commit 0ca4d40cfe598b55c377fffdee1970c44e73fbda
author Jagan Teki <jagan@amarulasolutions.com> Sun Aug 05 00:40:12 2018 +0530
committer Jagan Teki <jagan@amarulasolutions.com> Mon Aug 13 13:07:35 2018 +0530
tree ff8f6a8671dbc83b535094b3c66e45b7ee8139cd
parent cf6822574251c73133d1b4943fbe9b054f8f70e5

ARM: dts: sun8i: Update A83T dts(i) files from Linux-v4.18-rc3

Update all A83T devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 221cb9fd2ee3042689fe0e6613d0f34eb46a5af6
Author: Mylène Josserand <mylene.josserand@bootlin.com>
Date:   Fri May 4 21:05:44 2018 +0200

    ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC

Note: bananapi-m3 and cubietruck-plus board dts files has
usb_otg enabled in U-Boot which were not present in Linux.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arch/arm/dts/sun8i-a83t-bananapi-m3.dts

diff --git a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
index dfc16a0..eaff6fa 100644
--- a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
@@ -1,6 +1,7 @@
 /*
- * Copyright 2015 Vishnu Patekar
- * Vishnu Patekar <vishnupatekar0510@gmail.com>
+ * Copyright 2017 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -44,29 +45,316 @@
 /dts-v1/;
 #include "sun8i-a83t.dtsi"
 
+#include <dt-bindings/gpio/gpio.h>
+
 / {
-	model = "Allwinner A83T BananaPi M3 Board v1.2";
-	compatible = "bananapi,m3v1.2", "allwinner,sun8i-a83t";
+	model = "Banana Pi BPI-M3";
+	compatible = "sinovoip,bpi-m3", "allwinner,sun8i-a83t";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		blue {
+			label = "bananapi-m3:blue:usr";
+			gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		green {
+			label = "bananapi-m3:green:usr";
+			gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	reg_usb1_vbus: reg-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&ac100_rtc 1>;
+		clock-names = "ext_clock";
+		/* The WiFi low power clock must be 32768 Hz */
+		assigned-clocks = <&ac100_rtc 1>;
+		assigned-clock-rates = <32768>;
+		/* enables internal regulator and de-asserts reset */
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+	};
+};
+
+&de {
+	status = "okay";
 };
 
 &ehci0 {
+	/* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */
 	status = "okay";
+
+	/* TODO GL830 USB-to-SATA bridge downstream w/ GPIO power controls */
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_sw>;
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii";
+	allwinner,rx-delay-ps = <700>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mdio {
+	rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_dldo1>;
+	vqmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp81x: pmic@3a3 {
+		compatible = "x-powers,axp813";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		eldoin-supply = <&reg_dcdc1>;
+		fldoin-supply = <&reg_dcdc5>;
+		swin-supply = <&reg_dcdc1>;
+		x-powers,drive-vbus-en;
+	};
+
+	ac100: codec@e89 {
+		compatible = "x-powers,ac100";
+		reg = <0xe89>;
+
+		ac100_codec: codec {
+			compatible = "x-powers,ac100-codec";
+			interrupt-parent = <&r_pio>;
+			interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
+			#clock-cells = <0>;
+			clock-output-names = "4M_adda";
+		};
+
+		ac100_rtc: rtc {
+			compatible = "x-powers,ac100-rtc";
+			interrupt-parent = <&r_intc>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&ac100_codec>;
+			#clock-cells = <1>;
+			clock-output-names = "cko1_rtc",
+					     "cko2_rtc",
+					     "cko3_rtc";
+		};
+	};
+};
+
+#include "axp81x.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-1v8";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dram-pll";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_dcdc1 {
+	/* schematics says 3.1V but FEX file says 3.3V */
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpub";
+};
+
+&reg_dcdc4 {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <900000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	/*
+	 * This powers both the WiFi/BT module's main power, I/O supply,
+	 * and external pull-ups on all the data lines. It should be set
+	 * to the same voltage as the I/O supply (DCDC1 in this case) to
+	 * avoid any leakage or mismatch.
+	 */
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vcc-pd";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1080000>;
+	regulator-max-microvolt = <1320000>;
+	regulator-name = "vdd12-hsic";
+};
+
+&reg_fldo2 {
+	/*
+	 * Despite the embedded CPUs core not being used in any way,
+	 * this must remain on or the system will hang.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&reg_sw {
+	/*
+	 * The PHY requires 20ms after all voltages
+	 * are applied until core logic is ready and
+	 * 30ms after the reset pin is de-asserted.
+	 * Set a 100ms delay to account for PMIC
+	 * ramp time and board traces.
+	 */
+	regulator-enable-ramp-delay = <100000>;
+	regulator-name = "vcc-ephy";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_b>;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 
 &usb_otg {
 	status = "okay";
 };
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};