ARM: add devicetree files for kirkwood SoC
These files are taken verbatim from the Linux kernel 4.17
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/arch/arm/dts/kirkwood-6192.dtsi b/arch/arm/dts/kirkwood-6192.dtsi
new file mode 100644
index 0000000..396bcba
--- /dev/null
+++ b/arch/arm/dts/kirkwood-6192.dtsi
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+ mbus@f1000000 {
+ pciec: pcie@82000000 {
+ compatible = "marvell,kirkwood-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>;
+
+ pcie0: pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ bus-range = <0x00 0xff>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 9>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gate_clk 2>;
+ status = "disabled";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ compatible = "marvell,88f6192-pinctrl";
+
+ pmx_sata0: pmx-sata0 {
+ marvell,pins = "mpp5", "mpp21", "mpp23";
+ marvell,function = "sata0";
+ };
+ pmx_sata1: pmx-sata1 {
+ marvell,pins = "mpp4", "mpp20", "mpp22";
+ marvell,function = "sata1";
+ };
+ pmx_sdio: pmx-sdio {
+ marvell,pins = "mpp12", "mpp13", "mpp14",
+ "mpp15", "mpp16", "mpp17";
+ marvell,function = "sdio";
+ };
+ };
+
+ rtc: rtc@10300 {
+ compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
+ reg = <0x10300 0x20>;
+ interrupts = <53>;
+ clocks = <&gate_clk 7>;
+ };
+
+ sata: sata@80000 {
+ compatible = "marvell,orion-sata";
+ reg = <0x80000 0x5000>;
+ interrupts = <21>;
+ clocks = <&gate_clk 14>, <&gate_clk 15>;
+ clock-names = "0", "1";
+ phys = <&sata_phy0>, <&sata_phy1>;
+ phy-names = "port0", "port1";
+ status = "disabled";
+ };
+
+ sdio: mvsdio@90000 {
+ compatible = "marvell,orion-sdio";
+ reg = <0x90000 0x200>;
+ interrupts = <28>;
+ clocks = <&gate_clk 4>;
+ bus-width = <4>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/dts/kirkwood-6281.dtsi b/arch/arm/dts/kirkwood-6281.dtsi
new file mode 100644
index 0000000..faa0584
--- /dev/null
+++ b/arch/arm/dts/kirkwood-6281.dtsi
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+ mbus@f1000000 {
+ pciec: pcie@82000000 {
+ compatible = "marvell,kirkwood-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>;
+
+ pcie0: pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ bus-range = <0x00 0xff>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 9>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gate_clk 2>;
+ status = "disabled";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ compatible = "marvell,88f6281-pinctrl";
+
+ pmx_sata0: pmx-sata0 {
+ marvell,pins = "mpp5", "mpp21", "mpp23";
+ marvell,function = "sata0";
+ };
+ pmx_sata1: pmx-sata1 {
+ marvell,pins = "mpp4", "mpp20", "mpp22";
+ marvell,function = "sata1";
+ };
+ pmx_sdio: pmx-sdio {
+ marvell,pins = "mpp12", "mpp13", "mpp14",
+ "mpp15", "mpp16", "mpp17";
+ marvell,function = "sdio";
+ };
+ };
+
+ rtc: rtc@10300 {
+ compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
+ reg = <0x10300 0x20>;
+ interrupts = <53>;
+ clocks = <&gate_clk 7>;
+ };
+
+ sata: sata@80000 {
+ compatible = "marvell,orion-sata";
+ reg = <0x80000 0x5000>;
+ interrupts = <21>;
+ clocks = <&gate_clk 14>, <&gate_clk 15>;
+ clock-names = "0", "1";
+ phys = <&sata_phy0>, <&sata_phy1>;
+ phy-names = "port0", "port1";
+ status = "disabled";
+ };
+
+ sdio: mvsdio@90000 {
+ compatible = "marvell,orion-sdio";
+ reg = <0x90000 0x200>;
+ interrupts = <28>;
+ clocks = <&gate_clk 4>;
+ pinctrl-0 = <&pmx_sdio>;
+ pinctrl-names = "default";
+ bus-width = <4>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/dts/kirkwood-98dx4122.dtsi b/arch/arm/dts/kirkwood-98dx4122.dtsi
new file mode 100644
index 0000000..299c147
--- /dev/null
+++ b/arch/arm/dts/kirkwood-98dx4122.dtsi
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+ mbus@f1000000 {
+ pciec: pcie@82000000 {
+ compatible = "marvell,kirkwood-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>;
+
+ pcie0: pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ bus-range = <0x00 0xff>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 9>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gate_clk 2>;
+ status = "disabled";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ compatible = "marvell,98dx4122-pinctrl";
+
+ };
+ };
+};
+
+&sata_phy0 {
+ status = "disabled";
+};
+
+&sata_phy1 {
+ status = "disabled";
+};
