| /** @file | |
| I2C Master Protocol as defined in the PI 1.3 specification. | |
| This protocol manipulates the I2C host controller to perform transactions as a master | |
| on the I2C bus using the current state of any switches or multiplexers in the I2C bus. | |
| Copyright (c) 2013, Intel Corporation. All rights reserved.<BR> | |
| This program and the accompanying materials | |
| are licensed and made available under the terms and conditions of the BSD License | |
| which accompanies this distribution. The full text of the license may be found at | |
| http://opensource.org/licenses/bsd-license.php | |
| THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, | |
| WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. | |
| @par Revision Reference: | |
| This protocol is from PI Version 1.3. | |
| **/ | |
| #ifndef __I2C_MASTER_H__ | |
| #define __I2C_MASTER_H__ | |
| #include <Pi/PiI2c.h> | |
| #define EFI_I2C_MASTER_PROTOCOL_GUID { 0xcd72881f, 0x45b5, 0x4feb, { 0x98, 0xc8, 0x31, 0x3d, 0xa8, 0x11, 0x74, 0x62 }} | |
| typedef struct _EFI_I2C_MASTER_PROTOCOL EFI_I2C_MASTER_PROTOCOL; | |
| /** | |
| Set the frequency for the I2C clock line. | |
| This routine must be called at or below TPL_NOTIFY. | |
| The software and controller do a best case effort of using the specified | |
| frequency for the I2C bus. If the frequency does not match exactly then | |
| the I2C master protocol selects the next lower frequency to avoid | |
| exceeding the operating conditions for any of the I2C devices on the bus. | |
| For example if 400 KHz was specified and the controller's divide network | |
| only supports 402 KHz or 398 KHz then the I2C master protocol selects 398 | |
| KHz. If there are not lower frequencies available, then return | |
| EFI_UNSUPPORTED. | |
| @param[in] This Pointer to an EFI_I2C_MASTER_PROTOCOL structure | |
| @param[in] BusClockHertz Pointer to the requested I2C bus clock frequency | |
| in Hertz. Upon return this value contains the | |
| actual frequency in use by the I2C controller. | |
| @retval EFI_SUCCESS The bus frequency was set successfully. | |
| @retval EFI_ALREADY_STARTED The controller is busy with another transaction. | |
| @retval EFI_INVALID_PARAMETER BusClockHertz is NULL | |
| @retval EFI_UNSUPPORTED The controller does not support this frequency. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_I2C_MASTER_PROTOCOL_SET_BUS_FREQUENCY) ( | |
| IN CONST EFI_I2C_MASTER_PROTOCOL *This, | |
| IN OUT UINTN *BusClockHertz | |
| ); | |
| /** | |
| Reset the I2C controller and configure it for use | |
| This routine must be called at or below TPL_NOTIFY. | |
| The I2C controller is reset. The caller must call SetBusFrequench() after | |
| calling Reset(). | |
| @param[in] This Pointer to an EFI_I2C_MASTER_PROTOCOL structure. | |
| @retval EFI_SUCCESS The reset completed successfully. | |
| @retval EFI_ALREADY_STARTED The controller is busy with another transaction. | |
| @retval EFI_DEVICE_ERROR The reset operation failed. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_I2C_MASTER_PROTOCOL_RESET) ( | |
| IN CONST EFI_I2C_MASTER_PROTOCOL *This | |
| ); | |
| /** | |
| Start an I2C transaction on the host controller. | |
| This routine must be called at or below TPL_NOTIFY. For synchronous | |
| requests this routine must be called at or below TPL_CALLBACK. | |
| This function initiates an I2C transaction on the controller. To | |
| enable proper error handling by the I2C protocol stack, the I2C | |
| master protocol does not support queuing but instead only manages | |
| one I2C transaction at a time. This API requires that the I2C bus | |
| is in the correct configuration for the I2C transaction. | |
| The transaction is performed by sending a start-bit and selecting the | |
| I2C device with the specified I2C slave address and then performing | |
| the specified I2C operations. When multiple operations are requested | |
