Kconfig: Move TEXT_BASE et al under general setup
These don't relate to booting. Move them out of there and into the same
place as the other related settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/Kconfig b/Kconfig
index 0a2e975..2d4b821 100644
--- a/Kconfig
+++ b/Kconfig
@@ -585,6 +585,71 @@
This provides an option to bringup different processors
in multiprocessor cases.
+config HAVE_TEXT_BASE
+ bool
+ depends on !NIOS2 && !XTENSA
+ depends on !EFI_APP
+ default y
+
+config TEXT_BASE
+ depends on HAVE_TEXT_BASE
+ default 0x0 if POSITION_INDEPENDENT
+ default 0x80800000 if ARCH_OMAP2PLUS || ARCH_K3
+ default 0x81700000 if MACH_SUNIV
+ default 0x2a000000 if MACH_SUN9I
+ default 0x4a000000 if SUNXI_MINIMUM_DRAM_MB >= 256
+ default 0x42e00000 if SUNXI_MINIMUM_DRAM_MB >= 64
+ hex "Text Base"
+ help
+ The address in memory that U-Boot will be running from, initially.
+
+config HAVE_SYS_MONITOR_BASE
+ bool
+ depends on ARC || MIPS || M68K || NIOS2 || PPC || XTENSA || X86 \
+ || ENV_IS_IN_FLASH || MTD_NOR_FLASH
+ depends on !EFI_APP
+ default y
+
+config SYS_MONITOR_BASE
+ depends on HAVE_SYS_MONITOR_BASE
+ hex "Physical start address of boot monitor code"
+ default TEXT_BASE
+ help
+ The physical start address of boot monitor code (which is the same as
+ CONFIG_TEXT_BASE when linking) and the same as CFG_SYS_FLASH_BASE
+ when booting from flash.
+
+config SPL_SYS_MONITOR_BASE
+ depends on MPC85xx && SPL && HAVE_SYS_MONITOR_BASE
+ hex "Physical start address of SPL monitor code"
+ default SPL_TEXT_BASE
+
+config TPL_SYS_MONITOR_BASE
+ depends on MPC85xx && TPL && HAVE_SYS_MONITOR_BASE
+ hex "Physical start address of TPL monitor code"
+
+config DYNAMIC_SYS_CLK_FREQ
+ bool "Determine CPU clock frequency at run-time"
+ help
+ Implement a get_board_sys_clk function that will determine the CPU
+ clock frequency at run time, rather than define it statically.
+
+config SYS_CLK_FREQ
+ depends on !DYNAMIC_SYS_CLK_FREQ
+ int "CPU clock frequency"
+ default 125000000 if ARCH_LS1012A
+ default 100000000 if ARCH_P2020 || ARCH_T1024 || ARCH_T1042 || \
+ ARCH_LS1021A || FSL_LSCH2 || FSL_LSCH3
+ default 66666666 if ARCH_P1010 || ARCH_P1020 || ARCH_T4240
+ default 66660000 if ARCH_T2080
+ default 33333333 if RCAR_GEN3
+ default 24000000 if ARCH_EXYNOS
+ default 20000000 if RCAR_GEN2
+ default 0
+ help
+ A static value for the CPU frequency. Note that if not required
+ for a given SoC, this can be left at 0.
+
source "api/Kconfig"
endmenu # General setup