ARM: dts: stih410-b2260: Sync DT with kernel v5.2

Synchronize U-boot DT with kernel v5.2 for stih410-b2260.
Update stih410-b2260-u-boot.dtsi accordingly.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
diff --git a/arch/arm/dts/stih407-clock.dtsi b/arch/arm/dts/stih407-clock.dtsi
index 13029c0..1ab40db 100644
--- a/arch/arm/dts/stih407-clock.dtsi
+++ b/arch/arm/dts/stih407-clock.dtsi
@@ -1,39 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 STMicroelectronics R&D Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 #include <dt-bindings/clock/stih407-clks.h>
 / {
+	/*
+	 * Fixed 30MHz oscillator inputs to SoC
+	 */
+	clk_sysin: clk-sysin {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <30000000>;
+	};
+
+	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
 	clocks {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 
 		/*
-		 * Fixed 30MHz oscillator inputs to SoC
-		 */
-		clk_sysin: clk-sysin {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <30000000>;
-		};
-
-		/*
-		 * ARM Peripheral clock for timers
-		 */
-		arm_periph_clk: clk-m-a9-periphs {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-
-			clocks = <&clk_m_a9>;
-			clock-div = <2>;
-			clock-mult = <1>;
-		};
-
-		/*
 		 * A9 PLL.
 		 */
 		clockgen-a9@92b0000 {
@@ -62,35 +53,22 @@
 				 <&clockgen_a9_pll 0>,
 				 <&clk_s_c0_flexgen 13>,
 				 <&clk_m_a9_ext2f_div2>;
+
+
+			/*
+			 * ARM Peripheral clock for timers
+			 */
+			arm_periph_clk: clk-m-a9-periphs {
+				#clock-cells = <0>;
+				compatible = "fixed-factor-clock";
+
+				clocks = <&clk_m_a9>;
+				clock-div = <2>;
+				clock-mult = <1>;
+			};
 		};
 
-		/*
-		 * ARM Peripheral clock for timers
-		 */
-		clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-
-			clocks = <&clk_s_c0_flexgen 13>;
-
-			clock-output-names = "clk-m-a9-ext2f-div2";
-
-			clock-div = <2>;
-			clock-mult = <1>;
-		};
-
-		/*
-		 * Bootloader initialized system infrastructure clock for
-		 * serial devices.
-		 */
-		clk_ext2f_a9: clockgen-c0@13 {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <200000000>;
-			clock-output-names = "clk-s-icn-reg-0";
-		};
-
-		clockgen-a@090ff000 {
+		clockgen-a@90ff000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x90ff000 0x1000>;
 
@@ -101,6 +79,7 @@
 				clocks = <&clk_sysin>;
 
 				clock-output-names = "clk-s-a0-pll-ofd-0";
+				clock-critical = <0>; /* clk-s-a0-pll-ofd-0 */
 			};
 
 			clk_s_a0_flexgen: clk-s-a0-flexgen {
@@ -112,6 +91,7 @@
 					 <&clk_sysin>;
 
 				clock-output-names = "clk-ic-lmi0";
+				clock-critical = <CLK_IC_LMI0>;
 			};
 		};
 
@@ -126,9 +106,10 @@
 					     "clk-s-c0-fs0-ch1",
 					     "clk-s-c0-fs0-ch2",
 					     "clk-s-c0-fs0-ch3";
+			clock-critical = <0>; /* clk-s-c0-fs0-ch0 */
 		};
 
-		clk_s_c0: clockgen-c@09103000 {
+		clk_s_c0: clockgen-c@9103000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9103000 0x1000>;
 
@@ -139,6 +120,7 @@
 				clocks = <&clk_sysin>;
 
 				clock-output-names = "clk-s-c0-pll0-odf-0";
+				clock-critical = <0>; /* clk-s-c0-pll0-odf-0 */
 			};
 
 			clk_s_c0_pll1: clk-s-c0-pll1 {
@@ -194,6 +176,27 @@
 						     "clk-main-disp",
 						     "clk-aux-disp",
 						     "clk-compo-dvp";
+				clock-critical = <CLK_PROC_STFE>,
+						 <CLK_ICN_CPU>,
+						 <CLK_TX_ICN_DMU>,
+						 <CLK_EXT2F_A9>,
+						 <CLK_ICN_LMI>,
+						 <CLK_ICN_SBC>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+
+					clocks = <&clk_s_c0_flexgen 13>;
+
+					clock-output-names = "clk-m-a9-ext2f-div2";
+
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
 			};
 		};
 
@@ -210,7 +213,7 @@
 					     "clk-s-d0-fs0-ch3";
 		};
 
-		clockgen-d0@09104000 {
+		clockgen-d0@9104000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9104000 0x1000>;
 
@@ -244,13 +247,7 @@
 					     "clk-s-d2-fs0-ch3";
 		};
 
-		clk_tmdsout_hdmi: clk-tmdsout-hdmi {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <0>;
-		};
-
-		clockgen-d2@x9106000 {
+		clockgen-d2@9106000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9106000 0x1000>;
 
diff --git a/arch/arm/dts/stih407-family.dtsi b/arch/arm/dts/stih407-family.dtsi
index 6c6de58..7c36c37 100644
--- a/arch/arm/dts/stih407-family.dtsi
+++ b/arch/arm/dts/stih407-family.dtsi
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 STMicroelectronics Limited.
  * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * publishhed by the Free Software Foundation.
  */
 #include "stih407-pinctrl.dtsi"
 #include <dt-bindings/mfd/st-lpc.h>
@@ -20,7 +17,13 @@
 		#size-cells = <1>;
 		ranges;
 
-		dmu_reserved: rproc@44000000 {
+		gp0_reserved: rproc@45000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x45000000 0x00400000>;
+			no-map;
+		};
+
+		delta_reserved: rproc@44000000 {
 			compatible = "shared-dma-pool";
 			reg = <0x44000000 0x01000000>;
 			no-map;
@@ -47,6 +50,7 @@
 			clocks = <&clk_m_a9>;
 			clock-names = "cpu";
 			clock-latency = <100000>;
+			cpu0-supply = <&pwm_regulator>;
 			st,syscfg = <&syscfg_core 0x8e0>;
 		};
 		cpu@1 {
@@ -65,19 +69,19 @@
 		};
 	};
 
-	intc: interrupt-controller@08761000 {
+	intc: interrupt-controller@8761000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x08761000 0x1000>, <0x08760100 0x100>;
 	};
 
-	scu@08760000 {
+	scu@8760000 {
 		compatible = "arm,cortex-a9-scu";
 		reg = <0x08760000 0x1000>;
 	};
 
-	timer@08760200 {
+	timer@8760200 {
 		interrupt-parent = <&intc>;
 		compatible = "arm,cortex-a9-global-timer";
 		reg = <0x08760200 0x100>;
@@ -85,7 +89,7 @@
 		clocks = <&arm_periph_clk>;
 	};
 
-	l2: cache-controller {
+	l2: cache-controller@8762000 {
 		compatible = "arm,pl310-cache";
 		reg = <0x08762000 0x1000>;
 		arm,data-latency = <3 3 3>;
@@ -118,24 +122,28 @@
 		ranges;
 		compatible = "simple-bus";
 
