sbc8548: use I/O accessors
Sweep throught the board specific file and replace the various
register proddings with the equivalent I/O accessors.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/board/sbc8548/sbc8548.c b/board/sbc8548/sbc8548.c
index 96a5f42..ce998e1 100644
--- a/board/sbc8548/sbc8548.c
+++ b/board/sbc8548/sbc8548.c
@@ -56,15 +56,15 @@
volatile u_char *rev= (void *)CONFIG_SYS_BD_REV;
printf ("Board: Wind River SBC8548 Rev. 0x%01x\n",
- (*rev) >> 4);
+ in_8(rev) >> 4);
/*
* Initialize local bus.
*/
local_bus_init ();
- ecm->eedr = 0xffffffff; /* clear ecm errors */
- ecm->eeer = 0xffffffff; /* enable ecm errors */
+ out_be32(&ecm->eedr, 0xffffffff); /* clear ecm errors */
+ out_be32(&ecm->eeer, 0xffffffff); /* enable ecm errors */
return 0;
}
@@ -86,7 +86,7 @@
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- gur->ddrdllcr = 0x81000000;
+ out_be32(&gur->ddrdllcr, 0x81000000);
asm("sync;isync;msync");
udelay(200);
}
@@ -123,24 +123,24 @@
sys_info_t sysinfo;
get_sys_info(&sysinfo);
- clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2;
+ clkdiv = (in_be32(&lbc->lcrr) & LCRR_CLKDIV) * 2;
lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
- gur->lbiuiplldcr1 = 0x00078080;
+ out_be32(&gur->lbiuiplldcr1, 0x00078080);
if (clkdiv == 16) {
- gur->lbiuiplldcr0 = 0x7c0f1bf0;
+ out_be32(&gur->lbiuiplldcr0, 0x7c0f1bf0);
} else if (clkdiv == 8) {
- gur->lbiuiplldcr0 = 0x6c0f1bf0;
+ out_be32(&gur->lbiuiplldcr0, 0x6c0f1bf0);
} else if (clkdiv == 4) {
- gur->lbiuiplldcr0 = 0x5c0f1bf0;
+ out_be32(&gur->lbiuiplldcr0, 0x5c0f1bf0);
}
- lbc->lcrr |= 0x00030000;
+ setbits_be32(&lbc->lcrr, 0x00030000);
asm("sync;isync;msync");
- lbc->ltesr = 0xffffffff; /* Clear LBC error interrupts */
- lbc->lteir = 0xffffffff; /* Enable LBC error interrupts */
+ out_be32(&lbc->ltesr, 0xffffffff); /* Clear LBC error IRQs */
+ out_be32(&lbc->lteir, 0xffffffff); /* Enable LBC error IRQs */
}
/*
@@ -163,18 +163,18 @@
/*
* Setup SDRAM Base and Option Registers
*/
- lbc->or3 = CONFIG_SYS_OR3_PRELIM;
+ out_be32(&lbc->or3, CONFIG_SYS_OR3_PRELIM);
asm("msync");
- lbc->br3 = CONFIG_SYS_BR3_PRELIM;
+ out_be32(&lbc->br3, CONFIG_SYS_BR3_PRELIM);
asm("msync");
- lbc->lbcr = CONFIG_SYS_LBC_LBCR;
+ out_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
asm("msync");
- lbc->lsrt = CONFIG_SYS_LBC_LSRT;
- lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
+ out_be32(&lbc->lsrt, CONFIG_SYS_LBC_LSRT);
+ out_be32(&lbc->mrtpr, CONFIG_SYS_LBC_MRTPR);
asm("msync");
/*
@@ -186,7 +186,7 @@
/*
* Issue PRECHARGE ALL command.
*/
- lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL;
+ out_be32(&lbc->lsdmr, lsdmr_common | LSDMR_OP_PCHALL);
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
@@ -196,7 +196,7 @@
* Issue 8 AUTO REFRESH commands.
