* Avoid flicker on the TRAB's VFD by synchronizing the enable with
the HSYNC/VSYNC. Requires new CPLD code (Version 101 for Rev. 100
boards, version 153 for Rev. 200 boards).
* Patch by Vladimir Gurevich, 12 Mar 2003:
Fix relocation problem of statically initialized string pointers
in common/cmd_pci.c
* Patch by Kai-Uwe Blöm, 12 Mar 2003:
Cleanup & bug fixes for JFFS2 code:
- the memory mangement was broken. It caused havoc on malloc by
writing beyond the block boundaries.
- the length calculation for files was wrong, sometimes resulting
in short file reads.
- data copying now optionally takes fragment version numbers into
account, to avoid copying from older data.
See doc/README.JFFS2 for details.
diff --git a/board/trab/vfd.c b/board/trab/vfd.c
index 894e315..9b61f6e 100644
--- a/board/trab/vfd.c
+++ b/board/trab/vfd.c
@@ -59,10 +59,24 @@
#define FRAME_BUF_SIZE ((256*4*56)/8)
#define frame_buf_offs 4
+/* defines for starting Timer3 as CPLD-Clk */
+#define START3 (1 << 16)
+#define UPDATE3 (1 << 17)
+#define INVERT3 (1 << 18)
+#define RELOAD3 (1 << 19)
+
+/* CPLD-Register for controlling vfd-blank-signal */
+#define VFD_DISABLE (*(volatile uchar *)0x04038000=0x0000)
+#define VFD_ENABLE (*(volatile uchar *)0x04038000=0x0001)
+
/* Supported VFD Types */
#define VFD_TYPE_T119C 1 /* Noritake T119C VFD */
#define VFD_TYPE_MN11236 2
+/*#define NEW_CPLD_CLK*/
+
+int vfd_board_id;
+
/* taken from armboot/common/vfd.c */
unsigned long adr_vfd_table[112][18][2][4][2];
unsigned char bit_vfd_table[112][18][2][4][2];
@@ -80,9 +94,7 @@
/*
* clear frame buffer (logical clear => set to "black")
*/
- memset ((void *)(gd->fb_base),
- gd->vfd_inv_data ? 0xFF : 0,
- FRAME_BUF_SIZE);
+ memset ((void *)(gd->fb_base), 0, FRAME_BUF_SIZE);
switch (gd->vfd_type) {
case VFD_TYPE_T119C:
@@ -98,10 +110,7 @@
bit_nr = bit % 8;
bit_nr = (bit_nr > 3) ? bit_nr-4 : bit_nr+4;
temp=(*(volatile unsigned char*)(adr));
- if (gd->vfd_inv_data)
- temp &= ~(1<<bit_nr);
- else
- temp |= (1<<bit_nr);
+ temp |= (1<<bit_nr);
(*(volatile unsigned char*)(adr))=temp;
if(grid_cycle<55)
@@ -115,10 +124,7 @@
bit_nr = bit%8;
bit_nr = (bit_nr>3)?bit_nr-4:bit_nr+4;
temp=(*(volatile unsigned char*)(adr));
- if (gd->vfd_inv_data)
- temp &= ~(1<<bit_nr);
- else
- temp |= (1<<bit_nr);
+ temp |= (1<<bit_nr);
(*(volatile unsigned char*)(adr))=temp;
}
}
@@ -136,10 +142,7 @@
bit_nr = bit % 8;
bit_nr = (bit_nr > 3) ? bit_nr-4 : bit_nr+4;
temp=(*(volatile unsigned char*)(adr));
- if (gd->vfd_inv_data)
- temp &= ~(1<<bit_nr);
- else
- temp |= (1<<bit_nr);
+ temp |= (1<<bit_nr);
(*(volatile unsigned char*)(adr))=temp;
if(grid_cycle<37)
@@ -152,10 +155,7 @@
bit_nr = bit%8;
bit_nr = (bit_nr>3)?bit_nr-4:bit_nr+4;
temp=(*(volatile unsigned char*)(adr));
- if (gd->vfd_inv_data)
- temp &= ~(1<<bit_nr);
- else
- temp |= (1<<bit_nr);
+ temp |= (1<<bit_nr);
(*(volatile unsigned char*)(adr))=temp;
}
}
@@ -250,7 +250,7 @@
for(entry=0;entry<2;entry++) {
unsigned long adr = gd->fb_base;
unsigned int bit_nr = 0;
-
+
if (vfd_table[x][y][color][display][entry]) {
pixel = vfd_table[x][y][color][display][entry] + frame_buf_offs;
@@ -295,18 +295,11 @@
bit_nr = bit_vfd_table[x][y][color][display][0];
temp=(*(volatile unsigned char*)(adr));
- if (gd->vfd_inv_data) {
- if (value)
- temp &= ~(1<<bit_nr);
- else
- temp |= (1<<bit_nr);
- } else {
- if (value)
- temp |= (1<<bit_nr);
- else
- temp &= ~(1<<bit_nr);
- }
-
+ if (value)
+ temp |= (1<<bit_nr);
+ else
+ temp &= ~(1<<bit_nr);
+
(*(volatile unsigned char*)(adr))=temp;
}
@@ -363,22 +356,59 @@
* This function initializes VFD clock that is needed for the CPLD that
* manages the keyboard.