-		restart {
+		restart: restart-controller@0 {
 			compatible = "st,stih407-restart";
+			reg = <0 0>;
 			st,syscfg = <&syscfg_sbc_reg>;
 			status = "okay";
 		};
 
-		powerdown: powerdown-controller {
+		powerdown: powerdown-controller@0 {
 			compatible = "st,stih407-powerdown";
+			reg = <0 0>;
 			#reset-cells = <1>;
 		};
 
-		softreset: softreset-controller {
+		softreset: softreset-controller@0 {
 			compatible = "st,stih407-softreset";
+			reg = <0 0>;
 			#reset-cells = <1>;
 		};
 
-		picophyreset: picophyreset-controller {
+		picophyreset: picophyreset-controller@0 {
 			compatible = "st,stih407-picophyreset";
+			reg = <0 0>;
 			#reset-cells = <1>;
 		};
 
@@ -167,6 +175,13 @@
 		syscfg_core: core-syscfg@92b0000 {
 			compatible = "st,stih407-core-syscfg", "syscon";
 			reg = <0x92b0000 0x1000>;
+
+			sti_sasg_codec: sti-sasg-codec {
+				compatible = "st,stih407-sas-codec";
+				#sound-dai-cells = <1>;
+				status = "disabled";
+				st,syscfg = <&syscfg_core>;
+			};
 		};
 
 		syscfg_lpm: lpm-syscfg@94b5100 {
@@ -174,8 +189,9 @@
 			reg = <0x94b5100 0x1000>;
 		};
 
-		irq-syscfg {
+		irq-syscfg@0 {
 			compatible    = "st,stih407-irq-syscfg";
+			reg = <0 0>;
 			st,syscfg     = <&syscfg_core>;
 			st,irq-device = <ST_IRQ_SYSCFG_PMU_0>,
 					<ST_IRQ_SYSCFG_PMU_1>;
@@ -187,22 +203,21 @@
 		vtg_main: sti-vtg-main@8d02800 {
 			compatible = "st,vtg";
 			reg = <0x8d02800 0x200>;
-			interrupts = <GIC_SPI 108 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		vtg_aux: sti-vtg-aux@8d00200 {
 			compatible = "st,vtg";
 			reg = <0x8d00200 0x100>;
-			interrupts = <GIC_SPI 109 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		serial@9830000 {
 			compatible = "st,asc";
 			reg = <0x9830000 0x2c>;
-			interrupts = <GIC_SPI 122 IRQ_TYPE_NONE>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_serial0>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			/* Pinctrl moved out to a per-board configuration */
 
 			status = "disabled";
 		};
@@ -210,7 +225,7 @@
 		serial@9831000 {
 			compatible = "st,asc";
 			reg = <0x9831000 0x2c>;
-			interrupts = <GIC_SPI 123 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_serial1>;
 			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
@@ -221,7 +236,7 @@
 		serial@9832000 {
 			compatible = "st,asc";
 			reg = <0x9832000 0x2c>;
-			interrupts = <GIC_SPI 124 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_serial2>;
 			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
@@ -233,7 +248,7 @@
 		sbc_serial0: serial@9530000 {
 			compatible = "st,asc";
 			reg = <0x9530000 0x2c>;
-			interrupts = <GIC_SPI 138 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sbc_serial0>;
 			clocks = <&clk_sysin>;
@@ -244,7 +259,7 @@
 		serial@9531000 {
 			compatible = "st,asc";
 			reg = <0x9531000 0x2c>;
-			interrupts = <GIC_SPI 139 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sbc_serial1>;
 			clocks = <&clk_sysin>;
@@ -374,8 +389,9 @@
 			status = "disabled";
 		};
 
-		usb2_picophy0: phy1 {
+		usb2_picophy0: phy1@0 {
 			compatible = "st,stih407-usb2-phy";
+			reg = <0 0>;
 			#phy-cells = <0>;
 			st,syscfg = <&syscfg_core 0x100 0xf4>;
 			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
@@ -383,12 +399,13 @@
 			reset-names = "global", "port";
 		};
 
-		miphy28lp_phy: miphy28lp@9b22000 {
+		miphy28lp_phy: miphy28lp@0 {
 			compatible = "st,miphy28lp-phy";
 			st,syscfg = <&syscfg_core>;
 			#address-cells	= <1>;
 			#size-cells	= <1>;
 			ranges;
+			reg = <0 0>;
 
 			phy_port0: port@9b22000 {
 				reg = <0x9b22000 0xff>,
@@ -458,6 +475,8 @@
 			clock-names = "ssc";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi1_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 
 			status = "disabled";
 		};
@@ -470,6 +489,8 @@
 			clock-names = "ssc";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi2_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 
 			status = "disabled";
 		};
@@ -482,6 +503,8 @@
 			clock-names = "ssc";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi3_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 
 			status = "disabled";
 		};
@@ -494,6 +517,8 @@
 			clock-names = "ssc";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi4_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 
 			status = "disabled";
 		};
@@ -507,6 +532,8 @@
 			clock-names = "ssc";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi10_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 
 			status = "disabled";
 		};
@@ -519,6 +546,8 @@
 			clock-names = "ssc";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi11_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 
 			status = "disabled";
 		};
@@ -531,16 +560,18 @@
 			clock-names = "ssc";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi12_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 
 			status = "disabled";
 		};
 
-		mmc0: sdhci@09060000 {
+		mmc0: sdhci@9060000 {
 			compatible = "st,sdhci-stih407", "st,sdhci";
 			status = "disabled";
 			reg = <0x09060000 0x7ff>, <0x9061008 0x20>;
 			reg-names = "mmc", "top-mmc-delay";
-			interrupts = <GIC_SPI 92 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "mmcirq";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mmc0>;
@@ -550,12 +581,12 @@
 			bus-width = <8>;
 		};
 
-		mmc1: sdhci@09080000 {
+		mmc1: sdhci@9080000 {
 			compatible = "st,sdhci-stih407", "st,sdhci";
 			status = "disabled";
 			reg = <0x09080000 0x7ff>;
 			reg-names = "mmc";
-			interrupts = <GIC_SPI 90 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "mmcirq";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sd1>;
@@ -563,7 +594,6 @@
 			clocks = <&clk_s_c0_flexgen CLK_MMC_1>,
 				 <&clk_s_c0_flexgen CLK_RX_ICN_HVA>;
 			resets = <&softreset STIH407_MMC1_SOFTRESET>;
-			reset-names = "softreset";
 			bus-width = <4>;
 		};
 
@@ -590,7 +620,7 @@
 			compatible = "st,ahci";
 			reg = <0x9b20000 0x1000>;
 
-			interrupts = <GIC_SPI 159 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hostc";
 
 			phys = <&phy_port0 PHY_TYPE_SATA>;
@@ -613,7 +643,7 @@
 			compatible = "st,ahci";
 			reg = <0x9b28000 0x1000>;
 
