dm: mmc: Remove use of fdtdec GPIO support
These functions are going away, so use the new uclass support instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
diff --git a/drivers/mmc/tegra_mmc.c b/drivers/mmc/tegra_mmc.c
index 2bd36b0..2cd8cf1 100644
--- a/drivers/mmc/tegra_mmc.c
+++ b/drivers/mmc/tegra_mmc.c
@@ -515,8 +515,8 @@
debug("tegra_mmc_getcd called\n");
- if (fdt_gpio_isvalid(&host->cd_gpio))
- return fdtdec_get_gpio(&host->cd_gpio);
+ if (dm_gpio_is_valid(&host->cd_gpio))
+ return dm_gpio_get_value(&host->cd_gpio);
return 1;
}
@@ -531,7 +531,6 @@
static int do_mmc_init(int dev_index)
{
struct mmc_host *host;
- char gpusage[12]; /* "SD/MMCn PWR" or "SD/MMCn CD" */
struct mmc *mmc;
/* DT should have been read & host config filled in */
@@ -539,27 +538,15 @@
if (!host->enabled)
return -1;
- debug(" do_mmc_init: index %d, bus width %d "
- "pwr_gpio %d cd_gpio %d\n",
- dev_index, host->width,
- host->pwr_gpio.gpio, host->cd_gpio.gpio);
+ debug(" do_mmc_init: index %d, bus width %d pwr_gpio %d cd_gpio %d\n",
+ dev_index, host->width, gpio_get_number(&host->pwr_gpio),
+ gpio_get_number(&host->cd_gpio));
host->clock = 0;
clock_start_periph_pll(host->mmc_id, CLOCK_ID_PERIPH, 20000000);
- if (fdt_gpio_isvalid(&host->pwr_gpio)) {
- sprintf(gpusage, "SD/MMC%d PWR", dev_index);
- gpio_request(host->pwr_gpio.gpio, gpusage);
- gpio_direction_output(host->pwr_gpio.gpio, 1);
- debug(" Power GPIO name = %s\n", host->pwr_gpio.name);
- }
-
- if (fdt_gpio_isvalid(&host->cd_gpio)) {
- sprintf(gpusage, "SD/MMC%d CD", dev_index);
- gpio_request(host->cd_gpio.gpio, gpusage);
- gpio_direction_input(host->cd_gpio.gpio);
- debug(" CD GPIO name = %s\n", host->cd_gpio.name);
- }
+ if (dm_gpio_is_valid(&host->pwr_gpio))
+ dm_gpio_set_value(&host->pwr_gpio, 1);
memset(&host->cfg, 0, sizeof(host->cfg));
@@ -626,9 +613,12 @@
debug("%s: no sdmmc width found\n", __func__);
/* These GPIOs are optional */
- fdtdec_decode_gpio(blob, node, "cd-gpios", &host->cd_gpio);
- fdtdec_decode_gpio(blob, node, "wp-gpios", &host->wp_gpio);
- fdtdec_decode_gpio(blob, node, "power-gpios", &host->pwr_gpio);
+ gpio_request_by_name_nodev(blob, node, "cd-gpios", 0, &host->cd_gpio,
+ GPIOD_IS_IN);
+ gpio_request_by_name_nodev(blob, node, "wp-gpios", 0, &host->wp_gpio,
+ GPIOD_IS_IN);
+ gpio_request_by_name_nodev(blob, node, "power-gpios", 0,
+ &host->pwr_gpio, GPIOD_IS_OUT);
debug("%s: found controller at %p, width = %d, periph_id = %d\n",
__func__, host->reg, host->width, host->mmc_id);