Cleanup (PPC4xx is AMCC now)
diff --git a/board/MAI/AmigaOneG3SE/ps2kbd.c b/board/MAI/AmigaOneG3SE/ps2kbd.c
index bfe5eb3..cf4f4d0 100644
--- a/board/MAI/AmigaOneG3SE/ps2kbd.c
+++ b/board/MAI/AmigaOneG3SE/ps2kbd.c
@@ -656,7 +656,7 @@
| KBD_MODE_DISABLE_MOUSE
| KBD_MODE_KCC);
- /* ibm powerpc portables need this to use scan-code set 1 -- Cort */
+ /* AMCC powerpc portables need this to use scan-code set 1 -- Cort */
kbd_write_command_w(KBD_CCMD_READ_MODE);
if (!(kbd_wait_for_input() & KBD_MODE_KCC)) {
/*
diff --git a/board/amcc/ocotea/config.mk b/board/amcc/ocotea/config.mk
index 5543a4e..9e18335 100644
--- a/board/amcc/ocotea/config.mk
+++ b/board/amcc/ocotea/config.mk
@@ -22,7 +22,7 @@
#
#
-# IBM 440GX Reference Platform (Ocotea) board
+# AMCC 440GX Reference Platform (Ocotea) board
#
#TEXT_BASE = 0xFFFE0000
diff --git a/board/dave/PPChameleonEVB/PPChameleonEVB.c b/board/dave/PPChameleonEVB/PPChameleonEVB.c
index 1f6512d..b425d63 100644
--- a/board/dave/PPChameleonEVB/PPChameleonEVB.c
+++ b/board/dave/PPChameleonEVB/PPChameleonEVB.c
@@ -279,10 +279,10 @@
case 1:
switch (pvr) {
case PVR_405EP_RB:
- sprintf (info, " IBM PowerPC 405EP Rev. B");
+ sprintf (info, " AMCC PowerPC 405EP Rev. B");
break;
default:
- sprintf (info, " IBM PowerPC 405EP Rev. <unknown>");
+ sprintf (info, " AMCC PowerPC 405EP Rev. <unknown>");
break;
}
return;
diff --git a/board/eric/eric.c b/board/eric/eric.c
index 860e506..02fe8dc 100644
--- a/board/eric/eric.c
+++ b/board/eric/eric.c
@@ -26,10 +26,10 @@
#include "eric.h"
#include <asm/processor.h>
-#define IBM405GP_GPIO0_OR 0xef600700 /* GPIO Output */
-#define IBM405GP_GPIO0_TCR 0xef600704 /* GPIO Three-State Control */
-#define IBM405GP_GPIO0_ODR 0xef600718 /* GPIO Open Drain */
-#define IBM405GP_GPIO0_IR 0xef60071c /* GPIO Input */
+#define PPC405GP_GPIO0_OR 0xef600700 /* GPIO Output */
+#define PPC405GP_GPIO0_TCR 0xef600704 /* GPIO Three-State Control */
+#define PPC405GP_GPIO0_ODR 0xef600718 /* GPIO Open Drain */
+#define PPC405GP_GPIO0_IR 0xef60071c /* GPIO Input */
int board_early_init_f (void)
{
@@ -50,7 +50,7 @@
| IRQ 30 (EXT IRQ 5) PCI INTB#; active low; level sensitive
| IRQ 31 (EXT IRQ 6) PCI INTA#; active low; level sensitive
| -> IRQ6 Pin is NOW GPIO23 and can be activateted by setting
- | IBM405GP_GPIO0_TCR Bit 0 = 1 (driving the output as defined in IBM405GP_GPIO0_OR,
+ | PPC405GP_GPIO0_TCR Bit 0 = 1 (driving the output as defined in PPC405GP_GPIO0_OR,
| else tristate)
| Note for ERIC board:
| An interrupt taken for the HOST (IRQ 28) indicates that
@@ -70,8 +70,8 @@
mtdcr (cntrl0, 0x00002000); /* set IRQ6 as GPIO23 to generate an interrupt request to the PCP2PCI bridge */
- out32 (IBM405GP_GPIO0_OR, 0x60000000); /*fixme is SMB_INT high or low active??; IRQ6 is GPIO23 output */