*/
for (idx = 0; idx < 8; idx++) {
- lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH;
+ out_be32(&lbc->lsdmr, lsdmr_common | LSDMR_OP_ARFRSH);
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
@@ -206,7 +206,7 @@
/*
* Issue 8 MODE-set command.
*/
- lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW;
+ out_be32(&lbc->lsdmr, lsdmr_common | LSDMR_OP_MRW);
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
@@ -215,7 +215,7 @@
/*
* Issue NORMAL OP command.
*/
- lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
+ out_be32(&lbc->lsdmr, lsdmr_common | LSDMR_OP_NORMAL);
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
@@ -263,45 +263,44 @@
}
#endif
-#if !defined(CONFIG_SPD_EEPROM)
+#if !defined(CONFIG_SPD_EEPROM)
+#define CONFIG_SYS_DDR_CONTROL 0xc300c000
/*************************************************************************
* fixed_sdram init -- doesn't use serial presence detect.
* assumes 256MB DDR2 SDRAM SODIMM, without ECC, running at DDR400 speed.
************************************************************************/
long int fixed_sdram (void)
{
- #define CONFIG_SYS_DDR_CONTROL 0xc300c000
-
volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR);
- ddr->cs0_bnds = 0x0000007f;
- ddr->cs1_bnds = 0x008000ff;
- ddr->cs2_bnds = 0x00000000;
- ddr->cs3_bnds = 0x00000000;
- ddr->cs0_config = 0x80010101;
- ddr->cs1_config = 0x80010101;
- ddr->cs2_config = 0x00000000;
- ddr->cs3_config = 0x00000000;
- ddr->timing_cfg_3 = 0x00000000;
- ddr->timing_cfg_0 = 0x00220802;
- ddr->timing_cfg_1 = 0x38377322;
- ddr->timing_cfg_2 = 0x0fa044C7;
- ddr->sdram_cfg = 0x4300C000;
- ddr->sdram_cfg_2 = 0x24401000;
- ddr->sdram_mode = 0x23C00542;
- ddr->sdram_mode_2 = 0x00000000;
- ddr->sdram_interval = 0x05080100;
- ddr->sdram_md_cntl = 0x00000000;
- ddr->sdram_data_init = 0x00000000;
- ddr->sdram_clk_cntl = 0x03800000;
+ out_be32(&ddr->cs0_bnds, 0x0000007f);
+ out_be32(&ddr->cs1_bnds, 0x008000ff);
+ out_be32(&ddr->cs2_bnds, 0x00000000);
+ out_be32(&ddr->cs3_bnds, 0x00000000);
+ out_be32(&ddr->cs0_config, 0x80010101);
+ out_be32(&ddr->cs1_config, 0x80010101);
+ out_be32(&ddr->cs2_config, 0x00000000);
+ out_be32(&ddr->cs3_config, 0x00000000);
+ out_be32(&ddr->timing_cfg_3, 0x00000000);
+ out_be32(&ddr->timing_cfg_0, 0x00220802);
+ out_be32(&ddr->timing_cfg_1, 0x38377322);
+ out_be32(&ddr->timing_cfg_2, 0x0fa044C7);
+ out_be32(&ddr->sdram_cfg, 0x4300C000);
+ out_be32(&ddr->sdram_cfg_2, 0x24401000);
+ out_be32(&ddr->sdram_mode, 0x23C00542);
+ out_be32(&ddr->sdram_mode_2, 0x00000000);
+ out_be32(&ddr->sdram_interval, 0x05080100);
+ out_be32(&ddr->sdram_md_cntl, 0x00000000);
+ out_be32(&ddr->sdram_data_init, 0x00000000);
+ out_be32(&ddr->sdram_clk_cntl, 0x03800000);
asm("sync;isync;msync");
udelay(500);
#if defined (CONFIG_DDR_ECC)
/* Enable ECC checking */
- ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
+ out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | 0x20000000);
#else
- ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
+ out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
#endif
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;