imx: Add support for i.MX28 based XEA board
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
diff --git a/board/liebherr/xea/README b/board/liebherr/xea/README
new file mode 100644
index 0000000..3e55d3e
--- /dev/null
+++ b/board/liebherr/xea/README
@@ -0,0 +1,63 @@
+Building SPL/U-Boot for xea board
+=================================
+
+Setup environment, configure and build, e.g. by:
+
+ $ make imx28_xea_defconfig
+ $ make -j4 u-boot.sb u-boot.img
+
+Now you should see u-boot.sb and u-boot.img files in the build directory.
+
+
+Booting
+=======
+
+The boot ROM loads SPL from SPI NOR flash into SRAM. SPL configures
+DRAM and loads either a Linux kernel (falcon mode) or, if the rescue
+pin is asserted, the main U-Boot. Both kernel and U-Boot reside in
+eMMC boot partition 0. For redundancy, a copy of U-Boot is also
+stored in SPI flash. If a valid kernel image is not found, U-Boot is
+loaded from eMMC or, if this fails, SPI flash.
+
+Boot area layout
+----------------
+
+SPI NOR
+Offset Function File
+------------------------------------------
+0x00000000 SPL u-boot.sb
+0x00010000 U-Boot u-boot.img
+0x00080000 Environment
+
+eMMC
+Offset Function File
+------------------------------------------
+0x00000000 U-Boot u-boot.img
+0x00080000 Devicetree imx28-bttc.dtb
+0x00100000 Kernel uImage
+
+
+Falcon mode
+===========
+
+In falcon mode, the default, SPL loads the kernel and devicetree
+directly. For this to work, the stored devicetree must include
+correct "memory" and "chosen" nodes as these are not updated by SPL
+before booting the kernel.
+
+
+Updating from U-Boot
+====================
+
+The default U-Boot environment includes command sequences to update
+SPL, U-Boot, and kernel over TFTP. These are as follows:
+
+- update_spl: writes u-boot.sb to SPI NOR
+- update_uboot: writes u-boot.img to eMMC and SPI NOR
+- update_kernel: writes kernel and devicetree to eMMC
+
+They can be invoked at the U-Boot prompt using the "run" command,
+e.g. "run update_spl" to update the SPL.
+
+These update commands download the above-named files from the
+${hostname} directory on the server provided by DHCP.