rockchip: Add common default bss and stack addresses
On Rockchip the typical aarch64 boot steps are as follows:
- BROM load TPL to SRAM
- TPL init full DRAM
- use stack in SRAM at TPL_STACK addr
- use malloc heap on stack, size is TPL_SYS_MALLOC_F_LEN
- TPL jump back to BROM
- BROM load SPL to beginning of DRAM
- SPL init storage devices
- use bss in DRAM at SPL_BSS_START_ADDR, size is SPL_BSS_MAX_SIZE
- use stack in DRAM at SPL_STACK addr (or CUSTOM_SYS_INIT_SP_ADDR)
- use malloc heap on stack, size is SPL_SYS_MALLOC_F_LEN
- SPL load FIT images from storage to DRAM
- use stack in DRAM at SPL_STACK_R_ADDR
- use new malloc heap on stack, size is SPL_STACK_R_MALLOC_SIMPLE_LEN
- SPL jump to TF-A at 0x40000
- (optional) TF-A load OPTEE
- TF-A jump to U-Boot proper at TEXT_BASE
- U-Boot proper init pre-reloc devices
- use stack in DRAM at CUSTOM_SYS_INIT_SP_ADDR
- use malloc heap on stack, size is SYS_MALLOC_F_LEN
- U-Boot proper relocate to end of usable DRAM
- U-Boot proper init devices and complete boot
SPL have access to full DRAM, however, current configuration for text
base, stack addr and malloc heap size used at the different boot steps
are at risk of overlapping, e.g. when U-Boot proper + FDT grows close
to 1 MiB on RK3328/RK3399 or when pre-reloc and reloc stack and malloc
heap overlap on ROCK 5A.
Fix this by defining safe defaults for bss, stack and malloc size and
addresses. A range at around [60 MiB, 64 MiB) was chosen to be used for
bss and stack until U-Boot proper have been relocated to end of usable
DRAM. The range was primarily chosen to be able to accommodate SoCs with
a small amount of embedded DRAM, e.g. RK3308G has 64 MiB DRAM.
Overiew of the new common memory layout:
[ 0, 2M) - SPL / TF-A / reserved
[ 2M, +X) - U-Boot proper pre-reloc
[ -X, 64M) - bss, stack and malloc heap
During SPL pre-reloc phase:
[ 0, 256K) - SPL binary is loaded by BROM to beginning of DRAM
[ -X, 63M) - SPL pre-reloc stack
[ -32K, 63M) - SPL pre-reloc malloc heap
[63.5M, +32K) - SPL bss
After SPL reloc phase:
[ 0, 256K) - SPL binary
[ 256K, +X) - TF-A image is loaded by SPL
[ 2M, +X) - U-Boot proper + FDT image is loaded by SPL
[ -X, 62M) - SPL reloc stack
[ 60M, 62M) - SPL reloc malloc heap
[ -32K, 63M) - SPL init malloc heap, memory allocated during SPL
pre-reloc phase is still in use at reloc phase
[63.5M, +32K) - SPL bss
During U-Boot proper pre-reloc phase:
[ 0, 2M) - TF-A / reserved
[ 2M, +X) - U-Boot proper + FDT
[ -X, 63M) - U-Boot proper pre-reloc stack (shared addr with SPL)
[ -64K, 63M) - U-Boot proper pre-reloc malloc heap
After U-Boot proper has relocated to top of memory we should be able to
use 2M+ for loading kernel, initrd, scripts etc.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
1 file changed