-			interrupts = <GIC_SPI 170 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hostc";
 
 			phys = <&phy_port1 PHY_TYPE_SATA>;
@@ -654,11 +684,12 @@
 			dwc3: dwc3@9900000 {
 				compatible	= "snps,dwc3";
 				reg		= <0x09900000 0x100000>;
-				interrupts	= <GIC_SPI 155 IRQ_TYPE_NONE>;
-				dr_mode		= "peripheral";
+				interrupts	= <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode		= "host";
 				phy-names	= "usb2-phy", "usb3-phy";
 				phys		= <&usb2_picophy0>,
 						  <&phy_port2 PHY_TYPE_USB3>;
+				snps,dis_u3_susphy_quirk;
 			};
 		};
 
@@ -667,7 +698,7 @@
 			compatible	= "st,sti-pwm";
 			#pwm-cells	= <2>;
 			reg		= <0x9810000 0x68>;
-			interrupts      = <GIC_SPI 128 IRQ_TYPE_NONE>;
+			interrupts      = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names	= "default";
 			pinctrl-0	= <&pinctrl_pwm0_chan0_default>;
 			clock-names	= "pwm";
@@ -682,6 +713,7 @@
 			compatible	= "st,sti-pwm";
 			#pwm-cells	= <2>;
 			reg		= <0x9510000 0x68>;
+			interrupts      = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names	= "default";
 			pinctrl-0	= <&pinctrl_pwm1_chan0_default
 					&pinctrl_pwm1_chan1_default
@@ -694,14 +726,14 @@
 			status		= "disabled";
 		};
 
-		rng10: rng@08a89000 {
+		rng10: rng@8a89000 {
 			compatible      = "st,rng";
 			reg		= <0x08a89000 0x1000>;
 			clocks          = <&clk_sysin>;
 			status		= "okay";
 		};
 
-		rng11: rng@08a8a000 {
+		rng11: rng@8a8a000 {
 			compatible      = "st,rng";
 			reg		= <0x08a8a000 0x1000>;
 			clocks          = <&clk_sysin>;
@@ -720,8 +752,8 @@
 			resets = <&softreset STIH407_ETH1_SOFTRESET>;
 			reset-names = "stmmaceth";
 
-			interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>,
-				     <GIC_SPI 99 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq", "eth_wake_irq";
 
 			/* DMA Bus Mode */
@@ -735,26 +767,14 @@
 				 <&clk_s_c0_flexgen CLK_ETH_PHY>;
 		};
 
-		cec: sti-cec@094a087c {
-			compatible = "st,stih-cec";
-			reg = <0x94a087c 0x64>;
-			clocks = <&clk_sysin>;
-			clock-names = "cec-clk";
-			interrupts = <GIC_SPI 140 IRQ_TYPE_NONE>;
-			interrupt-names = "cec-irq";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_cec0_default>;
-			resets = <&softreset STIH407_LPM_SOFTRESET>;
-		};
-
-		rng10: rng@08a89000 {
+		rng10: rng@8a89000 {
 			compatible      = "st,rng";
 			reg		= <0x08a89000 0x1000>;
 			clocks          = <&clk_sysin>;
 			status		= "okay";
 		};
 
-		rng11: rng@08a8a000 {
+		rng11: rng@8a8a000 {
 			compatible      = "st,rng";
 			reg		= <0x08a8a000 0x1000>;
 			clocks          = <&clk_sysin>;
@@ -764,7 +784,7 @@
 		mailbox0: mailbox@8f00000  {
 			compatible	= "st,stih407-mailbox";
 			reg		= <0x8f00000 0x1000>;
-			interrupts	= <GIC_SPI 1 IRQ_TYPE_NONE>;
+			interrupts	= <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			#mbox-cells	= <2>;
 			mbox-name	= "a9";
 			status		= "okay";
@@ -794,9 +814,24 @@
 			status		= "okay";
 		};
 
-		st231_delta: st231-delta@44000000 {
+		st231_gp0: st231-gp0@0 {
 			compatible	= "st,st231-rproc";
-			memory-region	= <&dmu_reserved>;
+			reg		= <0 0>;
+			memory-region	= <&gp0_reserved>;
+			resets		= <&softreset STIH407_ST231_GP0_SOFTRESET>;
+			reset-names	= "sw_reset";
+			clocks		= <&clk_s_c0_flexgen CLK_ST231_GP_0>;
+			clock-frequency	= <600000000>;
+			st,syscfg	= <&syscfg_core 0x22c>;
+			#mbox-cells = <1>;
+			mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
+			mboxes = <&mailbox0 0 2>, <&mailbox2 0 1>, <&mailbox0 0 3>, <&mailbox2 0 0>;
+		};
+
+		st231_delta: st231-delta@0 {
+			compatible	= "st,st231-rproc";
+			reg		= <0 0>;
+			memory-region	= <&delta_reserved>;
 			resets		= <&softreset STIH407_ST231_DMU_SOFTRESET>;
 			reset-names	= "sw_reset";
 			clocks		= <&clk_s_c0_flexgen CLK_ST231_DMU>;
@@ -819,7 +854,7 @@
 				 <&clk_s_c0_flexgen CLK_EXT2F_A9>,
 				 <&clk_s_c0_flexgen CLK_EXT2F_A9>,
 				 <&clk_s_c0_flexgen CLK_EXT2F_A9>;
-			interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 			dma-channels = <16>;
 			#dma-cells = <3>;
 		};
@@ -837,9 +872,11 @@
 				<&clk_s_c0_flexgen CLK_TX_ICN_DMU>,
 				<&clk_s_c0_flexgen CLK_EXT2F_A9>;
 
-			interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 			dma-channels = <16>;
 			#dma-cells = <3>;
+
+			status = "disabled";
 		};
 
 		/* fdma free running */
@@ -850,20 +887,15 @@
 			      <0x8e77000 0x1000>,
 			      <0x8e78000 0x8000>;
 			reg-names = "slimcore", "dmem", "peripherals", "imem";
-			interrupts = <GIC_SPI 9 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 			dma-channels = <16>;
 			#dma-cells = <3>;
 			clocks = <&clk_s_c0_flexgen CLK_FDMA>,
 				<&clk_s_c0_flexgen CLK_EXT2F_A9>,
 				<&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
 				<&clk_s_c0_flexgen CLK_EXT2F_A9>;
-		};
 
-		sti_sasg_codec: sti-sasg-codec {
-			compatible = "st,stih407-sas-codec";
-			#sound-dai-cells = <1>;
 			status = "disabled";
-			st,syscfg = <&syscfg_core>;
 		};
 
 		sti_uni_player0: sti-uni-player@8d80000 {
@@ -875,7 +907,7 @@
 			assigned-clock-parents = <0>, <&clk_s_d0_quadfs 0>;
 			assigned-clock-rates = <50000000>;
 			reg = <0x8d80000 0x158>;
-			interrupts = <GIC_SPI 84 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 			dmas = <&fdma0 2 0 1>;
 			dma-names = "tx";
 
@@ -891,7 +923,7 @@
 			assigned-clock-parents = <0>, <&clk_s_d0_quadfs 1>;
 			assigned-clock-rates = <50000000>;
 			reg = <0x8d81000 0x158>;
-			interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
 			dmas = <&fdma0 3 0 1>;
 			dma-names = "tx";
 
