blob: ca6580f2978d50c8b20c1938d71ab662421083c8 [file] [log] [blame]
Tom Rini83d290c2018-05-06 17:58:06 -04001/* SPDX-License-Identifier: GPL-2.0+ */
Heiko Schocherd8ccbe92016-06-07 08:31:25 +02002/*
3 * (C) Copyright 2016
4 * Heiko Schocher, DENX Software Engineering, hs@denx.de.
5 *
6 * Based on:
7 * am335x_evm.h
8 *
9 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
Heiko Schocherd8ccbe92016-06-07 08:31:25 +020010 */
11
12#ifndef __CONFIG_AM335X_SHC_H
13#define __CONFIG_AM335X_SHC_H
14
15#include <configs/ti_am335x_common.h>
16
17/* settings we don;t want on this board */
Heiko Schocherd8ccbe92016-06-07 08:31:25 +020018#undef CONFIG_CMD_SPI
Heiko Schocherd8ccbe92016-06-07 08:31:25 +020019
20#define CONFIG_CMD_CACHE
21
22#ifndef CONFIG_SPL_BUILD
23# define CONFIG_TIMESTAMP
Heiko Schocherd8ccbe92016-06-07 08:31:25 +020024#endif
25
26#define CONFIG_SYS_BOOTM_LEN (16 << 20)
27
Heiko Schocherd8ccbe92016-06-07 08:31:25 +020028/* Clock Defines */
29#define V_OSCK 24000000 /* Clock output from T2 */
30#define V_SCLK (V_OSCK)
31
Heiko Schocherd8ccbe92016-06-07 08:31:25 +020032/*
33 * in case of SD Card or Network boot we want to have a possibility to
34 * debrick the shc, therefore do not read environment from eMMC
35 */
36#if defined(CONFIG_SHC_SDBOOT) || defined(CONFIG_SHC_NETBOOT)
37#define CONFIG_SYS_MMC_ENV_DEV 0
38#else
39#define CONFIG_SYS_MMC_ENV_DEV 1
40#endif
41
42/*
43 * Info when using boot partitions: As environment resides within first
44 * 128 kB, MLO must start at 128 kB == 0x20000
45 * ENV at MMC Boot0 Partition - 0/Undefined=user, 1=boot0, 2=boot1,
46 * 4..7=general0..3
47 */
48#define CONFIG_ENV_SIZE 0x1000 /* 4 KB */
49#define CONFIG_ENV_OFFSET 0x7000 /* 28 kB */
50
51#define CONFIG_HSMMC2_8BIT
52
53#define CONFIG_ENV_OFFSET_REDUND 0x9000 /* 36 kB */
54#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
55
Heiko Schocherd8ccbe92016-06-07 08:31:25 +020056#ifndef CONFIG_SHC_ICT
57/*
58 * In builds other than ICT, reset to retry after timeout
59 * Define a timeout after which a stopped bootloader continues autoboot
60 * (only works with CONFIG_RESET_TO_RETRY)
61 */
62# define CONFIG_BOOT_RETRY_TIME 30
63# define CONFIG_RESET_TO_RETRY
64#endif
65
Heiko Schocherd8ccbe92016-06-07 08:31:25 +020066#ifndef CONFIG_SPL_BUILD
67#define CONFIG_EXTRA_ENV_SETTINGS \
68 "loadaddr=0x80200000\0" \
69 "kloadaddr=0x84000000\0" \
70 "fdtaddr=0x85000000\0" \
71 "fdt_high=0xffffffff\0" \
72 "rdaddr=0x81000000\0" \
73 "bootfile=uImage\0" \
74 "fdtfile=am335x-shc.dtb\0" \
75 "verify=no\0" \
76 "serverip=10.55.152.184\0" \
77 "rootpath=/srv/nfs/shc-rootfs\0" \
78 "console=ttyO0,115200n8\0" \
79 "optargs=quiet\0" \
80 "mmcdev=1\0" \
81 "harakiri=0\0" \
82 "mmcpart=2\0" \
83 "active_root=root1\0" \
84 "inactive_root=root2\0" \
85 "mmcrootfstype=ext4 rootwait\0" \
86 "nfsopts=nolock\0" \
87 "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
88 "::off\0" \
89 "ip_method=none\0" \
90 "bootargs_defaults=setenv bootargs " \
91 "console=${console} " \
92 "${optargs}\0" \
93 "mmcargs=run bootargs_defaults;" \
94 "setenv bootargs ${bootargs} " \
95 "root=${mmcroot} " \
