLK_160:
		return 160000000;
	case QIXIS_SYSCLK_166:
		return 166666666;
	}

	return 66666666;
}

unsigned long get_board_ddr_clk(void)
{
	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);

	if (if_board_diff_clk())
		return get_board_sys_clk();
	switch ((ddrclk_conf & 0x30) >> 4) {
	case QIXIS_DDRCLK_100:
		return 100000000;
	case QIXIS_DDRCLK_125:
		return 125000000;
	case QIXIS_DDRCLK_133:
		return 133333333;
	}

	return 66666666;
}

int select_i2c_ch_pca9547(u8 ch)
{
	int ret;

	ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
	if (ret) {
		puts("PCA: failed to select proper channel\n");
		return ret;
	}

	return 0;
}

void board_retimer_init(void)
{
	u8 reg;

	/* Retimer is connected to I2C1_CH5 */
	select_i2c_ch_pca9547(I2C_MUX_CH5);

	/* Access to Control/Shared register */
	reg = 0x0;
	i2c_write(I2C_RETIMER_ADDR, 0xff, 1, &reg, 1);

	/* Read device revision and ID */
	i2c_read(I2C_RETIMER_ADDR, 1, 1, &reg, 1);
	debug("Retimer version id = 0x%x\n", reg);

	/* Enable Broadcast. All writes target all channel register sets */
	reg = 0x0c;
	i2c_write(I2C_RETIMER_ADDR, 0xff, 1, &reg, 1);

	/* Reset Channel Registers */
	i2c_read(I2C_RETIMER_ADDR, 0, 1, &reg, 1);
	reg |= 0x4;
	i2c_write(I2C_RETIMER_ADDR, 0, 1, &reg, 1);

	/* Set data rate as 10.3125 Gbps */
	reg = 0x90;
	i2c_write(I2C_RETIMER_ADDR, 0x60, 1, &reg, 1);
	reg = 0xb3;
	i2c_write(I2C_RETIMER_ADDR, 0x61, 1, &reg, 1);
	reg = 0x90;
	i2c_write(I2C_RETIMER_ADDR, 0x62, 1, &reg, 1);
	reg = 0xb3;
	i2c_write(I2C_RETIMER_ADDR, 0x63, 1, &reg, 1);
	reg = 0xcd;
	i2c_write(I2C_RETIMER_ADDR, 0x64, 1, &reg, 1);

	/* Select VCO Divider to full rate (000) */
	i2c_read(I2C_RETIMER_ADDR, 0x2F, 1, &reg, 1);
	reg &= 0x0f;
	reg |= 0x70;
	i2c_write(I2C_RETIMER_ADDR, 0x2F, 1, &reg, 1);


	/*return the default channel*/
	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
}

int board_init(void)
{
	init_final_memctl_regs();
#if defined(CONFIG_TARGET_LS1088ARDB) && defined(CONFIG_FSL_MC_ENET)
	u32 __iomem *irq_ccsr = (u32 __iomem *)ISC_BASE;
#endif

	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
	board_retimer_init();

#ifdef CONFIG_ENV_IS_NOWHERE
	gd->env_addr = (ulong)&default_environment[0];
#endif

#if defined(CONFIG_TARGET_LS1088ARDB) && defined(CONFIG_FSL_MC_ENET)
	/* invert AQR105 IRQ pins polarity */
	out_le32(irq_ccsr + IRQCR_OFFSET / 4, AQR105_IRQ_MASK);
#endif

#ifdef CONFIG_FSL_LS_PPA
	ppa_init();
#endif
	return 0;
}

int board_early_init_f(void)
{
	fsl_lsch3_early_init_f();
	return 0;
}

void detail_board_ddr_info(void)
{
	puts("\nDDR    ");
	print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
	print_ddr_info(0);
}

#if defined(CONFIG_ARCH_MISC_INIT)
int arch_misc_init(void)
{
#ifdef CONFIG_FSL_CAAM
	sec_init();
#endif
	return 0;
}
#endif

#ifdef CONFIG_FSL_MC_ENET
void fdt_fixup_board_enet(void *fdt)
{
	int offset;

	offset = fdt_path_offset(fdt, "/fsl-mc");

	if (offset < 0)
		offset = fdt_path_offset(fdt, "/fsl,dprc@0");

	if (offset < 0) {
		printf("%s: ERROR: fsl-mc node not found in device tree (error %d)\n",
		       __func__, offset);
		return;
	}

	if (get_mc_boot_status() == 0)
		fdt_status_okay(fdt, offset);
	else
		fdt_status_fail(fdt, offset);
}
#endif

#ifdef CONFIG_OF_BOARD_SETUP
int ft_board_setup(void *blob, bd_t *bd)
{
	int err, i;
	u64 base[CONFIG_NR_DRAM_BANKS];
	u64 size[CONFIG_NR_DRAM_BANKS];

	ft_cpu_setup(blob, bd);

	/* fixup DT for the two GPP DDR banks */
	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
		base[i] = gd->bd->bi_dram[i].start;
		size[i] = gd->bd->bi_dram[i].size;
	}

#ifdef CONFIG_RESV_RAM
	/* reduce size if reserved memory is within this bank */
	if (gd->arch.resv_ram >= base[0] &&
	    gd->arch.resv_ram < base[0] + size[0])
		size[0] = gd->arch.resv_ram - base[0];
	else if (gd->arch.resv_ram >= base[1] &&
		 gd->arch.resv_ram < base[1] + size[1])
		size[1] = gd->arch.resv_ram - base[1];
#endif

	fdt_fixup_memory_banks(blob, base, size, CONFIG_NR_DRAM_BANKS);

#ifdef CONFIG_FSL_MC_ENET
	fdt_fixup_board_enet(blob);
	err = fsl_mc_ldpaa_exit(bd);
	if (err)
		return err;
#endif

	return 0;
}
#endif