- out32 (IBM405GP_GPIO0_TCR, 0x7E400000);
+ out32 (PPC405GP_GPIO0_OR, 0x60000000); /*fixme is SMB_INT high or low active??; IRQ6 is GPIO23 output */
+ out32 (PPC405GP_GPIO0_TCR, 0x7E400000);
return 0;
}
diff --git a/board/esd/ocrtc/cmd_ocrtc.c b/board/esd/ocrtc/cmd_ocrtc.c
index 881d179..e113d5c 100644
--- a/board/esd/ocrtc/cmd_ocrtc.c
+++ b/board/esd/ocrtc/cmd_ocrtc.c
@@ -29,8 +29,8 @@
#if (CONFIG_COMMANDS & CFG_CMD_BSP)
-#define IBM_VENDOR_ID 0x1014
-#define PPC405_DEVICE_ID 0x0156
+#define AMCC_VENDOR_ID 0x1014
+#define PPC405_DEVICE_ID 0x0156
/*
@@ -43,7 +43,7 @@
u32 addr;
while (bdf >= 0) {
- if ((bdf = pci_find_device(IBM_VENDOR_ID, PPC405_DEVICE_ID, idx++)) < 0) {
+ if ((bdf = pci_find_device(AMCC_VENDOR_ID, PPC405_DEVICE_ID, idx++)) < 0) {
break;
}
printf("Found device nr %d at %x!\n", idx-1, bdf);
diff --git a/board/mpl/common/kbd.c b/board/mpl/common/kbd.c
index 9bd1ff9..7724e24 100644
--- a/board/mpl/common/kbd.c
+++ b/board/mpl/common/kbd.c
@@ -613,7 +613,7 @@
| KBD_MODE_DISABLE_MOUSE
| KBD_MODE_KCC);
- /* ibm powerpc portables need this to use scan-code set 1 -- Cort */
+ /* AMCC powerpc portables need this to use scan-code set 1 -- Cort */
kbd_write_command_w(KBD_CCMD_READ_MODE);
if (!(kbd_wait_for_input() & KBD_MODE_KCC)) {
/*
diff --git a/board/mpl/common/pci_parts.h b/board/mpl/common/pci_parts.h
index a57b121..60008e2 100644
--- a/board/mpl/common/pci_parts.h
+++ b/board/mpl/common/pci_parts.h
@@ -137,7 +137,7 @@
{ } /* end of device table */
};
/* PPC405 Dummy only used to prevent autosetup on this host bridge */
-static struct pci_pip405_config_entry ibm405_dummy[] = {
+static struct pci_pip405_config_entry ppc405_dummy[] = {
{ } /* end of device table */
};
@@ -150,7 +150,7 @@
PCI_DEVICE_ID_IBM_405GP,
PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID, 0,
- pci_pip405_write_regs, {(unsigned long) ibm405_dummy}},
+ pci_pip405_write_regs, {(unsigned long) ppc405_dummy}},
{PCI_VENDOR_ID_INTEL, /* PIIX4 ISA Bridge Function 0 */
PCI_DEVICE_ID_INTEL_82371AB_0,
diff --git a/board/w7o/fpga.c b/board/w7o/fpga.c
index 97af924..336bfba 100644
--- a/board/w7o/fpga.c
+++ b/board/w7o/fpga.c
@@ -77,17 +77,17 @@
dest = (unsigned short *)daddr;
/* Get DCR output register */
- grego = in32(IBM405GP_GPIO0_OR);
+ grego = in32(PPC405GP_GPIO0_OR);
/* Reset FPGA */
grego &= ~GPIO_XCV_PROG; /* PROG line low */
- out32(IBM405GP_GPIO0_OR, grego);
+ out32(PPC405GP_GPIO0_OR, grego);
/* Setup timeout timer */
start = get_timer(0);
/* Wait for FPGA init line */
- while(in32(IBM405GP_GPIO0_IR) & GPIO_XCV_INIT) { /* Wait INIT line low */
+ while(in32(PPC405GP_GPIO0_IR) & GPIO_XCV_INIT) { /* Wait INIT line low */