*/
-int vfd_init_clocks(void)
+int vfd_init_clocks (void)
{
- /* Port-Pins als LCD-Ausgang */
- rPCCON = (rPCCON & 0xFFFFFF00)| 0x000000AA;
- /* Port-Pins als LCD-Ausgang */
- rPDCON = (rPDCON & 0xFFFFFF03)| 0x000000A8;
-#ifdef CFG_WITH_VFRAME
- /* mit VFRAME zum Messen */
- rPDCON = (rPDCON & 0xFFFFFF00)| 0x000000AA;
-#endif
- rLCDCON2 = 0x000DC000;
- rLCDCON3 = 0x0051000A;
- rLCDCON4 = 0x00000001;
- rLCDCON5 = 0x00000440;
+ /* try to determine display type from the value
+ * defined by pull-ups
+ */
+ rPCUP = (rPCUP & 0xFFF0); /* activate GPC0...GPC3 pullups */
+ rPCCON = (rPCCON & 0xFFFFFF00); /* configure GPC0...GPC3 as inputs */
+ udelay (10); /* allow signals to settle */
+ vfd_board_id = (~rPCDAT) & 0x000F; /* read GPC0...GPC3 port pins */
+
+ VFD_DISABLE; /* activate blank for the vfd */
+
+#define NEW_CPLD_CLK
+
+#ifdef NEW_CPLD_CLK
+ if (vfd_board_id) {
+ /* If new board revision, then use PWM 3 as cpld-clock */
+ /* Enable 500 Hz timer for fill level sensor to operate properly */
+ /* Configure TOUT3 as functional pin, disable pull-up */
+ rPDCON &= ~0x30000;
+ rPDCON |= 0x20000;
+ rPDUP |= (1 << 8);
+
+ /* Configure the prescaler */
+ rTCFG0 &= ~0xff00;
+ rTCFG0 |= 0x0f00;
+
+ /* Select MUX input (divider) for timer3 (1/16) */
+ rTCFG1 &= ~0xf000;
+ rTCFG1 |= 0x3000;
+
+ /* Enable autoreload and set the counter and compare
+ * registers to values for the 500 Hz clock
+ * (for a given prescaler (15) and divider (16)):
+ * counter = (66000000 / 500) >> 9;
+ */
+ rTCNTB3 = 0x101;
+ rTCMPB3 = 0x101 / 2;
+
+ /* Start timer */
+ rTCON = (rTCON | UPDATE3 | RELOAD3) & ~INVERT3;
+ rTCON = (rTCON | START3) & ~UPDATE3;
+ }
+#endif
+ /* If old board revision, then use vm-signal as cpld-clock */
+ rLCDCON2 = 0x00FFC000;
+ rLCDCON3 = 0x0007FF00;
+ rLCDCON4 = 0x00000000;
+ rLCDCON5 = 0x00000400;
rLCDCON1 = 0x00000B75;
+ /* VM (GPD1) is used as clock for the CPLD */
+ rPDCON = (rPDCON & 0xFFFFFFF3) | 0x00000008;
return 0;
}
@@ -397,7 +427,7 @@
char *tmp;
ulong palette;
static int vfd_init_done = 0;
- int vfd_id;
+ int vfd_inv_data = 0;
DECLARE_GLOBAL_DATA_PTR;
@@ -405,17 +435,9 @@
return (0);
vfd_init_done = 1;
- /* try to determine display type from the value
- * defined by pull-ups
- */
- rPCUP = (rPCUP & 0xFFF0); /* activate GPC0...GPC3 pullups */
- rPCCON = (rPCCON & 0xFFFFFF00); /* configure GPC0...GPC3 as inputs */
