omap4: Copy device tree from Linux 5.7.y
Copy all device tree files required for omap4 panda support from
mainline Linux.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
diff --git a/arch/arm/dts/omap4.dtsi b/arch/arm/dts/omap4.dtsi
new file mode 100644
index 0000000..763bdea
--- /dev/null
+++ b/arch/arm/dts/omap4.dtsi
@@ -0,0 +1,657 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#include <dt-bindings/bus/ti-sysc.h>
+#include <dt-bindings/clock/omap4.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/omap.h>
+#include <dt-bindings/clock/omap4.h>
+
+/ {
+ compatible = "ti,omap4430", "ti,omap4";
+ interrupt-parent = <&wakeupgen>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ chosen { };
+
+ aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ next-level-cache = <&L2>;
+ reg = <0x0>;
+
+ clocks = <&dpll_mpu_ck>;
+ clock-names = "cpu";
+
+ clock-latency = <300000>; /* From omap-cpufreq driver */
+ };
+ cpu@1 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ next-level-cache = <&L2>;
+ reg = <0x1>;
+ };
+ };
+
+ /*
+ * Note that 4430 needs cross trigger interface (CTI) supported
+ * before we can configure the interrupts. This means sampling
+ * events are not supported for pmu. Note that 4460 does not use
+ * CTI, see also 4460.dtsi.
+ */
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ ti,hwmods = "debugss";
+ };
+
+ gic: interrupt-controller@48241000 {
+ compatible = "arm,cortex-a9-gic";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x48241000 0x1000>,
+ <0x48240100 0x0100>;
+ interrupt-parent = <&gic>;
+ };
+
+ L2: l2-cache-controller@48242000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x48242000 0x1000>;
+ cache-unified;
+ cache-level = <2>;
+ };
+
+ local-timer@48240600 {
+ compatible = "arm,cortex-a9-twd-timer";
+ clocks = <&mpu_periphclk>;
+ reg = <0x48240600 0x20>;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_EDGE_RISING)>;
+ interrupt-parent = <&gic>;
+ };
+
+ wakeupgen: interrupt-controller@48281000 {
+ compatible = "ti,omap4-wugen-mpu";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x48281000 0x1000>;
+ interrupt-parent = <&gic>;
+ };
+
+ /*
+ * The soc node represents the soc top level view. It is used for IPs
+ * that are not memory mapped in the MPU view or for the MPU itself.
+ */
+ soc {
+ compatible = "ti,omap-infra";
+ mpu {
+ compatible = "ti,omap4-mpu";
+ ti,hwmods = "mpu";
+ sram = <&ocmcram>;
+ };
+
+ dsp {
+ compatible = "ti,omap3-c64";
+ };
+
+ iva {
+ compatible = "ti,ivahd";
+ ti,hwmods = "iva";
+ };
+ };
+
+ /*
+ * XXX: Use a flat representation of the OMAP4 interconnect.
+ * The real OMAP interconnect network is quite complex.
+ * Since it will not bring real advantage to represent that in DT for
+ * the moment, just use a fake OCP bus entry to represent the whole bus
+ * hierarchy.