@@ -907,7 +939,7 @@
 			assigned-clock-parents = <0>, <&clk_s_d0_quadfs 2>;
 			assigned-clock-rates = <50000000>;
 			reg = <0x8d82000 0x158>;
-			interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			dmas = <&fdma0 4 0 1>;
 			dma-names = "tx";
 
@@ -923,7 +955,7 @@
 			assigned-clock-parents = <0>, <&clk_s_d0_quadfs 3>;
 			assigned-clock-rates = <50000000>;
 			reg = <0x8d85000 0x158>;
-			interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			dmas = <&fdma0 7 0 1>;
 			dma-names = "tx";
 
@@ -935,7 +967,7 @@
 			#sound-dai-cells = <0>;
 			st,syscfg = <&syscfg_core>;
 			reg = <0x8d83000 0x158>;
-			interrupts = <GIC_SPI 87 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
 			dmas = <&fdma0 5 0 1>;
 			dma-names = "rx";
 
@@ -947,32 +979,22 @@
 			#sound-dai-cells = <0>;
 			st,syscfg = <&syscfg_core>;
 			reg = <0x8d84000 0x158>;
-			interrupts = <GIC_SPI 88 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
 			dmas = <&fdma0 6 0 1>;
 			dma-names = "rx";
 
 			status = "disabled";
 		};
 
-		rc: rc@09518000 {
-			compatible = "st,comms-irb";
-			reg = <0x09518000 0x234>;
-			interrupts = <GIC_SPI 132 IRQ_TYPE_NONE>;
-			rx-mode = "infrared";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_ir
-				     &pinctrl_uhf
-				     &pinctrl_tx
-				     &pinctrl_tx_od>;
-			clocks = <&clk_sysin>;
-			resets = <&softreset STIH407_IRB_SOFTRESET>;
-
-			status = "disabled";
-		};
-
-		socinfo {
-			compatible = "st,stih407-socinfo";
-			st,syscfg = <&syscfg_core>;
+		delta0@0 {
+			compatible = "st,st-delta";
+			reg = <0 0>;
+			clock-names = "delta",
+				      "delta-st231",
+				      "delta-flash-promip";
+			clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
+				 <&clk_s_c0_flexgen CLK_ST231_DMU>,
+				 <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
 		};
 	};
 };
diff --git a/arch/arm/dts/stih407-pinctrl.dtsi b/arch/arm/dts/stih407-pinctrl.dtsi
index f27ae21..2cf3357 100644
--- a/arch/arm/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/dts/stih407-pinctrl.dtsi
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 STMicroelectronics Limited.
  * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * publishhed by the Free Software Foundation.
  */
 #include "st-pincfg.h"
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -45,18 +42,18 @@
 	};
 
 	soc {
-		pin-controller-sbc {
+		pin-controller-sbc@961f080 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "st,stih407-sbc-pinctrl";
 			st,syscfg = <&syscfg_sbc>;
 			reg = <0x0961f080 0x4>;
 			reg-names = "irqmux";
-			interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "irqmux";
 			ranges = <0 0x09610000 0x6000>;
 
-			pio0: gpio@09610000 {
+			pio0: gpio@9610000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -64,7 +61,7 @@
 				reg = <0x0 0x100>;
 				st,bank-name = "PIO0";
 			};
-			pio1: gpio@09611000 {
+			pio1: gpio@9611000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -72,7 +69,7 @@
 				reg = <0x1000 0x100>;
 				st,bank-name = "PIO1";
 			};
-			pio2: gpio@09612000 {
+			pio2: gpio@9612000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -80,7 +77,7 @@
 				reg = <0x2000 0x100>;
 				st,bank-name = "PIO2";
 			};
-			pio3: gpio@09613000 {
+			pio3: gpio@9613000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -88,7 +85,7 @@
 				reg = <0x3000 0x100>;
 				st,bank-name = "PIO3";
 			};
-			pio4: gpio@09614000 {
+			pio4: gpio@9614000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -97,7 +94,7 @@
 				st,bank-name = "PIO4";
 			};
 
-			pio5: gpio@09615000 {
+			pio5: gpio@9615000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -369,18 +366,18 @@
 			};
 		};
 
-		pin-controller-front0 {
+		pin-controller-front0@920f080 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "st,stih407-front-pinctrl";
 			st,syscfg = <&syscfg_front>;
 			reg = <0x0920f080 0x4>;
 			reg-names = "irqmux";
-			interrupts = <GIC_SPI 189 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "irqmux";
 			ranges = <0 0x09200000 0x10000>;
 
-			pio10: pio@09200000 {
+			pio10: pio@9200000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -388,7 +385,7 @@
 				reg = <0x0 0x100>;
 				st,bank-name = "PIO10";
 			};
-			pio11: pio@09201000 {
+			pio11: pio@9201000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -396,7 +393,7 @@
 				reg = <0x1000 0x100>;
 				st,bank-name = "PIO11";
 			};
-			pio12: pio@09202000 {
+			pio12: pio@9202000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -404,7 +401,7 @@
 				reg = <0x2000 0x100>;
 				st,bank-name = "PIO12";
 			};
-			pio13: pio@09203000 {
+			pio13: pio@9203000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -412,7 +409,7 @@
 				reg = <0x3000 0x100>;
 				st,bank-name = "PIO13";
 			};
-			pio14: pio@09204000 {
+			pio14: pio@9204000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -420,7 +417,7 @@
 				reg = <0x4000 0x100>;
 				st,bank-name = "PIO14";
 			};
-			pio15: pio@09205000 {
+			pio15: pio@9205000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -428,7 +425,7 @@
 				reg = <0x5000 0x100>;
 				st,bank-name = "PIO15";
 			};
-			pio16: pio@09206000 {
+			pio16: pio@9206000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -436,7 +433,7 @@
 				reg = <0x6000 0x100>;
 				st,bank-name = "PIO16";
 			};
-			pio17: pio@09207000 {
+			pio17: pio@9207000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -444,7 +441,7 @@
 				reg = <0x7000 0x100>;
 				st,bank-name = "PIO17";
 			};
-			pio18: pio@09208000 {
+			pio18: pio@9208000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -452,7 +449,7 @@
 				reg = <0x8000 0x100>;
 				st,bank-name = "PIO18";
 			};
-			pio19: pio@09209000 {
+			pio19: pio@9209000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -465,19 +462,16 @@
 			serial0 {
 				pinctrl_serial0: serial0-0 {
 					st,pins {
-						tx = <&pio17 0 ALT1 OUT>;
-						rx = <&pio17 1 ALT1 IN>;
+						tx =  <&pio17 0 ALT1 OUT>;
+						rx =  <&pio17 1 ALT1 IN>;
 					};
 				};
-				pinctrl_serial0_rts: serial0_rts {
+				pinctrl_serial0_hw_flowctrl: serial0-0_hw_flowctrl {
 					st,pins {
-						rts = <&pio17 3 ALT1 OUT>;
-					};
-				};
-
-				pinctrl_serial0_cts: serial0_cts {
-					st,pins {
+						tx =  <&pio17 0 ALT1 OUT>;
+						rx =  <&pio17 1 ALT1 IN>;
 						cts = <&pio17 2 ALT1 IN>;
+						rts = <&pio17 3 ALT1 OUT>;
 					};
 				};
 			};
@@ -932,18 +926,18 @@
 			};
 		};
 