diff --git a/arch/arm/dts/kirkwood.dtsi b/arch/arm/dts/kirkwood.dtsi
new file mode 100644
index 0000000..81c7eda
--- /dev/null
+++ b/arch/arm/dts/kirkwood.dtsi
@@ -0,0 +1,393 @@
+// SPDX-License-Identifier: GPL-2.0
+/include/ "skeleton.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+/ {
+ compatible = "marvell,kirkwood";
+ interrupt-parent = <&intc>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "marvell,feroceon";
+ reg = <0>;
+ clocks = <&core_clk 1>, <&core_clk 3>, <&gate_clk 11>;
+ clock-names = "cpu_clk", "ddrclk", "powersave";
+ };
+ };
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ i2c0 = &i2c0;
+ };
+
+ mbus@f1000000 {
+ compatible = "marvell,kirkwood-mbus", "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* If a board file needs to change this ranges it must replace it completely */
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */
+ MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */
+ MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */
+ >;
+ controller = <&mbusc>;
+ pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */
+ pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */
+
+ nand: nand@12f {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cle = <0>;
+ ale = <1>;
+ bank-width = <1>;
+ compatible = "marvell,orion-nand";
+ reg = <MBUS_ID(0x01, 0x2f) 0 0x400>;
+ chip-delay = <25>;
+ /* set partition map and/or chip-delay in board dts */
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ crypto_sram: sa-sram@301 {
+ compatible = "mmio-sram";
+ reg = <MBUS_ID(0x03, 0x01) 0x0 0x800>;
+ clocks = <&gate_clk 17>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+
+ ocp@f1000000 {
+ compatible = "simple-bus";
+ ranges = <0x00000000 0xf1000000 0x0100000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ pinctrl: pin-controller@10000 {
+ /* set compatible property in SoC file */
+ reg = <0x10000 0x20>;
+
+ pmx_ge1: pmx-ge1 {
+ marvell,pins = "mpp20", "mpp21", "mpp22", "mpp23",
+ "mpp24", "mpp25", "mpp26", "mpp27",
+ "mpp30", "mpp31", "mpp32", "mpp33";
+ marvell,function = "ge1";
+ };
+
+ pmx_nand: pmx-nand {
+ marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3",
+ "mpp4", "mpp5", "mpp18", "mpp19";
+ marvell,function = "nand";
+ };
+
+ /*
+ * Default SPI0 pinctrl setting with CSn on mpp0,
+ * overwrite marvell,pins on board level if required.
+ */
+ pmx_spi: pmx-spi {
+ marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3";
+ marvell,function = "spi";
+ };
+
+ pmx_twsi0: pmx-twsi0 {
+ marvell,pins = "mpp8", "mpp9";
+ marvell,function = "twsi0";
+ };
+
+ /*
+ * Default UART pinctrl setting without RTS/CTS,
+ * overwrite marvell,pins on board level if required.
+ */
+ pmx_uart0: pmx-uart0 {
+ marvell,pins = "mpp10", "mpp11";
+ marvell,function = "uart0";
+ };
+
+ pmx_uart1: pmx-uart1 {
+ marvell,pins = "mpp13", "mpp14";
+ marvell,function = "uart1";
+ };
+ };
+
+ core_clk: core-clocks@10030 {
+ compatible = "marvell,kirkwood-core-clock";
+ reg = <0x10030 0x4>;
+ #clock-cells = <1>;
+ };
+
+ spi0: spi@10600 {
+ compatible = "marvell,orion-spi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ interrupts = <23>;
+ reg = <0x10600 0x28>;
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_spi>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ gpio0: gpio@10100 {
+ compatible = "marvell,orion-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x10100 0x40>;
+ ngpios = <32>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <35>, <36>, <37>, <38>;
+ clocks = <&gate_clk 7>;
+ };
+
+ gpio1: gpio@10140 {
+ compatible = "marvell,orion-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x10140 0x40>;
+ ngpios = <18>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <39>, <40>, <41>;
+ clocks = <&gate_clk 7>;
+ };
+
+ i2c0: i2c@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <29>;
+ clock-frequency = <100000>;
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_twsi0>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ uart0: serial@12000 {
+ compatible = "ns16550a";
+ reg = <0x12000 0x100>;
+ reg-shift = <2>;
+ interrupts = <33>;
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_uart0>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ uart1: serial@12100 {
+ compatible = "ns16550a";
+ reg = <0x12100 0x100>;
+ reg-shift = <2>;
+ interrupts = <34>;