/* Check for timeout - 100us max, so use 3ms */
if (get_timer(start) > 3) {
printf(" failed to start init.\n");
@@ -100,10 +100,10 @@
/* Unreset FPGA */
grego |= GPIO_XCV_PROG; /* PROG line high */
- out32(IBM405GP_GPIO0_OR, grego);
+ out32(PPC405GP_GPIO0_OR, grego);
/* Wait for FPGA end of init period . */
- while(!(in32(IBM405GP_GPIO0_IR) & GPIO_XCV_INIT)) { /* Wait for INIT hi */
+ while(!(in32(PPC405GP_GPIO0_IR) & GPIO_XCV_INIT)) { /* Wait for INIT hi */
/* Check for timeout */
if (get_timer(start) > 3) {
@@ -112,7 +112,7 @@
/* Reset FPGA */
grego &= ~GPIO_XCV_PROG; /* PROG line low */
- out32(IBM405GP_GPIO0_OR, grego);
+ out32(PPC405GP_GPIO0_OR, grego);
goto done;
}
@@ -127,18 +127,18 @@
mtdcr(CPC0_CR0, greg); /* ... just do it */
/* turn on open drain for CNFG */
- greg = in32(IBM405GP_GPIO0_ODR); /* get open drain register */
+ greg = in32(PPC405GP_GPIO0_ODR); /* get open drain register */
greg |= cnfg; /* CNFG open drain */
- out32(IBM405GP_GPIO0_ODR, greg); /* .. just do it */
+ out32(PPC405GP_GPIO0_ODR, greg); /* .. just do it */
/* Turn output enable on for CNFG */
- greg = in32(IBM405GP_GPIO0_TCR); /* get tristate register */
+ greg = in32(PPC405GP_GPIO0_TCR); /* get tristate register */
greg |= cnfg; /* CNFG tristate inactive */
- out32(IBM405GP_GPIO0_TCR, greg); /* ... just do it */
+ out32(PPC405GP_GPIO0_TCR, greg); /* ... just do it */
/* Setup FPGA for programming */
grego &= ~cnfg; /* CONFIG line low */
- out32(IBM405GP_GPIO0_OR, grego);
+ out32(PPC405GP_GPIO0_OR, grego);
/*
* Program the FPGA
@@ -149,12 +149,12 @@
/* Done programming */
grego |= cnfg; /* CONFIG line high */
- out32(IBM405GP_GPIO0_OR, grego);
+ out32(PPC405GP_GPIO0_OR, grego);
/* Turn output enable OFF for CNFG */
- greg = in32(IBM405GP_GPIO0_TCR); /* get tristate register */
+ greg = in32(PPC405GP_GPIO0_TCR); /* get tristate register */
greg &= ~cnfg; /* CNFG tristate inactive */
- out32(IBM405GP_GPIO0_TCR, greg); /* ... just do it */
+ out32(PPC405GP_GPIO0_TCR, greg); /* ... just do it */
/* Toggle IRQ/GPIO */
greg = mfdcr(CPC0_CR0); /* get chip ctrl register */
@@ -180,7 +180,7 @@
start = get_timer(0);
/* Wait for FPGA end of programming period . */
- while(!(in32(IBM405GP_GPIO0_IR) & GPIO_XCV_DONE)) { /* Test DONE low */
+ while(!(in32(PPC405GP_GPIO0_IR) & GPIO_XCV_DONE)) { /* Test DONE low */
/* Check for timeout */
if (get_timer(start) > 3) {
@@ -189,7 +189,7 @@
/* Reset FPGA */
grego &= ~GPIO_XCV_PROG; /* PROG line low */
- out32(IBM405GP_GPIO0_OR, grego);
+ out32(PPC405GP_GPIO0_OR, grego);
goto done;
}
diff --git a/board/w7o/w7o.c b/board/w7o/w7o.c
index 1e3ceb2..daf7f53 100644
--- a/board/w7o/w7o.c
+++ b/board/w7o/w7o.c
@@ -47,9 +47,9 @@
/*
* Setup GPIO pins - reset devices.