+ */
+ ocp {
+ compatible = "ti,omap4-l3-noc", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
+ reg = <0x44000000 0x1000>,
+ <0x44800000 0x2000>,
+ <0x45000000 0x1000>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+
+ l4_wkup: interconnect@4a300000 {
+ };
+
+ l4_cfg: interconnect@4a000000 {
+ };
+
+ l4_per: interconnect@48000000 {
+ };
+
+ l4_abe: interconnect@40100000 {
+ };
+
+ ocmcram: sram@40304000 {
+ compatible = "mmio-sram";
+ reg = <0x40304000 0xa000>; /* 40k */
+ };
+
+ gpmc: gpmc@50000000 {
+ compatible = "ti,omap4430-gpmc";
+ reg = <0x50000000 0x1000>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&sdma 4>;
+ dma-names = "rxtx";
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <4>;
+ ti,hwmods = "gpmc";
+ ti,no-idle-on-init;
+ clocks = <&l3_div_ck>;
+ clock-names = "fck";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ target-module@52000000 {
+ compatible = "ti,sysc-omap4", "ti,sysc";
+ ti,hwmods = "iss";
+ reg = <0x52000000 0x4>,
+ <0x52000010 0x4>;
+ reg-names = "rev", "sysc";
+ ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+ ti,sysc-midle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>,
+ <SYSC_IDLE_SMART_WKUP>;
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>,
+ <SYSC_IDLE_SMART_WKUP>;
+ ti,sysc-delay-us = <2>;
+ clocks = <&iss_clkctrl OMAP4_ISS_CLKCTRL 0>;
+ clock-names = "fck";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x52000000 0x1000000>;
+
+ /* No child device binding, driver in staging */
+ };
+
+ target-module@55082000 {
+ compatible = "ti,sysc-omap2", "ti,sysc";
+ reg = <0x55082000 0x4>,
+ <0x55082010 0x4>,
+ <0x55082014 0x4>;
+ reg-names = "rev", "sysc", "syss";
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>;
+ ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+ SYSC_OMAP2_SOFTRESET |
+ SYSC_OMAP2_AUTOIDLE)>;
+ clocks = <&ducati_clkctrl OMAP4_IPU_CLKCTRL 0>;
+ clock-names = "fck";
+ resets = <&prm_core 2>;
+ reset-names = "rstctrl";
+ ranges = <0x0 0x55082000 0x100>;
+ #size-cells = <1>;
+ #address-cells = <1>;
+
+ mmu_ipu: mmu@0 {
+ compatible = "ti,omap4-iommu";
+ reg = <0x0 0x100>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ #iommu-cells = <0>;
+ ti,iommu-bus-err-back;
+ };
+ };
+
+ target-module@4012c000 {
+ compatible = "ti,sysc-omap4", "ti,sysc";
+ reg = <0x4012c000 0x4>,
+ <0x4012c010 0x4>;
+ reg-names = "rev", "sysc";
+ ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>,
+ <SYSC_IDLE_SMART_WKUP>;
+ clocks = <&abe_clkctrl OMAP4_SLIMBUS1_CLKCTRL 0>;
+ clock-names = "fck";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x00000000 0x4012c000 0x1000>, /* MPU */
+ <0x4902c000 0x4902c000 0x1000>; /* L3 */
+
+ /* No child device binding or driver in mainline */
+ };
+
+ dmm@4e000000 {
+ compatible = "ti,omap4-dmm";
+ reg = <0x4e000000 0x800>;
+ interrupts = <0 113 0x4>;
+ ti,hwmods = "dmm";
+ };
+
+ emif1: emif@4c000000 {
+ compatible = "ti,emif-4d";
+ reg = <0x4c000000 0x100>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "emif1";
+ ti,no-idle-on-init;
+ phy-type = <1>;
+ hw-caps-read-idle-ctrl;
+ hw-caps-ll-interface;
+ hw-caps-temp-alert;
+ };
+
+ emif2: emif@4d000000 {
+ compatible = "ti,emif-4d";
+ reg = <0x4d000000 0x100>;
+ interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "emif2";
+ ti,no-idle-on-init;
+ phy-type = <1>;
+ hw-caps-read-idle-ctrl;
+ hw-caps-ll-interface;
+ hw-caps-temp-alert;
+ };
+
+ aes1_target: target-module@4b501000 {
+ compatible = "ti,sysc-omap2", "ti,sysc";
+ reg = <0x4b501080 0x4>,
+ <0x4b501084 0x4>,
+ <0x4b501088 0x4>;
+ reg-names = "rev", "sysc", "syss";
+ ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+ SYSC_OMAP2_AUTOIDLE)>;
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>,
+ <SYSC_IDLE_SMART_WKUP>;
+ ti,syss-mask = <1>;
+ /* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
+ clocks = <&l4_secure_clkctrl OMAP4_AES1_CLKCTRL 0>;
+ clock-names = "fck";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x4b501000 0x1000>;
+
+ aes1: aes@0 {
+ compatible = "ti,omap4-aes";
+ reg = <0 0xa0>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&sdma 111>, <&sdma 110>;
+ dma-names = "tx", "rx";
+ };
+ };
+
+ aes2_target: target-module@4b701000 {
+ compatible = "ti,sysc-omap2", "ti,sysc";