-		pin-controller-front1 {
+		pin-controller-front1@921f080 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "st,stih407-front-pinctrl";
 			st,syscfg = <&syscfg_front>;
 			reg = <0x0921f080 0x4>;
 			reg-names = "irqmux";
-			interrupts = <GIC_SPI 190 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "irqmux";
 			ranges = <0 0x09210000 0x10000>;
 
-			pio20: pio@09210000 {
+			pio20: pio@9210000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -965,18 +959,18 @@
 			};
 		};
 
-		pin-controller-rear {
+		pin-controller-rear@922f080 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "st,stih407-rear-pinctrl";
 			st,syscfg = <&syscfg_rear>;
 			reg = <0x0922f080 0x4>;
 			reg-names = "irqmux";
-			interrupts = <GIC_SPI 191 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "irqmux";
 			ranges = <0 0x09220000 0x6000>;
 
-			pio30: gpio@09220000 {
+			pio30: gpio@9220000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -984,7 +978,7 @@
 				reg = <0x0 0x100>;
 				st,bank-name = "PIO30";
 			};
-			pio31: gpio@09221000 {
+			pio31: gpio@9221000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -992,7 +986,7 @@
 				reg = <0x1000 0x100>;
 				st,bank-name = "PIO31";
 			};
-			pio32: gpio@09222000 {
+			pio32: gpio@9222000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -1000,7 +994,7 @@
 				reg = <0x2000 0x100>;
 				st,bank-name = "PIO32";
 			};
-			pio33: gpio@09223000 {
+			pio33: gpio@9223000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -1008,7 +1002,7 @@
 				reg = <0x3000 0x100>;
 				st,bank-name = "PIO33";
 			};
-			pio34: gpio@09224000 {
+			pio34: gpio@9224000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -1016,7 +1010,7 @@
 				reg = <0x4000 0x100>;
 				st,bank-name = "PIO34";
 			};
-			pio35: gpio@09225000 {
+			pio35: gpio@9225000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -1026,41 +1020,6 @@
 				st,retime-pin-mask = <0x7f>;
 			};
 
-			dvo {
-				pinctrl_dvo: dvo {
-					st,pins {
-						hs = <&pio30 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						vs = <&pio30 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						de = <&pio30 2 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						ck = <&pio30 3 ALT2 (OE | CLKNOTDATA) 0>;
-						d0 = <&pio30 4 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d1 = <&pio30 5 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d2 = <&pio30 6 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d3 = <&pio30 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d4 = <&pio31 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d5 = <&pio31 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d6 = <&pio31 2 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d7 = <&pio31 3 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d8 = <&pio31 4 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d9 = <&pio31 5 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d10 = <&pio31 6 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d11 = <&pio31 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d12 = <&pio32 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d13 = <&pio32 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d14 = <&pio32 2 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d15 = <&pio32 3 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d16 = <&pio32 4 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d17 = <&pio32 5 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d18 = <&pio32 6 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d19 = <&pio32 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d20 = <&pio33 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d21 = <&pio33 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d22 = <&pio33 2 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-						d23 = <&pio33 3 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-					};
-				};
-			};
-
 			i2c4 {
 				pinctrl_i2c4_default: i2c4-default {
 					st,pins {
@@ -1195,18 +1154,18 @@
 			};
 		};
 
-		pin-controller-flash {
+		pin-controller-flash@923f080 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "st,stih407-flash-pinctrl";
 			st,syscfg = <&syscfg_flash>;
 			reg = <0x0923f080 0x4>;
 			reg-names = "irqmux";
-			interrupts = <GIC_SPI 192 IRQ_TYPE_NONE>;
-			interrupts-names = "irqmux";
+			interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "irqmux";
 			ranges = <0 0x09230000 0x3000>;
 
-			pio40: gpio@09230000 {
+			pio40: gpio@9230000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -1214,7 +1173,7 @@
 				reg = <0 0x100>;
 				st,bank-name = "PIO40";
 			};
-			pio41: gpio@09231000 {
+			pio41: gpio@9231000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -1222,7 +1181,7 @@
 				reg = <0x1000 0x100>;
 				st,bank-name = "PIO41";
 			};
-			pio42: gpio@09232000 {
+			pio42: gpio@9232000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
diff --git a/arch/arm/dts/stih410-b2260-u-boot.dtsi b/arch/arm/dts/stih410-b2260-u-boot.dtsi
index 8391631..897c421 100644
--- a/arch/arm/dts/stih410-b2260-u-boot.dtsi
+++ b/arch/arm/dts/stih410-b2260-u-boot.dtsi
@@ -9,8 +9,25 @@
 	soc {
 		st_dwc3: dwc3@8f94000 {
 			dwc3: dwc3@9900000 {
+				dr_mode	= "peripheral";
 				phys = <&usb2_picophy0>;
 			};
 		};
+
+		ohci0: usb@9a03c00 {
+			compatible = "generic-ohci";
+		};
+
+		ehci0: usb@9a03e00 {
+			compatible = "generic-ehci";
+		};
+
+		ohci1: usb@9a83c00 {
+			compatible = "generic-ohci";
+		};
+
+		ehci1: usb@9a83e00 {
+			compatible = "generic-ehci";
+		};
 	};
 };
diff --git a/arch/arm/dts/stih410-b2260.dts b/arch/arm/dts/stih410-b2260.dts
index 54250e2..4fbd8e9 100644
--- a/arch/arm/dts/stih410-b2260.dts
+++ b/arch/arm/dts/stih410-b2260.dts
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2016 STMicroelectronics (R&D) Limited.
  * Author: Patrice Chotard <patrice.chotard@st.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 /dts-v1/;
 #include "stih410.dtsi"
@@ -15,68 +12,79 @@
 	compatible = "st,stih410-b2260", "st,stih410";
 
 	chosen {
-		bootargs = "console=ttyAS1,115200";
-		linux,stdout-path = &uart1;
+		bootargs = "clk_ignore_unused";
 		stdout-path = &uart1;
 	};
 
-	memory {
+	memory@40000000 {
 		device_type = "memory";
 		reg = <0x40000000 0x40000000>;
 	};
 
 	aliases {
-		ttyAS1 = &uart1;
+		serial1 = &uart1;
 		ethernet0 = &ethernet0;
 	};
 
-	soc {
-
-		leds {
-			compatible = "gpio-leds";
-			user_green_1 {
-				label = "User_green_1";
-				gpios = <&pio1 3 GPIO_ACTIVE_LOW>;
-				linux,default-trigger = "heartbeat";
-				default-state = "off";
-			};
-
-			user_green_2 {
-				label = "User_green_2";
-				gpios = <&pio4 1 GPIO_ACTIVE_LOW>;
-				default-state = "off";
-			};
-
-			user_green_3 {
-				label = "User_green_3";
-				gpios = <&pio2 1 GPIO_ACTIVE_LOW>;
-				default-state = "off";
-			};
-
-			user_green_4 {
-				label = "User_green_4";
-				gpios = <&pio2 5 GPIO_ACTIVE_LOW>;
-				default-state = "off";
-			};
-
-			wifi_yellow {
-				label = "Wifi_yellow";
-				gpios = <&pio4 0 GPIO_ACTIVE_LOW>;
-				linux,default-trigger = "wifi-activity";
-				default-state = "off";
-			};
-
-			bt_blue {
-				label = "Bluetooth_blue";
-				gpios = <&pio3 3 GPIO_ACTIVE_LOW>;
-				linux,default-trigger = "hci0-power";
-				default-state = "off";
-			};
+	leds {
+		compatible = "gpio-leds";
+		user_green_1 {
+			label = "User_green_1";
+			gpios = <&pio1 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
 		};
 