96 "rootfstype=${mmcrootfstype} ip=${ip_method}\0" \
97 "netargs=setenv bootargs console=${console} " \
98 "${optargs} " \
99 "root=/dev/nfs " \
100 "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
101 "ip=dhcp\0" \
102 "bootenv=uEnv.txt\0" \
103 "loadbootenv=if fatload mmc ${mmcdev} ${loadaddr} ${bootenv}; then " \
104 "echo Loaded environment from ${bootenv}; " \
105 "run importbootenv; " \
106 "fi;\0" \
107 "importbootenv=echo Importing environment variables from uEnv.txt ...; " \
108 "env import -t $loadaddr $filesize\0" \
109 "loaduimagefat=fatload mmc ${mmcdev} ${kloadaddr} ${bootfile}\0" \
110 "loaduimage=ext2load mmc ${mmcdev}:${mmcpart} ${kloadaddr} /boot/${bootfile}\0" \
111 "loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdtaddr} /boot/${fdtfile}\0" \
112 "netloaduimage=tftp ${loadaddr} ${bootfile}\0" \
113 "netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
114 "mmcboot=echo Booting Linux from ${mmcdevice} ...; " \
115 "run mmcargs; " \
116 "if run loadfdt; then " \
117 "echo device tree detected; " \
118 "bootm ${kloadaddr} - ${fdtaddr}; " \
119 "else " \
120 "bootm ${kloadaddr}; " \
121 "fi; \0" \
122 "netboot=echo Booting from network ...; " \
123 "setenv autoload no; " \
124 "dhcp; " \
125 "run netloaduimage; " \
126 "run netargs; " \
127 "echo NFS path: ${serverip}:${rootpath};" \
128 "if run netloadfdt; then " \
129 "echo device tree detected; " \
130 "bootm ${loadaddr} - ${fdtaddr}; " \
131 "else " \
132 "bootm ${loadaddr}; " \
133 "fi; \0" \
134 "emmc_erase=if test ${harakiri} = 1 ; then echo erase emmc ...; setenv mmcdev 1; mmc erase 0 200; reset; fi; \0" \
135 "mmcpart_gp=mmcpart gp 1 40; \0" \
136 "mmcpart_enhance=mmcpart enhance 0 64; \0" \
137 "mmcpart_rel_write=mmcpart rel_write 1f; \0" \
138 "mmcpart_commit=mmcpart commit 1; \0" \
139 "mmc_hw_part=run mmcpart_gp; run mmcpart_enhance; run mmcpart_rel_write; run mmcpart_commit; \0" \
140 "led_success=gpio set 22; \0" \
141 "fusecmd=mmc dev 1; if mmcpart iscommitted; then echo HW Partitioning already committed; mmcpart list; else run mmc_hw_part; fi; run led_success; \0" \
142 "uenv_exec=if test -n $uenvcmd; then " \
143 "echo Running uenvcmd ...; " \
144 "run uenvcmd; " \
145 "fi;\0" \
146 "sd_setup=echo SD/MMC-Card detected on device 0; " \
147 "setenv mmcdevice SD; " \
148 "setenv mmcdev 0; " \
149 "setenv mmcpart 2; " \
150 "setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0" \
151 "emmc_setup=echo eMMC detected on device 1; " \
152 "setenv mmcdevice eMMC; " \
153 "setenv mmcdev 1; " \
154 "run emmc_erase; " \
155 "if test ${active_root} = root2; then " \
156 "echo Active root is partition 6 (root2); " \
157 "setenv mmcpart 6; " \
158 "else " \
159 "echo Active root is partition 5 (root1); " \
160 "setenv mmcpart 5; " \
161 "fi; " \
162 "setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0"
163#endif /* #ifndef CONFIG_SPL_BUILD */
164
165#if defined CONFIG_SHC_NETBOOT
166/* Network Boot */
167# define CONFIG_BOOTCOMMAND \
168 "run fusecmd; " \
169 "if run netboot; then " \
170 "echo Booting from network; " \
171 "else " \