+ reg = <0x4b701080 0x4>,
+ <0x4b701084 0x4>,
+ <0x4b701088 0x4>;
+ reg-names = "rev", "sysc", "syss";
+ ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+ SYSC_OMAP2_AUTOIDLE)>;
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>,
+ <SYSC_IDLE_SMART_WKUP>;
+ ti,syss-mask = <1>;
+ /* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
+ clocks = <&l4_secure_clkctrl OMAP4_AES2_CLKCTRL 0>;
+ clock-names = "fck";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x4b701000 0x1000>;
+
+ aes2: aes@0 {
+ compatible = "ti,omap4-aes";
+ reg = <0 0xa0>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&sdma 114>, <&sdma 113>;
+ dma-names = "tx", "rx";
+ };
+ };
+
+ sham_target: target-module@4b100000 {
+ compatible = "ti,sysc-omap3-sham", "ti,sysc";
+ reg = <0x4b100100 0x4>,
+ <0x4b100110 0x4>,
+ <0x4b100114 0x4>;
+ reg-names = "rev", "sysc", "syss";
+ ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+ SYSC_OMAP2_AUTOIDLE)>;
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>;
+ ti,syss-mask = <1>;
+ /* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
+ clocks = <&l4_secure_clkctrl OMAP4_SHA2MD5_CLKCTRL 0>;
+ clock-names = "fck";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x4b100000 0x1000>;
+
+ sham: sham@0 {
+ compatible = "ti,omap4-sham";
+ reg = <0 0x300>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&sdma 119>;
+ dma-names = "rx";
+ };
+ };
+
+ abb_mpu: regulator-abb-mpu {
+ compatible = "ti,abb-v2";
+ regulator-name = "abb_mpu";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ ti,tranxdone-status-mask = <0x80>;
+ clocks = <&sys_clkin_ck>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ status = "disabled";
+ };
+
+ abb_iva: regulator-abb-iva {
+ compatible = "ti,abb-v2";
+ regulator-name = "abb_iva";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ ti,tranxdone-status-mask = <0x80000000>;
+ clocks = <&sys_clkin_ck>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ status = "disabled";
+ };
+
+ target-module@56000000 {
+ compatible = "ti,sysc-omap4", "ti,sysc";
+ reg = <0x5600fe00 0x4>,
+ <0x5600fe10 0x4>;
+ reg-names = "rev", "sysc";
+ ti,sysc-midle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>,
+ <SYSC_IDLE_SMART_WKUP>;
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>,
+ <SYSC_IDLE_SMART_WKUP>;
+ clocks = <&l3_gfx_clkctrl OMAP4_GPU_CLKCTRL 0>;
+ clock-names = "fck";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x56000000 0x2000000>;
+
+ /*
+ * Closed source PowerVR driver, no child device
+ * binding or driver in mainline
+ */
+ };
+
+ /*
+ * DSS is only using l3 mapping without l4 as noted in the TRM
+ * "10.1.3 DSS Register Manual" for omap4460.
+ */
+ target-module@58000000 {
+ compatible = "ti,sysc-omap2", "ti,sysc";
+ reg = <0x58000000 4>,
+ <0x58000014 4>;
+ reg-names = "rev", "syss";
+ ti,syss-mask = <1>;
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 0>,
+ <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>,
+ <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>,
+ <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>;
+ clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x58000000 0x1000000>;
+
+ dss: dss@0 {
+ compatible = "ti,omap4-dss";
+ reg = <0 0x80>;
+ status = "disabled";
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
+ clock-names = "fck";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x1000000>;
+
+ target-module@1000 {
+ compatible = "ti,sysc-omap2", "ti,sysc";
+ reg = <0x1000 0x4>,
+ <0x1010 0x4>,
+ <0x1014 0x4>;
+ reg-names = "rev", "sysc", "syss";
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>;
+ ti,sysc-midle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>;
+ ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+ SYSC_OMAP2_ENAWAKEUP |
+ SYSC_OMAP2_SOFTRESET |
+ SYSC_OMAP2_AUTOIDLE)>;
+ ti,syss-mask = <1>;
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
+ <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+ clock-names = "fck", "sys_clk";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1000 0x1000>;
+
+ dispc@0 {
+ compatible = "ti,omap4-dispc";
+ reg = <0 0x1000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
+ clock-names = "fck";
+ };
+ };
+
+ target-module@2000 {