+		user_green_2 {
+			label = "User_green_2";
+			gpios = <&pio4 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		user_green_3 {
+			label = "User_green_3";
+			gpios = <&pio2 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		user_green_4 {
+			label = "User_green_4";
+			gpios = <&pio2 5 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "STI-B2260";
+		status = "okay";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+			/* DAC */
+			format = "i2s";
+			mclk-fs = <128>;
+			cpu {
+				sound-dai = <&sti_uni_player0>;
+			};
+
+			codec {
+				sound-dai = <&sti_hdmi>;
+			};
+		};
+	};
+
+	soc {
 		/* Low speed expansion connector */
 		uart0: serial@9830000 {
 			label = "LS-UART0";
+			pinctrl-names = "default", "no-hw-flowctrl";
+			pinctrl-0 = <&pinctrl_serial0_hw_flowctrl>;
+			pinctrl-1 = <&pinctrl_serial0>;
+			rts-gpios = <&pio17 3 GPIO_ACTIVE_LOW>;
+			uart-has-rtscts;
 			status = "okay";
 		};
 
@@ -119,14 +127,14 @@
 			status = "okay";
 		};
 
-		mmc0: sdhci@09060000 {
+		mmc0: sdhci@9060000 {
 			pinctrl-0 = <&pinctrl_sd0>;
 			bus-width = <4>;
 			status = "okay";
 		};
 
 		/* high speed expansion connector */
-		mmc1: sdhci@09080000 {
+		mmc1: sdhci@9080000 {
 			status = "okay";
 		};
 
@@ -138,11 +146,11 @@
 			status = "okay";
 		};
 
-		usb2_picophy1: phy2 {
+		usb2_picophy1: phy2@0 {
 			status = "okay";
 		};
 
-		usb2_picophy2: phy3 {
+		usb2_picophy2: phy3@0 {
 			status = "okay";
 		};
 
@@ -183,17 +191,17 @@
 		sti_uni_player0: sti-uni-player@8d80000 {
 			status = "okay";
 		};
-
 		/* SSC11 to HDMI */
 		hdmiddc: i2c@9541000 {
 			/* HDMI V1.3a supports Standard mode only */
 			clock-frequency = <100000>;
 			st,i2c-min-scl-pulse-width-us = <0>;
-			st,i2c-min-sda-pulse-width-us = <1>;
+			st,i2c-min-sda-pulse-width-us = <5>;
 			status = "okay";
 		};
 
-		miphy28lp_phy: miphy28lp@9b22000 {
+		miphy28lp_phy: miphy28lp@0 {
+
 			phy_port1: port@9b2a000 {
 				st,osc-force-ext;
 			};
@@ -202,25 +210,5 @@
 		sata1: sata@9b28000 {
 			status = "okay";
 		};
-
-		sound {
-			compatible = "simple-audio-card";
-			simple-audio-card,name = "STI-B2260";
-			status = "okay";
-
-			simple-audio-card,dai-link@0 {
-				/* DAC */
-				format = "i2s";
-				mclk-fs = <128>;
-				cpu {
-					sound-dai = <&sti_uni_player0>;
-				};
-
-				codec {
-					sound-dai = <&sti_hdmi>;
-				};
-			};
-		};
-
 	};
 };
diff --git a/arch/arm/dts/stih410-clock.dtsi b/arch/arm/dts/stih410-clock.dtsi
index 8598eff..81a8c25 100644
--- a/arch/arm/dts/stih410-clock.dtsi
+++ b/arch/arm/dts/stih410-clock.dtsi
@@ -1,12 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 STMicroelectronics R&D Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 #include <dt-bindings/clock/stih410-clks.h>
 / {
+	/*
+	 * Fixed 30MHz oscillator inputs to SoC
+	 */
+	clk_sysin: clk-sysin {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <30000000>;
+		clock-output-names = "CLK_SYSIN";
+	};
+
+	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
 	clocks {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -15,27 +28,6 @@
 		compatible = "st,stih410-clk", "simple-bus";
 
 		/*
-		 * Fixed 30MHz oscillator inputs to SoC
-		 */
-		clk_sysin: clk-sysin {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <30000000>;
-			clock-output-names = "CLK_SYSIN";
-		};
-
-		/*
-		 * ARM Peripheral clock for timers
-		 */
-		arm_periph_clk: clk-m-a9-periphs {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clocks = <&clk_m_a9>;
-			clock-div = <2>;
-			clock-mult = <1>;
-		};
-
-		/*
 		 * A9 PLL.
 		 */
 		clockgen-a9@92b0000 {
@@ -64,35 +56,19 @@
 				 <&clockgen_a9_pll 0>,
 				 <&clk_s_c0_flexgen 13>,
 				 <&clk_m_a9_ext2f_div2>;
+			/*
+			 * ARM Peripheral clock for timers
+			 */
+			arm_periph_clk: clk-m-a9-periphs {
+				#clock-cells = <0>;
+				compatible = "fixed-factor-clock";
+				clocks = <&clk_m_a9>;
+				clock-div = <2>;
+				clock-mult = <1>;
+			};
 		};
 
-		/*
-		 * ARM Peripheral clock for timers
-		 */
-		clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-
-			clocks = <&clk_s_c0_flexgen 13>;
-
-			clock-output-names = "clk-m-a9-ext2f-div2";
-
-			clock-div = <2>;
-			clock-mult = <1>;
-		};
-
-		/*
-		 * Bootloader initialized system infrastructure clock for
-		 * serial devices.
-		 */
-		clk_ext2f_a9: clockgen-c0@13 {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <200000000>;
-			clock-output-names = "clk-s-icn-reg-0";
-		};
-
-		clockgen-a@090ff000 {
+		clockgen-a@90ff000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x90ff000 0x1000>;
 
@@ -134,7 +110,7 @@
 			clock-critical = <0>; /* clk-s-c0-fs0-ch0 */
 		};
 
-		clk_s_c0: clockgen-c@09103000 {
+		clk_s_c0: clockgen-c@9103000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9103000 0x1000>;
 
@@ -208,11 +184,27 @@
 						     "clk-clust-hades",
 						     "clk-hwpe-hades",
 						     "clk-fc-hades";
-				clock-critical = <CLK_ICN_CPU>,
+				clock-critical = <CLK_PROC_STFE>,
+						 <CLK_ICN_CPU>,
 						 <CLK_TX_ICN_DMU>,
 						 <CLK_EXT2F_A9>,
 						 <CLK_ICN_LMI>,
 						 <CLK_ICN_SBC>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+
+					clocks = <&clk_s_c0_flexgen 13>;
+
+					clock-output-names = "clk-m-a9-ext2f-div2";
+
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
 			};
 		};
 