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_uart1>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ mbusc: mbus-controller@20000 {
+ compatible = "marvell,mbus-controller";
+ reg = <0x20000 0x80>, <0x1500 0x20>;
+ };
+
+ sysc: system-controller@20000 {
+ compatible = "marvell,orion-system-controller";
+ reg = <0x20000 0x120>;
+ };
+
+ bridge_intc: bridge-interrupt-ctrl@20110 {
+ compatible = "marvell,orion-bridge-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x20110 0x8>;
+ interrupts = <1>;
+ marvell,#interrupts = <6>;
+ };
+
+ gate_clk: clock-gating-control@2011c {
+ compatible = "marvell,kirkwood-gating-clock";
+ reg = <0x2011c 0x4>;
+ clocks = <&core_clk 0>;
+ #clock-cells = <1>;
+ };
+
+ l2: l2-cache@20128 {
+ compatible = "marvell,kirkwood-cache";
+ reg = <0x20128 0x4>;
+ };
+
+ intc: main-interrupt-ctrl@20200 {
+ compatible = "marvell,orion-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x20200 0x10>, <0x20210 0x10>;
+ };
+
+ timer: timer@20300 {
+ compatible = "marvell,orion-timer";
+ reg = <0x20300 0x20>;
+ interrupt-parent = <&bridge_intc>;
+ interrupts = <1>, <2>;
+ clocks = <&core_clk 0>;
+ };
+
+ wdt: watchdog-timer@20300 {
+ compatible = "marvell,orion-wdt";
+ reg = <0x20300 0x28>, <0x20108 0x4>;
+ interrupt-parent = <&bridge_intc>;
+ interrupts = <3>;
+ clocks = <&gate_clk 7>;
+ status = "okay";
+ };
+
+ cesa: crypto@30000 {
+ compatible = "marvell,kirkwood-crypto";
+ reg = <0x30000 0x10000>;
+ reg-names = "regs";
+ interrupts = <22>;
+ clocks = <&gate_clk 17>;
+ marvell,crypto-srams = <&crypto_sram>;
+ marvell,crypto-sram-size = <0x800>;
+ status = "okay";
+ };
+
+ usb0: ehci@50000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x50000 0x1000>;
+ interrupts = <19>;
+ clocks = <&gate_clk 3>;
+ status = "okay";
+ };
+
+ dma0: xor@60800 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60800 0x100
+ 0x60A00 0x100>;
+ status = "okay";
+ clocks = <&gate_clk 8>;
+
+ xor00 {
+ interrupts = <5>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor01 {
+ interrupts = <6>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
+
+ dma1: xor@60900 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60900 0x100
+ 0x60B00 0x100>;
+ status = "okay";
+ clocks = <&gate_clk 16>;
+
+ xor00 {
+ interrupts = <7>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor01 {
+ interrupts = <8>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
+
+ eth0: ethernet-controller@72000 {
+ compatible = "marvell,kirkwood-eth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72000 0x4000>;
+ clocks = <&gate_clk 0>;
+ marvell,tx-checksum-limit = <1600>;
+ status = "disabled";
+
+ eth0port: ethernet0-port@0 {
+ compatible = "marvell,kirkwood-eth-port";
+ reg = <0>;
+ interrupts = <11>;
+ /* overwrite MAC address in bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ /* set phy-handle property in board file */
+ };
+ };
+
+ mdio: mdio-bus@72004 {
+ compatible = "marvell,orion-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72004 0x84>;
+ interrupts = <46>;
+ clocks = <&gate_clk 0>;
+ status = "disabled";
+
+ /* add phy nodes in board file */
+ };
+
+ eth1: ethernet-controller@76000 {
+ compatible = "marvell,kirkwood-eth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76000 0x4000>;
+ clocks = <&gate_clk 19>;
+ marvell,tx-checksum-limit = <1600>;
+ pinctrl-0 = <&pmx_ge1>;
+ pinctrl-names = "default";
+ status = "disabled";
+
+ eth1port: ethernet1-port@0 {
+ compatible = "marvell,kirkwood-eth-port";
+ reg = <0>;
+ interrupts = <15>;
+ /* overwrite MAC address in bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ /* set phy-handle property in board file */
+ };
+ };
+
+ sata_phy0: sata-phy@82000 {
+ compatible = "marvell,mvebu-sata-phy";
+ reg = <0x82000 0x0334>;
+ clocks = <&gate_clk 14>;
+ clock-names = "sata";
+ #phy-cells = <0>;
+ status = "ok";
+ };
+
+ sata_phy1: sata-phy@84000 {
+ compatible = "marvell,mvebu-sata-phy";
+ reg = <0x84000 0x0334>;
+ clocks = <&gate_clk 15>;
+ clock-names = "sata";
+ #phy-cells = <0>;
+ status = "ok";
+ };
+
+ audio0: audio-controller@a0000 {
+ compatible = "marvell,kirkwood-audio";
+ #sound-dai-cells = <0>;
+ reg = <0xa0000 0x2210>;
+ interrupts = <24>;
+ clocks = <&gate_clk 9>;
+ clock-names = "internal";
+ status = "disabled";
+ };
+ };
+};