- udelay(10); /* allow signals to settle */
+ debug("Detecting Revison of WA4-VFD: ID=0x%X\n", vfd_board_id);
- vfd_id = (~rPCDAT) & 0x000F; /* read GPC0...GPC3 port pins */
- debug("Detecting Revison of WA4-VFD: ID=0x%X\n", vfd_id);
-
- switch (vfd_id) {
+ switch (vfd_board_id) {
case 0: /* board revision < Rev.200 */
if ((tmp = getenv ("vfd_type")) == NULL) {
break;
@@ -428,19 +450,18 @@
/* cannot use printf for a warning here */
gd->vfd_type = 0; /* unknown */
}
- gd->vfd_inv_data = 0;
break;
default: /* default to MN11236, data inverted */
gd->vfd_type = VFD_TYPE_MN11236;
- gd->vfd_inv_data = 1;
+ vfd_inv_data = 1;
setenv ("vfd_type", "MN11236");
}
debug ("VFD type: %s%s\n",
(gd->vfd_type == VFD_TYPE_T119C) ? "T119C" :
(gd->vfd_type == VFD_TYPE_MN11236) ? "MN11236" :
"unknown",
- gd->vfd_inv_data ? ", inverted data" : "");
+ vfd_inv_data ? ", inverted data" : "");
gd->fb_base = gd->fb_base;
create_vfd_table();
@@ -458,11 +479,33 @@
* (wrap around)
* see manual S3C2400
*/
+ /* Stopp LCD-Controller */
+ rLCDCON1 = 0x00000000;
/* frame buffer startadr */
rLCDSADDR1 = gd->fb_base >> 1;
/* frame buffer endadr */
rLCDSADDR2 = (gd->fb_base + FRAME_BUF_SIZE) >> 1;
rLCDSADDR3 = ((256/4));
+ rLCDCON2 = 0x000DC000;
+ rLCDCON3 = 0x0051000A;
+ rLCDCON4 = 0x00000001;
+ if (gd->vfd_type && vfd_inv_data)
+ rLCDCON5 = 0x000004C0;
+ else
+ rLCDCON5 = 0x00000440;
+
+ /* Port pins as LCD output */
+ rPCCON = (rPCCON & 0xFFFFFF00)| 0x000000AA;
+ rPDCON = (rPDCON & 0xFFFFFF03)| 0x000000A8;
+
+ /* Synchronize VFD enable with LCD controller to avoid flicker */
+ rLCDCON1 = 0x00000B75; /* Start LCD-Controller */
+ while((rLCDCON5 & 0x180000)!=0x100000); /* Wait for end of VSYNC */
+ while((rLCDCON5 & 0x060000)!=0x040000); /* Wait for next HSYNC */
+ while((rLCDCON5 & 0x060000)==0x040000);
+ while((rLCDCON5 & 0x060000)!=0x000000);
+ if(gd->vfd_type)
+ VFD_ENABLE;
debug ("LCDSADDR1: %lX\n", rLCDSADDR1);
debug ("LCDSADDR2: %lX\n", rLCDSADDR2);
@@ -471,6 +514,17 @@
return 0;
}
+/*
+ * Disable VFD: should be run before resetting the system:
+ * disable VM, enable pull-up
+ */
+void disable_vfd (void)
+{
+ VFD_DISABLE;
+ rPDCON &= ~0xC;
+ rPDUP &= ~0x2;
+}
+
/************************************************************************/
/* ** ROM capable initialization part - needed to reserve FB memory */
/************************************************************************/