@@ -229,7 +221,7 @@
 					     "clk-s-d0-fs0-ch3";
 		};
 
-		clockgen-d0@09104000 {
+		clockgen-d0@9104000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9104000 0x1000>;
 
@@ -265,13 +257,7 @@
 					     "clk-s-d2-fs0-ch3";
 		};
 
-		clk_tmdsout_hdmi: clk-tmdsout-hdmi {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <0>;
-		};
-
-		clockgen-d2@x9106000 {
+		clockgen-d2@9106000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9106000 0x1000>;
 
diff --git a/arch/arm/dts/stih410-pinctrl.dtsi b/arch/arm/dts/stih410-pinctrl.dtsi
index b3e9dfc..e6eadd1 100644
--- a/arch/arm/dts/stih410-pinctrl.dtsi
+++ b/arch/arm/dts/stih410-pinctrl.dtsi
@@ -1,16 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 STMicroelectronics Limited.
  * Author: Peter Griffin <peter.griffin@linaro.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * publishhed by the Free Software Foundation.
  */
 #include "st-pincfg.h"
 / {
 
 	soc {
-		pin-controller-rear {
+		pin-controller-rear@922f080 {
 
 			usb0 {
 				pinctrl_usb0: usb2-0 {
diff --git a/arch/arm/dts/stih410.dtsi b/arch/arm/dts/stih410.dtsi
index b59b110..6d84701 100644
--- a/arch/arm/dts/stih410.dtsi
+++ b/arch/arm/dts/stih410.dtsi
@@ -1,67 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 STMicroelectronics Limited.
  * Author: Peter Griffin <peter.griffin@linaro.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * publishhed by the Free Software Foundation.
  */
 #include "stih410-clock.dtsi"
 #include "stih407-family.dtsi"
 #include "stih410-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 / {
 	aliases {
 		bdisp0 = &bdisp0;
 	};
 
-	cpus {
-		cpu@0 {
-			st,syscfg = <&syscfg_core 0x8e0>;
-			st,syscfg-eng = <&syscfg_opp 0x4 0x0>;
-			clocks = <&clk_m_a9>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-		cpu@1 {
-			clocks = <&clk_m_a9>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-	};
-
-	cpu0_opp_table: opp_table0 {
-		compatible = "operating-points-v2";
-		opp-shared;
-
-		opp@1500000000 {
-			opp-supported-hw = <0xffffffff  0xffffffff  0xffffffff>;
-			opp-hz = /bits/ 64 <1500000000>;
-			clock-latency-ns = <10000000>;
-			opp-suspend;
-		};
-		opp@1200000000 {
-			opp-supported-hw = <0xffffffff  0xffffffff  0xffffffff>;
-			opp-hz = /bits/ 64 <1200000000>;
-			clock-latency-ns = <10000000>;
-		};
-		opp@800000000 {
-			opp-supported-hw = <0xffffffff  0xffffffff  0xffffffff>;
-			opp-hz = /bits/ 64 <800000000>;
-			clock-latency-ns = <10000000>;
-		};
-		opp@400000000 {
-			opp-supported-hw = <0xffffffff  0xffffffff  0xffffffff>;
-			opp-hz = /bits/ 64 <400000000>;
-			clock-latency-ns = <10000000>;
-		};
-	};
-
 	soc {
-		syscfg_opp: @08a6583c {
-			compatible = "syscon";
-			reg = <0x08a6583c 0x8>;
-		};
-
-		usb2_picophy1: phy2 {
+		usb2_picophy1: phy2@0 {
 			compatible = "st,stih407-usb2-phy";
+			reg = <0 0>;
 			#phy-cells = <0>;
 			st,syscfg = <&syscfg_core 0xf8 0xf4>;
 			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
@@ -71,8 +25,9 @@
 			status = "disabled";
 		};
 
-		usb2_picophy2: phy3 {
+		usb2_picophy2: phy3@0 {
 			compatible = "st,stih407-usb2-phy";
+			reg = <0 0>;
 			#phy-cells = <0>;
 			st,syscfg = <&syscfg_core 0xfc 0xf4>;
 			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
@@ -83,15 +38,14 @@
 		};
 
 		ohci0: usb@9a03c00 {
-			compatible = "generic-ohci";
+			compatible = "st,st-ohci-300x";
 			reg = <0x9a03c00 0x100>;
-			interrupts = <GIC_SPI 180 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
 				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT0_SOFTRESET>;
 			reset-names = "power", "softreset";
-
 			phys = <&usb2_picophy1>;
 			phy-names = "usb";
 
@@ -99,9 +53,9 @@
 		};
 
 		ehci0: usb@9a03e00 {
-			compatible = "generic-ehci";
+			compatible = "st,st-ehci-300x";
 			reg = <0x9a03e00 0x100>;
-			interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
 			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
@@ -116,15 +70,14 @@
 		};
 
 		ohci1: usb@9a83c00 {
-			compatible = "generic-ohci";
+			compatible = "st,st-ohci-300x";
 			reg = <0x9a83c00 0x100>;
-			interrupts = <GIC_SPI 181 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
 				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
 			reset-names = "power", "softreset";
-
 			phys = <&usb2_picophy2>;
 			phy-names = "usb";
 
@@ -132,9 +85,9 @@
 		};
 
 		ehci1: usb@9a83e00 {
-			compatible = "generic-ehci";
+			compatible = "st,st-ehci-300x";
 			reg = <0x9a83e00 0x100>;
-			interrupts = <GIC_SPI 153 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
 			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
@@ -142,18 +95,18 @@
 			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
 			reset-names = "power", "softreset";
-
 			phys = <&usb2_picophy2>;
 			phy-names = "usb";
 
 			status = "disabled";
 		};
 
-		sti-display-subsystem {
+		sti-display-subsystem@0 {
 			compatible = "st,sti-display-subsystem";
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			reg = <0 0>;
 			assigned-clocks	= <&clk_s_d2_quadfs 0>,
 					  <&clk_s_d2_quadfs 1>,
 					  <&clk_s_c0_pll1 0>,
@@ -243,10 +196,10 @@
 
 			sti_hdmi: sti-hdmi@8d04000 {
 				compatible = "st,stih407-hdmi";
-				#sound-dai-cells = <0>;
 				reg = <0x8d04000 0x1000>;
 				reg-names = "hdmi-reg";
-				interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
+				#sound-dai-cells = <0>;
+				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names	= "irq";
 				clock-names = "pix",
 					      "tmds",
@@ -262,7 +215,7 @@
 					 <&clk_s_d2_quadfs 0>,
 					 <&clk_s_d2_quadfs 1>;
 
-				hdmi,hpd-gpio = <&pio5 3>;
+				hdmi,hpd-gpio = <&pio5 3 GPIO_ACTIVE_LOW>;
 				reset-names = "hdmi";
 				resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
 				ddc = <&hdmiddc>;
@@ -283,24 +236,7 @@
 					 <&clk_s_d2_quadfs 1>;
 			};
 