+ compatible = "ti,sysc-omap2", "ti,sysc";
+ reg = <0x2000 0x4>,
+ <0x2010 0x4>,
+ <0x2014 0x4>;
+ reg-names = "rev", "sysc", "syss";
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>;
+ ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+ SYSC_OMAP2_AUTOIDLE)>;
+ ti,syss-mask = <1>;
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
+ <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+ clock-names = "fck", "sys_clk";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x2000 0x1000>;
+
+ rfbi: encoder@0 {
+ reg = <0 0x1000>;
+ status = "disabled";
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, <&l3_div_ck>;
+ clock-names = "fck", "ick";
+ };
+ };
+
+ target-module@3000 {
+ compatible = "ti,sysc-omap2", "ti,sysc";
+ reg = <0x3000 0x4>;
+ reg-names = "rev";
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+ clock-names = "sys_clk";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x3000 0x1000>;
+
+ venc: encoder@0 {
+ compatible = "ti,omap4-venc";
+ reg = <0 0x1000>;
+ status = "disabled";
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>;
+ clock-names = "fck";
+ };
+ };
+
+ target-module@4000 {
+ compatible = "ti,sysc-omap2", "ti,sysc";
+ reg = <0x4000 0x4>,
+ <0x4010 0x4>,
+ <0x4014 0x4>;
+ reg-names = "rev", "sysc", "syss";
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>;
+ ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+ SYSC_OMAP2_ENAWAKEUP |
+ SYSC_OMAP2_SOFTRESET |
+ SYSC_OMAP2_AUTOIDLE)>;
+ ti,syss-mask = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x4000 0x1000>;
+
+ dsi1: encoder@0 {
+ compatible = "ti,omap4-dsi";
+ reg = <0 0x200>,
+ <0x200 0x40>,
+ <0x300 0x20>;
+ reg-names = "proto", "phy", "pll";
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
+ <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+ clock-names = "fck", "sys_clk";
+ };
+ };
+
+ target-module@5000 {
+ compatible = "ti,sysc-omap2", "ti,sysc";
+ reg = <0x5000 0x4>,
+ <0x5010 0x4>,
+ <0x5014 0x4>;
+ reg-names = "rev", "sysc", "syss";
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>,
+ <SYSC_IDLE_SMART>;
+ ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+ SYSC_OMAP2_ENAWAKEUP |
+ SYSC_OMAP2_SOFTRESET |
+ SYSC_OMAP2_AUTOIDLE)>;
+ ti,syss-mask = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x5000 0x1000>;
+
+ dsi2: encoder@0 {
+ compatible = "ti,omap4-dsi";
+ reg = <0 0x200>,
+ <0x200 0x40>,
+ <0x300 0x20>;
+ reg-names = "proto", "phy", "pll";
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
+ <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+ clock-names = "fck", "sys_clk";
+ };
+ };
+
+ target-module@6000 {
+ compatible = "ti,sysc-omap4", "ti,sysc";
+ reg = <0x6000 0x4>,
+ <0x6010 0x4>;
+ reg-names = "rev", "sysc";
+ /*
+ * Has SYSC_IDLE_SMART and SYSC_IDLE_SMART_WKUP
+ * but HDMI audio will fail with them.
+ */
+ ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+ <SYSC_IDLE_NO>;
+ ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>;
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>,
+ <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
+ clock-names = "fck", "dss_clk";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x6000 0x2000>;
+
+ hdmi: encoder@0 {
+ compatible = "ti,omap4-hdmi";
+ reg = <0 0x200>,
+ <0x200 0x100>,
+ <0x300 0x100>,
+ <0x400 0x1000>;
+ reg-names = "wp", "pll", "phy", "core";
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>,
+ <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+ clock-names = "fck", "sys_clk";
+ dmas = <&sdma 76>;
+ dma-names = "audio_tx";
+ };
+ };
+ };
+ };
+ };
+};
+
+#include "omap4-l4.dtsi"
+#include "omap4-l4-abe.dtsi"
+#include "omap44xx-clocks.dtsi"
+
+&prm {
+ prm_tesla: prm@400 {
+ compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+ reg = <0x400 0x100>;
+ #reset-cells = <1>;
+ };
+
+ prm_core: prm@700 {
+ compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+ reg = <0x700 0x100>;
+ #reset-cells = <1>;
+ };
+
+ prm_ivahd: prm@f00 {
+ compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+ reg = <0xf00 0x100>;
+ #reset-cells = <1>;
+ };
+
+ prm_device: prm@1b00 {
+ compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+ reg = <0x1b00 0x40>;
+ #reset-cells = <1>;
+ };
+};