| they are separated with a repeated start bit and the slave address. | |
| The transaction is terminated with a stop bit. | |
| When Event is NULL, StartRequest operates synchronously and returns | |
| the I2C completion status as its return value. | |
| When Event is not NULL, StartRequest synchronously returns EFI_SUCCESS | |
| indicating that the I2C transaction was started asynchronously. The | |
| transaction status value is returned in the buffer pointed to by | |
| I2cStatus upon the completion of the I2C transaction when I2cStatus | |
| is not NULL. After the transaction status is returned the Event is | |
| signaled. | |
| Note: The typical consumer of this API is the I2C host protocol. | |
| Extreme care must be taken by other consumers of this API to prevent | |
| confusing the third party I2C drivers due to a state change at the | |
| I2C device which the third party I2C drivers did not initiate. I2C | |
| platform specific code may use this API within these guidelines. | |
| @param[in] This Pointer to an EFI_I2C_MASTER_PROTOCOL structure. | |
| @param[in] SlaveAddress Address of the device on the I2C bus. Set the | |
| I2C_ADDRESSING_10_BIT when using 10-bit addresses, | |
| clear this bit for 7-bit addressing. Bits 0-6 | |
| are used for 7-bit I2C slave addresses and bits | |
| 0-9 are used for 10-bit I2C slave addresses. | |
| @param[in] RequestPacket Pointer to an EFI_I2C_REQUEST_PACKET | |
| structure describing the I2C transaction. | |
| @param[in] Event Event to signal for asynchronous transactions, | |
| NULL for asynchronous transactions | |
| @param[out] I2cStatus Optional buffer to receive the I2C transaction | |
| completion status | |
| @retval EFI_SUCCESS The asynchronous transaction was successfully | |
| started when Event is not NULL. | |
| @retval EFI_SUCCESS The transaction completed successfully when | |
| Event is NULL. | |
| @retval EFI_ALREADY_STARTED The controller is busy with another transaction. | |
| @retval EFI_BAD_BUFFER_SIZE The RequestPacket->LengthInBytes value is too | |
| large. | |
| @retval EFI_DEVICE_ERROR There was an I2C error (NACK) during the | |
| transaction. | |
| @retval EFI_INVALID_PARAMETER RequestPacket is NULL | |
| @retval EFI_NOT_FOUND Reserved bit set in the SlaveAddress parameter | |
| @retval EFI_NO_RESPONSE The I2C device is not responding to the slave | |
| address. EFI_DEVICE_ERROR will be returned if | |
| the controller cannot distinguish when the NACK | |
| occurred. | |
| @retval EFI_OUT_OF_RESOURCES Insufficient memory for I2C transaction | |
| @retval EFI_UNSUPPORTED The controller does not support the requested | |
| transaction. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_I2C_MASTER_PROTOCOL_START_REQUEST) ( | |
| IN CONST EFI_I2C_MASTER_PROTOCOL *This, | |
| IN UINTN SlaveAddress, | |
| IN EFI_I2C_REQUEST_PACKET *RequestPacket, | |
| IN EFI_EVENT Event OPTIONAL, | |
| OUT EFI_STATUS *I2cStatus OPTIONAL | |
| ); | |
| /// | |
| /// I2C master mode protocol | |
| /// | |
| /// This protocol manipulates the I2C host controller to perform transactions as a | |
| /// master on the I2C bus using the current state of any switches or multiplexers | |
| /// in the I2C bus. | |
| /// | |
| struct _EFI_I2C_MASTER_PROTOCOL { | |
| /// | |
| /// Set the clock frequency for the I2C bus. | |
| /// | |
| EFI_I2C_MASTER_PROTOCOL_SET_BUS_FREQUENCY SetBusFrequency; | |
| /// | |
| /// Reset the I2C host controller. | |
| /// | |
| EFI_I2C_MASTER_PROTOCOL_RESET Reset; | |
| /// | |
| /// Start an I2C transaction in master mode on the host controller. | |
| /// | |
| EFI_I2C_MASTER_PROTOCOL_START_REQUEST StartRequest; | |
| /// | |
| /// Pointer to an EFI_I2C_CONTROLLER_CAPABILITIES data structure containing | |
| /// the capabilities of the I2C host controller. | |
| /// | |
| CONST EFI_I2C_CONTROLLER_CAPABILITIES *I2cControllerCapabilities; | |
| }; | |
| extern EFI_GUID gEfiI2cMasterProtocolGuid; | |
| #endif // __I2C_MASTER_H__ |