*/
- out32 (IBM405GP_GPIO0_ODR, 0x10000000); /* one open drain pin */
- out32 (IBM405GP_GPIO0_OR, 0x3E000000); /* set output pins to default */
- out32 (IBM405GP_GPIO0_TCR, 0x7f800000); /* setup for output */
+ out32 (PPC405GP_GPIO0_ODR, 0x10000000); /* one open drain pin */
+ out32 (PPC405GP_GPIO0_OR, 0x3E000000); /* set output pins to default */
+ out32 (PPC405GP_GPIO0_TCR, 0x7f800000); /* setup for output */
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
@@ -78,9 +78,9 @@
/*
* Setup GPIO pins
*/
- out32 (IBM405GP_GPIO0_ODR, 0x01800000); /* XCV Done Open Drain */
- out32 (IBM405GP_GPIO0_OR, 0x03800000); /* set out pins to default */
- out32 (IBM405GP_GPIO0_TCR, 0x66C00000); /* setup for output */
+ out32 (PPC405GP_GPIO0_ODR, 0x01800000); /* XCV Done Open Drain */
+ out32 (PPC405GP_GPIO0_OR, 0x03800000); /* set out pins to default */
+ out32 (PPC405GP_GPIO0_TCR, 0x66C00000); /* setup for output */
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
@@ -238,14 +238,14 @@
#if defined(CONFIG_W7OLMG)
unsigned long greg; /* GPIO Register */
- greg = in32 (IBM405GP_GPIO0_OR);
+ greg = in32 (PPC405GP_GPIO0_OR);
/*
* XXX - Unreset devices - this should be moved into VxWorks driver code
*/
greg |= 0x41800000L; /* SAM, PHY, Galileo */
- out32 (IBM405GP_GPIO0_OR, greg); /* set output pins to default */
+ out32 (PPC405GP_GPIO0_OR, greg); /* set output pins to default */
#endif /* CONFIG_W7OLMG */
/*
diff --git a/board/w7o/w7o.h b/board/w7o/w7o.h
index 8458166..d6f50e2 100644
--- a/board/w7o/w7o.h
+++ b/board/w7o/w7o.h
@@ -25,13 +25,13 @@
#define _W7O_H_
#include <config.h>
-/* IBM 405GP PowerPC GPIO registers */
-#define IBM405GP_GPIO0_OR 0xef600700L /* GPIO Output */
-#define IBM405GP_GPIO0_TCR 0xef600704L /* GPIO Three-State Control */
-#define IBM405GP_GPIO0_ODR 0xef600718L /* GPIO Open Drain */
-#define IBM405GP_GPIO0_IR 0xef60071cL /* GPIO Input */
+/* AMCC 405GP PowerPC GPIO registers */
+#define PPC405GP_GPIO0_OR 0xef600700L /* GPIO Output */
+#define PPC405GP_GPIO0_TCR 0xef600704L /* GPIO Three-State Control */
+#define PPC405GP_GPIO0_ODR 0xef600718L /* GPIO Open Drain */
+#define PPC405GP_GPIO0_IR 0xef60071cL /* GPIO Input */
-/* IBM 405GP DCRs */
+/* AMCC 405GP DCRs */
#define CPC0_CR0 0xb1 /* Chip control register 0 */
/* LMG FPGA <=> CPU GPIO signals */