ARM: stm32: use clock setup function defined in clock.c
Use the clock setup function defined in clock.c instead of setting the
clock bits directly in the drivers.
Remove register definitions of RCC in rcc.h as these are already
defined in the struct in stm32.h
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
diff --git a/arch/arm/include/asm/arch-stm32f7/rcc.h b/arch/arm/include/asm/arch-stm32f7/rcc.h
index 184c366..23eec5e 100644
--- a/arch/arm/include/asm/arch-stm32f7/rcc.h
+++ b/arch/arm/include/asm/arch-stm32f7/rcc.h
@@ -8,32 +8,6 @@
#ifndef _STM32_RCC_H
#define _STM32_RCC_H
-#define RCC_CR 0x00 /* clock control */
-#define RCC_PLLCFGR 0x04 /* PLL configuration */
-#define RCC_CFGR 0x08 /* clock configuration */
-#define RCC_CIR 0x0C /* clock interrupt */
-#define RCC_AHB1RSTR 0x10 /* AHB1 peripheral reset */
-#define RCC_AHB2RSTR 0x14 /* AHB2 peripheral reset */
-#define RCC_AHB3RSTR 0x18 /* AHB3 peripheral reset */
-#define RCC_APB1RSTR 0x20 /* APB1 peripheral reset */
-#define RCC_APB2RSTR 0x24 /* APB2 peripheral reset */
-#define RCC_AHB1ENR 0x30 /* AHB1 peripheral clock enable */
-#define RCC_AHB2ENR 0x34 /* AHB2 peripheral clock enable */
-#define RCC_AHB3ENR 0x38 /* AHB3 peripheral clock enable */
-#define RCC_APB1ENR 0x40 /* APB1 peripheral clock enable */
-#define RCC_APB2ENR 0x44 /* APB2 peripheral clock enable */
-#define RCC_AHB1LPENR 0x50 /* periph clk enable in low pwr mode */
-#define RCC_AHB2LPENR 0x54 /* AHB2 periph clk enable in low pwr mode */
-#define RCC_AHB3LPENR 0x58 /* AHB3 periph clk enable in low pwr mode */
-#define RCC_APB1LPENR 0x60 /* APB1 periph clk enable in low pwr mode */
-#define RCC_APB2LPENR 0x64 /* APB2 periph clk enable in low pwr mode */
-#define RCC_BDCR 0x70 /* Backup domain control */
-#define RCC_CSR 0x74 /* clock control & status */
-#define RCC_SSCGR 0x80 /* spread spectrum clock generation */
-#define RCC_PLLI2SCFGR 0x84 /* PLLI2S configuration */
-#define RCC_PLLSAICFG 0x88 /* PLLSAI configuration */
-#define RCC_DCKCFG1 0x8C /* dedicated clocks configuration register */
-#define RCC_DCKCFG2 0x90 /* dedicated clocks configuration register */
/*
* RCC AHB1ENR specific definitions
*/
diff --git a/arch/arm/include/asm/arch-stm32f7/stm32_periph.h b/arch/arm/include/asm/arch-stm32f7/stm32_periph.h
index 38adc4e..9b315a8 100644
--- a/arch/arm/include/asm/arch-stm32f7/stm32_periph.h
+++ b/arch/arm/include/asm/arch-stm32f7/stm32_periph.h
@@ -33,6 +33,9 @@
GPIO_I_CLOCK_CFG,
GPIO_J_CLOCK_CFG,
GPIO_K_CLOCK_CFG,
+ SYSCFG_CLOCK_CFG,
+ TIMER2_CLOCK_CFG,
+ FMC_CLOCK_CFG,
};
#endif /* __ASM_ARM_ARCH_PERIPH_H */
diff --git a/arch/arm/mach-stm32/stm32f7/clock.c b/arch/arm/mach-stm32/stm32f7/clock.c
index 8091c74..4faf174 100644
--- a/arch/arm/mach-stm32/stm32f7/clock.c
+++ b/arch/arm/mach-stm32/stm32f7/clock.c
@@ -252,6 +252,15 @@
case GPIO_K_CLOCK_CFG:
setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_K_EN);
break;
+ case SYSCFG_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->apb2enr, RCC_APB2ENR_SYSCFGEN);
+ break;
+ case TIMER2_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_TIM2EN);
+ break;
+ case FMC_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_FMC_EN);
+ break;
default:
break;
}
diff --git a/arch/arm/mach-stm32/stm32f7/timer.c b/arch/arm/mach-stm32/stm32f7/timer.c
index a7dee10..c15f8bb 100644
--- a/arch/arm/mach-stm32/stm32f7/timer.c
+++ b/arch/arm/mach-stm32/stm32f7/timer.c
@@ -8,8 +8,8 @@
#include <common.h>
#include <asm/io.h>
#include <asm/arch/stm32.h>
+#include <asm/arch/stm32_defs.h>
#include <asm/arch/gpt.h>
-#include <asm/arch/rcc.h>
#define READ_TIMER() (readl(&gpt1_regs_ptr->cnt) & GPT_FREE_RUNNING)
#define GPT_RESOLUTION (CONFIG_SYS_HZ_CLOCK/CONFIG_STM32_HZ)
@@ -22,7 +22,7 @@
int timer_init(void)
{
/* Timer2 clock configuration */
- setbits_le32(RCC_BASE + RCC_APB1ENR, RCC_APB1ENR_TIM2EN);
+ clock_setup(TIMER2_CLOCK_CFG);
/* Stop the timer */
writel(readl(&gpt1_regs_ptr->cr1) & ~GPT_CR1_CEN, &gpt1_regs_ptr->cr1);