-			sti-dvo@8d00400 {
-				compatible = "st,stih407-dvo";
-				status = "disabled";
-				reg = <0x8d00400 0x200>;
-				reg-names = "dvo-reg";
-				clock-names = "dvo_pix",
-					      "dvo",
-					      "main_parent",
-					      "aux_parent";
-				clocks = <&clk_s_d2_flexgen CLK_PIX_DVO>,
-					 <&clk_s_d2_flexgen CLK_DVO>,
-					 <&clk_s_d2_quadfs 0>,
-					 <&clk_s_d2_quadfs 1>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_dvo>;
-			};
-
-			sti-hqvdp@9c000000 {
+			sti-hqvdp@9c00000 {
 				compatible = "st,stih407-hqvdp";
 				reg = <0x9C00000 0x100000>;
 				clock-names = "hqvdp", "pix_main";
@@ -315,7 +251,7 @@
 		bdisp0:bdisp@9f10000 {
 			compatible = "st,stih407-bdisp";
 			reg = <0x9f10000 0x1000>;
-			interrupts = <GIC_SPI 38 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "bdisp";
 			clocks = <&clk_s_c0_flexgen CLK_IC_BDISP_0>;
 		};
@@ -324,8 +260,8 @@
 			compatible = "st,st-hva";
 			reg = <0x8c85000 0x400>, <0x6000000 0x40000>;
 			reg-names = "hva_registers", "hva_esram";
-			interrupts = <GIC_SPI 58 IRQ_TYPE_NONE>,
-				     <GIC_SPI 59 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "clk_hva";
 			clocks = <&clk_s_c0_flexgen CLK_HVA>;
 		};
@@ -338,66 +274,7 @@
 			interrupts = <GIC_SPI 205 IRQ_TYPE_EDGE_RISING>;
 		};
 
-		g1@8c80000 {
-			compatible = "st,g1";
-			reg = <0x8c80000 0x194>;
-			interrupts = <GIC_SPI 57 IRQ_TYPE_NONE>;
-		};
-
-		temp0{
-			compatible = "st,stih407-thermal";
-			reg = <0x91a0000 0x28>;
-			clock-names = "thermal";
-			clocks = <&clk_sysin>;
-			interrupts = <GIC_SPI 205 IRQ_TYPE_EDGE_RISING>;
-		};
-
-		delta0 {
-			compatible = "st,delta";
-			clock-names = "delta", "delta-st231", "delta-flash-promip";
-			clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
-			    <&clk_s_c0_flexgen CLK_ST231_DMU>,
-			    <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
-		};
-
-		h264pp0: h264pp@8c00000 {
-			compatible = "st,h264pp";
-			reg = <0x8c00000 0x20000>;
-			interrupts = <GIC_SPI 53 IRQ_TYPE_NONE>;
-			clock-names = "clk_h264pp_0";
-			clocks = <&clk_s_c0_flexgen CLK_PP_DMU>;
-		};
-
-		mali: mali@09f00000 {
-			compatible	= "arm,mali-400";
-			reg		= <0x09f00000 0x10000>;
-			interrupts	= <GIC_SPI 49 IRQ_TYPE_NONE>,
-					  <GIC_SPI 50 IRQ_TYPE_NONE>,
-					  <GIC_SPI 41 IRQ_TYPE_NONE>,
-					  <GIC_SPI 45 IRQ_TYPE_NONE>,
-					  <GIC_SPI 42 IRQ_TYPE_NONE>,
-					  <GIC_SPI 46 IRQ_TYPE_NONE>,
-					  <GIC_SPI 43 IRQ_TYPE_NONE>,
-					  <GIC_SPI 47 IRQ_TYPE_NONE>,
-					  <GIC_SPI 44 IRQ_TYPE_NONE>,
-					  <GIC_SPI 48 IRQ_TYPE_NONE>;
-			interrupt-names = "IRQGP",
-					  "IRQGPMMU",
-					  "IRQPP0",
-					  "IRQPPMMU0",
-					  "IRQPP1",
-					  "IRQPPMMU1",
-					  "IRQPP2",
-					  "IRQPPMMU2",
-					  "IRQPP3",
-					  "IRQPPMMU3";
-			clock-names	= "gpu-clk";
-			clocks		= <&clk_s_c0_flexgen CLK_ICN_GPU>;
-			reset-names	= "gpu";
-			resets		= <&softreset STIH407_GPU_SOFTRESET>;
-		};
-
-		delta0 {
+		delta0@0 {
 			compatible = "st,st-delta";
 			clock-names = "delta",
 				      "delta-st231",
@@ -407,51 +284,17 @@
 				 <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
 		};
 
-		h264pp0: h264pp@8c00000 {
-			compatible = "st,h264pp";
-			reg = <0x8c00000 0x20000>;
-			interrupts = <GIC_SPI 53 IRQ_TYPE_NONE>;
-			clock-names = "clk_h264pp_0";
-			clocks = <&clk_s_c0_flexgen CLK_PP_DMU>;
-		};
-
-		mali: mali@09f00000 {
-			compatible	= "arm,mali-400";
-			reg		= <0x09f00000 0x10000>;
-			interrupts	= <GIC_SPI 49 IRQ_TYPE_NONE>,
-					  <GIC_SPI 50 IRQ_TYPE_NONE>,
-					  <GIC_SPI 41 IRQ_TYPE_NONE>,
-					  <GIC_SPI 45 IRQ_TYPE_NONE>,
-					  <GIC_SPI 42 IRQ_TYPE_NONE>,
-					  <GIC_SPI 46 IRQ_TYPE_NONE>,
-					  <GIC_SPI 43 IRQ_TYPE_NONE>,
-					  <GIC_SPI 47 IRQ_TYPE_NONE>,
-					  <GIC_SPI 44 IRQ_TYPE_NONE>,
-					  <GIC_SPI 48 IRQ_TYPE_NONE>;
-			interrupt-names = "IRQGP",
-					  "IRQGPMMU",
-					  "IRQPP0",
-					  "IRQPPMMU0",
-					  "IRQPP1",
-					  "IRQPPMMU1",
-					  "IRQPP2",
-					  "IRQPPMMU2",
-					  "IRQPP3",
-					  "IRQPPMMU3";
-			clock-names	= "gpu-clk";
-			clocks		= <&clk_s_c0_flexgen CLK_ICN_GPU>;
-			reset-names	= "gpu";
-			resets		= <&softreset STIH407_GPU_SOFTRESET>;
-		};
-
-		hva@8c85000{
-			compatible = "st,st-hva";
-			reg = <0x8c85000 0x400>, <0x6000000 0x40000>;
-			reg-names = "hva_registers", "hva_esram";
-			interrupts = <GIC_SPI 58 IRQ_TYPE_NONE>,
-				     <GIC_SPI 59 IRQ_TYPE_NONE>;
-			clock-names = "clk_hva";
-			clocks = <&clk_s_c0_flexgen CLK_HVA>;
+		sti-cec@94a087c {
+			compatible = "st,stih-cec";
+			reg = <0x94a087c 0x64>;
+			clocks = <&clk_sysin>;
+			clock-names = "cec-clk";
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cec-irq";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_cec0_default>;
+			resets = <&softreset STIH407_LPM_SOFTRESET>;
+			hdmi-phandle = <&sti_hdmi>;
 		};
 	};
 };