172 "echo ERROR: Cannot boot from network!; " \
173 "panic; " \
174 "fi; "
175
176#elif defined CONFIG_SHC_SDBOOT /* !defined CONFIG_SHC_NETBOOT */
177/* SD-Card Boot */
178# define CONFIG_BOOTCOMMAND \
179 "if mmc dev 0; mmc rescan; then " \
180 "run sd_setup; " \
181 "else " \
182 "echo ERROR: SD/MMC-Card not detected!; " \
183 "panic; " \
184 "fi; " \
185 "if run loaduimage; then " \
186 "echo Bootable SD/MMC-Card inserted, booting from it!; " \
187 "run mmcboot; " \
188 "else " \
189 "echo ERROR: Unable to load uImage from SD/MMC-Card!; " \
190 "panic; " \
191 "fi; "
192
193#elif defined CONFIG_SHC_ICT
194/* ICT adapter boots only u-boot and does HW partitioning */
195# define CONFIG_BOOTCOMMAND \
196 "if mmc dev 0; mmc rescan; then " \
197 "run sd_setup; " \
198 "else " \
199 "echo ERROR: SD/MMC-Card not detected!; " \
200 "panic; " \
201 "fi; " \
202 "run fusecmd; "
203
204#else /* !defined CONFIG_SHC_NETBOOT, !defined CONFIG_SHC_SDBOOT */
205/* Regular Boot from internal eMMC */
206# define CONFIG_BOOTCOMMAND \
207 "if mmc dev 1; mmc rescan; then " \
208 "run emmc_setup; " \
209 "else " \
210 "echo ERROR: eMMC device not detected!; " \
211 "panic; " \
212 "fi; " \
213 "if run loaduimage; then " \
214 "run mmcboot; " \
215 "else " \
216 "echo ERROR Unable to load uImage from eMMC!; " \
217 "echo Performing Rollback!; " \
218 "setenv _active_ ${active_root}; " \
219 "setenv _inactive_ ${inactive_root}; " \
220 "setenv active_root ${_inactive_}; " \
221 "setenv inactive_root ${_active_}; " \
222 "saveenv; " \
223 "reset; " \
224 "fi; "
225
226#endif /* Regular Boot */
227
228/* NS16550 Configuration */
229#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
230#define CONFIG_SYS_NS16550_COM2 0x48022000 /* UART1 */
231#define CONFIG_SYS_NS16550_COM3 0x48024000 /* UART2 */
232#define CONFIG_SYS_NS16550_COM4 0x481a6000 /* UART3 */
233#define CONFIG_SYS_NS16550_COM5 0x481a8000 /* UART4 */
234#define CONFIG_SYS_NS16550_COM6 0x481aa000 /* UART5 */
Heiko Schocherd8ccbe92016-06-07 08:31:25 +0200235
236/* PMIC support */
237#define CONFIG_POWER_TPS65217
238
239/* SPL */
Heiko Schocherd8ccbe92016-06-07 08:31:25 +0200240
Heiko Schocherd8ccbe92016-06-07 08:31:25 +0200241/*
242 * Disable MMC DM for SPL build and can be re-enabled after adding
243 * DM support in SPL
244 */
245#ifdef CONFIG_SPL_BUILD
246#undef CONFIG_DM_MMC
247#undef CONFIG_TIMER
248#endif
249
Heiko Schocherd8ccbe92016-06-07 08:31:25 +0200250#define CONFIG_MII
251#define CONFIG_BOOTP_DEFAULT
Heiko Schocherd8ccbe92016-06-07 08:31:25 +0200252#define CONFIG_BOOTP_DNS2
253#define CONFIG_BOOTP_SEND_HOSTNAME
Heiko Schocherd8ccbe92016-06-07 08:31:25 +0200254#define CONFIG_NET_RETRY_COUNT 10
Heiko Schocherd8ccbe92016-06-07 08:31:25 +0200255#define CONFIG_PHY_SMSC
256
257/* I2C configuration */
258#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */
259#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
260#define CONFIG_SYS_I2C_SPEED 400000
261#define CONFIG_SYS_I2C_SLAVE 1
262
263#define CONFIG_SHOW_BOOT_PROGRESS
Heiko Schocherd8ccbe92016-06-07 08:31:25 +0200264#endif /* ! __CONFIG_AM335X_SHC_H */